9
IGNITION WIGNITION WIRIRE(S) (WHITE) and (WHITE WITH RED STRIPE) (+12V in run, crankE(S) (WHITE) and (WHITE WITH RED STRIPE) (+12V in run, crank
and s metimes access ry)and s metimes access ry)
Make all c nnecti ns as cl se t the igniti n switch as p ssibleMake all c nnecti ns as cl se t the igniti n switch as p ssible..
The igniti n wire(s) are als l cated in the main harness c ming fr m the igniti n
switch. Check y ur chart f r pr bable c l rs and pr be each wire with y ur pr vided
test pr be. The c rrect igniti n wire(s) will sh w +12V and the RED light will gl w
bright when the igniti n switch is in the RUN, CR
RUN, CRANK ANK and s metimes in the
ACCESSOR
ACCESSORYY (newer GMs) p siti n. The c rrect wires will n t sh w +12V when
in the OF
OFFF r AACCESSORCCESSORYY p siti n ( ther than s me GMs).
1. If your vehicle has only one (1) ignition wire connect the heavy gauge
WHITE
WHITE wire to the Ignition #1 wire in the Ignition Switch Harness.
2. If your vehicle has (2) ignition wires, connect the WHITE
WHITE wire as stated
in step 1, to Ignition #1, then connect the heavy gauge WHITE WITHWHITE WITH
RE STRIPERE STRIPE wire to the Ignition #2 wire in the Ignition Switch Harness.
3. If your vehicle has (3) Ignition wires connect the heavy gauge WHITEWHITE
wire to the Ignition #1 wire and Ignition #3 wire in the Ignition Switch
Harness. Make sure you connect the WHITE WITH RED STRIPE wire to
the Ignition #2 wire as stated in Step 2.
ACCESSORACCESSORYY WIRE(S) WIRE(S) THATHATT POWER POWER THE HEATHE HEATER/BLOWER MOTTER/BLOWER MOTOR (WHITE WITHOR (WHITE WITH
BLACK STRIPE) (+12V in run r n p siti ns). BLACK STRIPE) (+12V in run r n p siti ns). This wire is als in the main igniti n switchThis wire is als in the main igniti n switch
harnessharness. Make this c nnecti n as cl se t the igniti n switch as p ssib. Make this c nnecti n as cl se t the igniti n switch as p ssible.le.
M st vehicles will have ne (1) access ry wire; h wever s mes me F rds, newer GM vehicles
and Chrysler 94 and up will have tw (2) r m re access ry wires. Check y ur wire c l r
chart and then verify these wire(s).
The c rrect wire(s) will sh w +12V and the RED
light will gl w bright
when the igniti n switch is in the ACCACC r RUN RUN r p siti ns, but never
OFF
OFF r CRANKCRANK.
1. If y ur vehicle has nly ne (1) access ry wire c nnect the heavy gauge WHITE WITH
WHITE WITH
BLACK STRIPEBLACK STRIPE wire t this wire.
2. If y ur vehicle has tw (2) access ry wires (s me GMs and m st F rds), c nnect the
WHITE WITH BLACK STRIPE
WHITE WITH BLACK STRIPE wire t b th access ry wires. In s me cases, if y u did
LOCATING & MAKING CONNECTIONS
16
OPERATOR PROGRAMMING
RUNTIME CONFIRMARUNTIME CONFIRMATION:TION:
With the vehicle n t running press and release Butt n #2, the parking
lights will flash (1) ne time f r each 5 minutes f pr grammed run time.
Example: (2) tw flashes = 10 minutes
TTO SETO SET THE RUNTIMETHE RUNTIME
:
Press and h ld Butt n #2 n the rem te c ntr l f r appr x. 10 sec nds
r until the parking lights begin t flash ( ne flash f r each 5 minutes f
runtime) and when Butt n #2 is released the new runtime is pr grammed.
T check this pr grammed runtime f r example, press and release Butt n
#2 if the parking lights flash (3) three times, the unit is pr grammed t run
f r 15 minutes.
