ALIBI ALI-NVR3308P User manual

1ALI-NVR3304-08-16P_SQ
170707
ALI-NVR3316P Backpanel
Internal Ethernet switch
ports with PoE (16)
LAN
Fan
outlet
Video Out
(VGA, HDMI)
Audio
IN/OUT
Alarm
IN/OUT
USB Power cord
connector
Power
switch
Ground
terminal
Item Description
VIDEO OUT (VGA, HDMI) 1 channel (HDMI/VGA). See “Specications” on page 4 for supported output resolutions.
Audio IN / OUT RCA connectors for audio line input and line output
Alarm IN / OUT Terminations are provided for 4 alarm inputs (N.O. or N.C.) and 1 alarm output. See below. (ALI-NVR3308P and ALI-NVR3316P only)
Power connector
ALI-NVR3304P: Connect the 48 Vdc power adapter provided with the recorder to this port, and to a standard 100 ~ 240 Vac power
source using the power cord provided.
ALI-NVR3308P and ALI-NVR3316P: Connect the power cord provided with the recorder to this port and to a standard 100 ~ 240 Vac
power source.
ON / OFF Switch Switch for powering the recorder on or o.
GROUND Terminal for ground. Connect to earth ground before powering on the NVR.
LAN 10/100BASE-T (ALI-NVR3304P) or 10/100/1000BASE-T (ALI-NVR3308P and ALI-NVR3316) Ethernet network interface
USB interface Universal Serial Bus (USB) port for additional devices such as USB mouse and USB Hard Disk Drive (HDD). USB 3.0 port in ALI-NVR3308P
and ALI-NVR3316P only.
Internal Ethernet switch ports 4 (ALI-NVR3304P) or 8 (ALI-NVR3308P) or 16 (ALI-NVR3316P) 10/100 Mbps ports for IP cameras. These ports provide Power over
Ethernet (PoE).
Alarm IN / OUT Terminals (ALI-NVR3308P and ALI-NVR3316P only)
Item Description
ALARM IN (1 through 4 and
G, G (ground)) Alarm inputs 1 - 4. Alarm input is tied to ground at G or G terminals through the alarm sensor (N.O. or N.C.).
ALARM OUT (1 and G) Alarm outputs 1 with ground termination.
Mouse control
A standard 3-button (left / right / scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse:
This quick setup guide provides instructions to initially setup and use the ALI-NVR3304P, ALI-NVR3308P and ALI-NVR3316P network
video recorders (NVRs). For information about using your NVR and its extensive capabilities, refer to the Alibi Embedded Network Video
Recorder Firmware V3.4.x User Manual provided at www.alibisecurity.com/resources.
For more information, refer to these documents - available from your equipment vendor:
• ALIBI™ Tools Utility Installation and User Manual
• ALIBI™ Witness Smartphone App for Android - Quick Start Guide
Controls and Indicators
Front panel
Status indicators USB port
Item Function / Description
Status Indicators
POWER Indicator is green when the unit is powered on. When the unit is o, the LED is red if power is available.
HDD HDD indicator blinks red when data is being read from or written to an HDD.
TX/RX Blinks green when the network connection is functioning normally.
USB Interfaces Universal Serial Bus (USB) 2.0 port for additional USB devices such as a mouse or Hard Disk Drive (HDD).
ALI-NVR3304P Backpanel
Audio IN/OUT
Internal Ethernet switch
ports with PoE (4)
LAN
Power Adapter
connector
Power switch
Video Out
(VGA, HDMI)
Ground
terminal
USB
ALI-NVR3308P Backpanel
Internal Ethernet switch
ports with PoE (8)
LAN
Fan
outlet
Video Out
(VGA, HDMI)
Audio
IN/OUT
Alarm
IN/OUT
USB Power cord
connector
Power
switch
Ground
terminal
ALI-NVR3304P, ALI-NVR3308P, ALI-NVR3316P Embedded Network Video Recorders Quick Setup Guide

2www.Observint.com © 2017 Observint Technologies, Inc. All rights reserved.
