Alemite 3644-C2 Supplement
Short guide
Guide rapide
Schnellfuhrer
Guida rapida
Guía rapida
BULLETIN M 0093B ML REV.1
PRESET
BATCH
METER
SHORT GUIDE
Total type (Total or
Resettable Total)
Batch Total
Batch total
measurement
unit
Total
measurement
unit
Operation in
AUTO mode
AUTO key
to select and
confirm the
preset value
RESET key to reset
the Batch Total
and display the
Resettable Total
Numeric keys
to set the
preset value
2
Warning
In case of manual anti-drip valve,
after using, it is important to discharge the
overpressure between the chamber (1) and the
manual valve (2) of the spout. Carry out this operation
while the pump is switched off. Then, unscrew the valve (2).
During this discharging operation, do not push the trigger (3).
1
2
3
ADispensing in
manual mode
If the METER is off, type
RESET to re-start it.
The METER displays:
Non-resettable Total.
Last amount dispensed.
To reset the Batch Total press
RESET.
The METER will display:
Reset Batch Total.
Resettable Total.
To RESET the
Resettable Total, press
and hold down the
RESET key.
The METER will display:
Resettable Total.
Release the trigger to
stop dispensing.
Pull the trigger to
dispense.
To select a new PRESET value (for
example 12.3) use the numeric keys.
The METER displays:
Blinking message AUTO.
Selected value.
To confirm the PRESET
value, press and hold
down the AUTO key
until the METER
displays:
Selected value.
Reset Batch Total.
AUTO
message
not blinking.
Setting a new
PRESET value.
If the METER is off, type RESET
to re-start it. METER displays:
Non-resettable Total.
BSetting the PRESET value
for AUTO mode
dispensing
3
English
METER stores:
AUTO last:
the last PRESET value used
AUTO 1-2-3-4-5:
five different PRESET values of
frequent use.
If the unit is off, type RESET to re-start it.
The METER displays:
Non-resettable total.
Last amount dispensed.
Press AUTO.
The METER displays the
PRESET value stored in
AUTO LAST.
Blinking
message AUTO LAST.
PRESET value.
Press AUTO again. The
METER displays the PRESET
value stored in AUTO 1.
Blinking
message AUTO 1.
PRESET value.
To display the other stored
values, press AUTO as many
times as necessary to reach
the desired values.
Blinking message
will be:
METER is ready to start dispensing
in AUTO mode (see paragraph C).
Selecting a PRESET
value of frequent use.
To confirm a PRESET
value press and hold
down the AUTO key
until the METER
displays:
Selected value.
Reset Batch Total.
AUTO message
Not blinking.
METER is ready to start dispensing
in AUTO mode (see paragraph C).
41-800-548-1191 - http://www.partdeal.com - [email protected]
C
Blinking value.
Pull the trigger
completely and then
release it.
The trigger thus
remains locked in open
position. Now
dispensing can
continue in AUTO
mode
• To start dispensing:
• To stop manually dispensing in
progress:
Pull again the trigger completely and
then release it.
Warning
In any case the operator must
attend to the METER while
dispensing in AUTO mode in
order to avold any oil spillage
• Automatic stop:
The supply automatically stops when
the pre-set value is reached..
• Manual resumption of the
dispensing (TOPPING UP):
Once dispensing has been carried out
in AUTO mode, the METER allows the
user to continue the dispensing
operation, if necessary.
To carry out the TOPPING UP,
DO NOT type RESET and pull
the trigger.
The dispensed amount is added to the
previous one in AUTO mode.
The PRESET value previously set,
displayed in the Total, starts blinking
to indicate that the pre-set value has
been exceeded.
The AUTO indication
disappears from the LCD.
Dispensing in
AUTO mode
5
English
Other manuals for 3644-C2
1
Table of contents
Other Alemite Measuring Instrument manuals