CCLEARING LEARING THE UNITS MEMORTHE UNITS MEMORYY::
Press and h ld the brake, with the brake held, cycle the key in the igniti n
switch fr m OFF t RUN, (5) five times within 4 sec nds, the parking lights
will flash (3) three times. Unplug the unit fr m ALL wires and harnesses,
wait 30 sec nds, plug the unit back int all harnesses, the units mem ry
is n w cleared, set back t fact ry settings and ready t learn a rem te.
Y u must f ll w the initializati n pr cedure n page 13 t repr gram the
transmitter.
HOW TO USE YOUR NEW REMOTE
SSttartart
Press and release Butt n #1 the vehicle will rem te
start.
S
St pt p
Press and release Butt n #2 the vehicle will shut
d wn.
Pit S
Pit St p: Exiting the Vt p: Exiting the Vehicle with the Engineehicle with the Engine
RunningRunning
Make sure the transmissi n is in park
and the brake is n t pressed then
press and release Butt n #1 (start)
bef re turning the igniti n switch ff.
(The engine will remain running f r
15 minutes r until the brake is pressed).
SSttartart
Using the rem te included in this kit:Using the rem te included in this kit: Press and release Butt n #1.
Using y ur fact ry keyless entry rem te:Using y ur fact ry keyless entry rem te: Press the L ck butt n (3) times.
Using Using AfAftermarket termarket Alarm:Alarm: Press the sec nd channel butt n n y ur rem te transmitter.
SSt pt p
Using the rem te included in this kit: Using the rem te included in this kit: Press Butt n #2.
Using y ur fact ry keyless entry rem te:Using y ur fact ry keyless entry rem te: Press the L ck butt n (3) times again.
Using Using AfAftermarket termarket Alarm:Alarm: Press and release the sec nd channel butt n n y ur rem te
transmitter.
Pit SPit St p (Exiting the Vt p (Exiting the Vehicle with the Engine Running)ehicle with the Engine Running)
With y ur fact ry keyless rem te:With y ur fact ry keyless rem te:
If the vehicle is running with the igniti n key, pressing the L ck butt n n the fact ry keyless
will cause the parking lights t flash nce (if c nnected). Y u can n w turn ff y ur igniti n
key, rem ve the key and exit the vehicle. The vehicle will remain running f r 15 minutes.
NOTE: S me vehicleNOTE: S me vehicles fact ry keyless w nt w rk if the engine is running. If y ur vs fact ry keyless w nt w rk if the engine is running. If y ur vehicleehicle
perates in this fashi n, pit st p will n t functi n.perates in this fashi n, pit st p will n t functi n.
F r wiring charts please visit ur website, www.alertaut m tive.c m.
M st f the wires y u will be using will be in a tM st f the wires y u will be using will be in a taped r nyl n sleeve c mingaped r nyl n sleeve c ming
fr m the igniti n switch. fr m the igniti n switch. YYu must find and rem ve ab ut six inches f thisu must find and rem ve ab ut six inches f this
uter c vering f r testing and c nnecting.uter c vering f r testing and c nnecting.
CONSTCONSTANTANT POWER (RED) POWER (RED) (+12V(+12V, key in any p siti n including f, key in any p siti n including ff)f)
Make all c nnecti ns as cl se t the igniti n switch as p ssibleMake all c nnecti ns as cl se t the igniti n switch as p ssible..
These wire(s) are in y ur vehicles main igniti n harness, usually l cated in the
steering c lumn c ming fr m the igniti n switch. Pr be each wire with y ur
pr vided test pr be. The c rrect wire(s) will sh w +12V and the RED light will
gl w bright n the test pr be when the igniti n switch is in these 5 p siti ns5 p siti ns
(ACC-LOCK-OFF-RUN-CRANK)(ACC-LOCK-OFF-RUN-CRANK).
1. If y ur vehicle has nly (1) c nstant p wer wire, attach
b th heavy gauge REDRED wires t it.
2. If y ur vehicle has (2) c nstant p wer wires, attach ne REDRED wire t each.
IGNITION HARNESSIGNITION HARNESS
UNDER DASHUNDER DASH