Step 2. HDD Installation
If you purchased your NVR without a HDD, or you want to replace the HDD installed in your NVR or add another, use “APPENDIX A HDD
Installation” on page 5 as a guideline.
Step 3. Install the NVR
For the following steps, refer to the back panel photo above for the location of connectors.
1. Place the NVR in a location that is secure, well ventilated and clean. The NVR should be positioned such that the back panel connectors
are accessible and the ventilation holes on the sides are not blocked.
2. Connect the ground terminal on the back of the NVR to an earth ground. Refer to local codes for proper grounding.
Step 4. Connect alarm devices to the NVR
Wiring alarm inputs to the NVR
You can wire up to 4 alarm inputs to the NVR.
Alarm IN sensor (N.O. or N.C.)
Typical ALARM IN wiring
Wiring alarm outputs to the NVR
The NVR provides 1 alarm output termination that supports a DC load alarm out circuit. These terminations are marked on the back of the
NVR and are labeled OUT 1 G (G = ground termination).
DC load alarm output circuits
DC loads must operate within the limitation of 12V / 1A. To connect to a DC alarm output, use the following diagram:
NVR
DC Load
1. Plug the USB mouse into the either the front panel or back panel USB connector of the NVR.
2. The mouse will be automatically detected. If the mouse is not detected, the mouse may not be compatible with the NVR. Please refer
to the recommended device list from your provider.
Using the mouse
Action Eect
Left click
Single click: Live view: Select channel and show the quick set menu.
Menu: Select and enter.
Double click: Live view: Switch between single-screen and multi-screen.
Click and drag: PTZ control: pan, tilt and zoom.
Tamper-proof, privacy mask and motion detection: Select target area.
Digital zoom-in: Drag and select target area.
Live view: Drag channel / time bar
Right click Live view: Show menu.
Menu: Exit current menu to upper level menu.
Scroll wheel
Scroll up: Live view: Previous screen.
Menu: Previous item.
Scroll down: Live view: Next screen.
Menu: Next item.
Step 1. Getting Started: Unpacking the Equipment
What’s in the box
Your system includes:
• NVR
• 48 Vdc power adapter (ALI-NVR3304P only)
• 6 foot Ethernet cable
• 6 foot HDMI cable
• Power cable for ALI-NVR3308P and ALI-NVR3316P, power adapter and cable for ALI-NVR3304P
• HDD SATA and power interface cables for internal hard disk drive(s)
Remove the equipment from its packaging and place it on a at, clean surface. Inspect each item. If any visible damage is present, contact
your supplier for a replacement. Verify that your order is complete.
What you need
Although each security system installation is dierent, most require the following items not included with your system components:
• VGA or HDMI compatible computer monitor
• IP cameras and cables compatible with the NVR
• Tools to install the cameras and route power and Ethernet cables
• Fasteners to attach the cameras to the mounting surfaces
• A display device to connect to the NVR. The NVR will connect directly to a VGA video monitor or an HDMI monitor (HDMI cable is
provided). The display device is usually needed only for system setup. It can be disconnected when the NVR is networked for access
across a LAN or Internet.
• Uninterruptible power supply (UPS). This device is used to ensure system stability during voltage surges, sags, and outages. If a UPS is
not available, a power strip with strong surge protection is highly recommended.

3www.Observint.com
© 2017 Observint Technologies. All rights reserved.
By default, the Setup Wizard will open automatically. Refer to the Alibi Embedded Network Video Recorder Firmware V3.4.90 User
Manual provided at www.alibisecurity.com/resources for incomplete instructions for using the Wizard and conguring and using your
NVR.
Important Notes for using the Wizard:
• Password: When logging into the recorder for the rst time, create a “Strong” administrator user password. Follow the on-screen
instructions, and save this password and the GUID le created by the rmware in a secure location. NOTE: There is no factory default
password for this device.
