Alcoscan AL7000 User manual

User’s Manual
AL7000 is intended to measure alcohol in human breath. Readings obtained by this device are used in the
diagnosis of alcohol intoxication.
The accuracy of this device has been established at a Blood Alcohol Concentration of 0.000and0.400%BAC.
Accuracy testing was completed according to DOT regulations.
The AlcoScan Model AL7000 analyzes a breath sample to detect alcohol in the lungs.
This reading is then converted to blood alcohol concentration (BAC).
AL7000 uses an advanced oxide semiconductor sensor to detect alcohol.
…………………………………………………………………………………………………………………………
Specifications
Method of Measure Breath sample to BAC
Range 0.000% to 0.400%BAC or 0.000‰ to 4.000‰ or 0.000mg/l to 2.000mg/lBrAC
Accuracy +/-0.01%BAC up to 0.10% BAC
Sensor Oxide semiconductor
Power Two 1.5V AA alkaline batteries (included)
Testing Capacity Approx. 100~200 with new batteries
Operating Temperature 10 – 40 degrees Celsius
Warm Up Less than 1 minute
Display 3-digit LCD
Size (mm) 105(height) X 50(width) X 18(thickness)
Weight 98g
Sensor Modules Sensor modules should be replaced approx. 300 tests,
or if damaged by improper testing or handling
HADRON

…………………………………………………………………………………………………………………………
How to use
Press the Power
Switch.
Warm up. Blowing through
The mouthpiece
Into the unit for
4 seconds until
beep twice.
The result is
Displayed for
15 seconds.
Automatically
turning off.
*. If you press and hold the Power Switch, you can check the accumulated total test counts.
…………………………………………………………………………………………………………………………
AL7000 is the breathalyzer that features Pre-Calibrated Alcohol S
ensor Modules to eliminate the need for
recalibration.
Just snap out, snap in and you’re ready to go!
Sensor Module Replacement
Please take the following steps to install new sensor module. (★ You have to turn off the power first)
Make sure the
module is
connected tightly.
Close the sensor
cover then test.
Replace the new
sensor module into
original position.
You can see the
sensor module.
Take off PCB.
Open the sensor
cover.
HADRON

…………………………………………………………………………………………………………………………
Warnings
a. Wait at least 20 minutes after eating or drinking before testing. Alcohol remaining in the mouth, or even
excess saliva, may interfere with testing. This includes alcohol-based mouthwash or similar products.
b. Avoid testing in high wind or enclosed spaces. Poor ventilation may also lengthen the time required for
warm up between tests.
c. Do not blow smoke, saliva or other contaminants into the mouthpiece, as the sensor may become
damaged.
d. Do NOT use the AL7000 as a tool to drink and drive.
e. Keep out of extreme temperatures and out of the reach of children.
…………………………………………………………………………………………………………………………
Warning Display
Warning Display
If you see “Flow” in the display, the breath sample was not strong enough
for measurement. Please power on the unit again and make sure the
breath is strong and steady during sampling.
If you test over 300 tests, AL7000 will display “CAL” sign for 15 seconds
then warning up for test. This “CAL” sign will be provided the appropriate
time for calibration or replacement sensor module.
Please replace the batteries.
If you see “bat” in the display, the battery power is low.
HADRON

…………………………………………………………………………………………………………………………
Contents
Breathalyzer, Mouthpieces(x5), AA Batteries(x2), Pouch, Hand strip, 12V DC cable
12V Alternative power
You can use alternative
power from car cigar jack
lighter with provided cable.
Mouthpiece Holder
It can keep 2pcs
mouthpieces inside
of breathalyzer.
…………………………………………………………………………………………………………………………
Warranty
The manufacturer warrants the product to be free from defects in workmanship or material (excluding calibration)
under normal use for six (6) months from the date of purchase.
The manufacturer’s obligation under this warranty is limited to replacing, adjusting or repairing the unit if returned
along with proof of purchase. This warranty is void if the unit has been tampered with or maliciously damaged.
…………………………………………………………………………………………………………………………
Recalibration & Service
For recalibration and technical support, please contact us at:
HADRON