• Date and Time: Set the time zone, date and time correctly. All recorded video and capture (photo) les are time stamped.
• Storage - HDD: In the HDD Management wizard, if a new recorder is shipped with a pre-congured HDD, nothing needs to be done
with it in this window. If you installed an HDD or replaced the HDD, that HDD needs to be initialized by the recorder before it can be
used to record data. Select (check the box for) that HDD, then click Init to initialize the disk. NOTE: Init will erase all data from the
disk and can take several minutes to complete. When the initialization is complete, click Next to continue.
• Network Settings: By default, the recorder acquires it’s network settings using DHCP (dynamic network settings). Depending on
the conguration of the network, these settings may change. To improve remote access to the recorder, Observint recommends that
you congure the DVR with xed network settings. To easily change the DHCP acquired network settings to xed network settings,
un-check the Enable DHCP option in the network setup menu, and then click Apply.
Step 9. Access the Menu system
After the initial setup of your QVR using the Wizard, the Menus interface enables you to rene your conguration settings and expand the
functionality of the system. To use most menus, the user must log into the NVR system, either locally or remotely, with administrative
privileges. To open the Menu system from the Live View screen, right click anywhere in the screen, then select Menu.
Step 5. Install a monitor, mouse, power
For the following steps, refer to the back panel photo above for the location of connectors.
1. Install and setup your monitor in accordance with the instructions provided with the monitor. Do not power it on at this time.
2. Cable the HDMI or VGA connector to your monitor’s VGA or HDMI input. The HDMI interface provides the best performance.
3. Plug the mouse into the USB connector on the front or back of the NVR.
4. If you plan to access your NVR remotely, or congure your NVR to transmit alerts, email, etc. to external servers, plug a drop cable from
your local area network (LAN) into the RJ45 LAN connector on the back of the NVR.
5. Connect the power cord (or power adapter for ALI-NVR3304P only) to the power connector on the back panel of the NVR, and then
into a UPS (recommended) or surge protector.
Step 6. Install cameras
Install your security cameras. Always follow the installation instructions provided with the camera. NOTE: If the cameras feature Power over
Ethernet PoE), the cameras that plug into the ports on the back of the NVR can be powered through those ports.
Step 7. Connecting it together – initial system setup
1. Plug the Ethernet drop cables from the cameras into the RJ-45 Ethernet Switch Ports on back of the NVR.
2. Power on your cameras.
3. Power on the NVR using the power on / o (I / O) switch on the back panel.
4. Power on the monitor.
NOTE Some monitors have multiple inputs such including VGA ,HDMI, BNC, etc. If you are using this kind of monitor, congure your monitor to
display the input connected to your NVR (HDMI or VGA).
Step 8. Use the Wizard for basic configuration setup
Power on the NVR. Normally, an Alibi logo splash screen appears within 2 minutes.

4www.Observint.com
© 2017 Observint Technologies. All rights reserved.
Model ALI-NVR3304P ALI-NVR3308P ALI-NVR3316P
Ethernet
1x 10/100 Mbps RJ-45 self-adaptive
Ethernet interface,
4 independent 10 /100 Mbps PoE
Ethernet interfaces
1x Gigabit RJ-45 self-adaptive
Ethernet interface,
8 independent 10 /100 Mbps PoE
Ethernet interfaces
1x Gigabit RJ-45 self-adaptive
Ethernet interface,
16 independent 10 /100 Mbps PoE
Ethernet interfaces
Power Over Ethernet Max Power: 40 W
Supported Standards: 802.3af, 802.3at
Max Power: 120 W
Supported Standards: 802.3af, 802.3at
Max Power: 200 W max output
Supported Standards: 802.3af, 802.3at
USB 2x USB 2.0 1x USB 2.0 (front panel),
1x USB 3.0 (rear panel)
1x USB 2.0 (front panel),
1x USB 3.0 (rear panel)
Hard Drive Interface 1x SATA 2x SATA 2x SATA
Hard Drive Capacity 1x HDDs max, up to 6TB capacity 2x HDDs max,
up to 6TB capacity each
2x HDDs max.,
up to 6TB capacity per HDD
Alarm Input Camera Dependent x4 (NVR) and Camera Dependent 4
Alarm Output Camera Dependent x1 (NVR) and Camera Dependent 1
Operating System Embedded Linux
Security Password Protection
Protocols TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS
IPv4, TCP/IP, UDP, HTTP, UPnP, RTSP/
RTP/RTCP, SMTP, FTP, DHCP, NTP, DNS,
ONVIF, HTTP multipart
Power Requirements 48 Vdc 100~240 Vac ≤ 180 W 100 ~ 240 Vac ≤ 300 W
Power Consumption ≤ 10 W (without HDD) ≤ 15 W (without HDD) ≤ 15 W (without HDD or PoE enabled)
Weight 2.2 lbs. (without HDD) 6.6 lbs. (without HDD) 6.6 lbs. (without HDD)
Dimensions (in.) 12.4” W × 9.1” D × 1.8” H 15.0” W × 11.4” D × 1.8” H 15.2 W” × 12.4” D × 2.0” H
Operating Temperature 14°F ~ 131°F
Color / Material Black
Material Aluminum
Approvals CE, FCC, RoHS, UL
Remote Client System Requirements
Operating System Microsoft Windows XP, Vista, 7, 8, 10 (32-bit and 64-bit version)
Apple MacOS X 10.5 (Intel x86 only), 10.6 and 10.7
Microsoft Windows 2000, 2003, XP,
Vista, 7, 8, 10 (32-, 64-bit version) /
Apple MacOS X 10.5 and above
Web Browser Microsoft Internet Explorer 8.0, 9.0, 10, and 11 (32-bit version), Safari 5 and higher
Software Requirements Web Component Installation
Mobile Client OS Platform iOS, Android (Alibi Witness)
If ID Authentication is not disabled (see the Menu | Conguration | General settings), a login window will open. In the Login window,
select a User Name with administrative privileges, enter its password, then click OK. A window of Menu icons will open.
For additional information about using your system, refer to the ALIBI Embedded Network Video Recorder Firmware V3.4.x User
Manual provided electronically with your system.
Specications
Model ALI-NVR3304P ALI-NVR3308P ALI-NVR3316P
Number of Channels Supported 4 8 16
Compression Format Supports H.265/H.264/H.264 OVC Supports H.265/H.264/
H.264 OVC, MPEG4
Recording Performance 40 Mbps max 80 Mbps max 160 Mbps max
Remote Viewing Output Capacity 80 Mbps max 160 Mbps max 160 Mbps max
Supported Frame Rate per Channel Main stream: Up to 60 fps
Sub-stream: Up to 60 fps --
Recording Type Continuous, Schedule, Event, Motion Detection, VCA Continuous, Schedule, Alarm,
Motion Detection, Event
Supported IP Camera Resolution 8MP / 6MP / 5MP / 4MP / 3MP / 1080p / UXGA / 720p / VGA / 4CIF / DCIF / 2CIF / CIF / QCIF
Supported Playback Resolution 8MP / 6MP / 5MP / 4MP / 3MP / 1080p / UXGA / 720p / VGA / 4CIF / DCIF / 2CIF / CIF / QCIF
Synchronous Playback 4-ch @ 1080p 2-ch @ 4K, or 8-ch @ 1080p 2-ch @ 4K, 8-ch @ 1080p
Video Output VGA, HDMI
HDMI Video Output Formats
4K (3840 × 2160)/30 Hz,
1920 × 1080/60 Hz,
1600 × 1200/60 Hz,
1280 ×1024/60 Hz,
1280 × 720/60 Hz,
1024 × 768/60 Hz
4K (3840 × 2160)/60 Hz,
4K (3840 × 2160)/30 Hz,
2K (2560 × 1440)/60 Hz,
1920 × 1080/60 Hz,
1600 × 1200/60 Hz,
1280 × 1024/60 Hz,
1280 × 720/60 Hz, 1024 × 768/60 Hz
VGA Video Output Formats
1920 × 1080/60 Hz, 1600 × 1200/60 Hz,
1280 × 1024/60 Hz,
1280 × 720/60 Hz, 1024 × 768/60 Hz
1920 × 1080/60Hz,
1280 × 1024/60Hz,
1280 × 720/60Hz, 1024 × 768/60Hz
Two Way Audio Input 1-ch, RCA (Linear, 1kΩ)
Audio Output 1-ch, RCA (Linear, 1kΩ)
Export Formats MPEG4 .MP4, .AVI

5www.Observint.com
Holes and slots for
HDD screws
HDD power cable
HDD SATA cable
Front panel cables
PC board
Back
Front
If your recorder was received without an HDD installed, the HDD power cable and SATA cable may or may not be plugged into the PC
board.
4. Unpackage the HDD you are installing in the chassis, and then place it underside up on a clean, electrostatic-free surface. Follow the
ESD guidelines described above.
HDD mounting
screw holes
5. Screw the four HDD mounting screws provided into the holes on the underside of the HDD until the screw heads are about
1/8 inch above the surface.
6. Position the HDD in the recorder chassis with the HDD mounting screws fully seated in the holes and slots in the bottom of the chassis.
The HDD should be above the front panel ribbon cable, and under the front panel black cable. See the photo above for the location of
these cables.
APPENDIX A HDD Installation
The following procedures illustrate hard disk drive (HDD) installation in a recorder without an HDD, and installation of a second HDD. If you
purchased your NVR without a HDD, or you want to replace the HDD installed in your NVR or add another, use this procedure as a guideline.
NVR compatible HDDs
For the best performance of your system, install only a high-reliability security grade HDD, such as Western Digital® Purple series or
GreenPower™ series HDD. Security grade HDDs are designed to stream video eciently and have a very low failure rate.
The NVR can accommodate one HDD (ALI-NVR3304P) or two HDDs (ALI-NVR3308P and ALI-NVR3316P), each with a capacity up to 6TB.
HDD Installation - ALI-NVR3304P
Cables and screws needed to install the HDD are provided.
CAUTION

Follow recommended electrostatic discharge (ESD) guidelines while performing this procedure. Install the HDD in a static-free
environment, wearing a certied ESD wrist strap. If a static free environment and ESD wrist strap is not available, touch the bare metal of
the NVR chassis frequently when installing the drive to dissipate the static charge naturally generated on your skin and clothing and avoid
touching electronic components.
1. Power o the NVR, if necessary, then disconnect the power adapter and all other cables from the recorder.
2. Remove the top cover from the NVR by removing the six cover screws. Two cover screws are located on each side, and two are located
on the back. See the drawing below. Save the screws for use later.
3. The photo below shows the inside of the recorder without an HDD. Become familiar with the items identied in the photo.
© 2017 Observint Technologies. All rights reserved.

6www.Observint.com
© 2017 Observint Technologies. All rights reserved.
8. Turn the chassis over, and then attach the HDD power cable and SATA cable to the mating connectors on the HDD and PC board. These
connectors must be fully seated.
9. Reinstall the NVR cover using the cover using the screws removed earlier.
10. During the NVR initialization, follow the options in the Wizard to initialize/reformat the HDD. You can also initialize the HDD using
the Menu | HDD feature. For more information, refer to the ALIBI Embedded Network Video Recorder Firmware V3.4.x User
Manual available for download from your vendor.
11. Initialize (Init) the HDD when you setup the NVR using Wizard.
HDD Installation - ALI-NVR3308P and ALI-NVR3316P
The recorder will accommodate one or two internal HDDs. If your recorder doesn’t have an HDD installed, use this procedure to install an HDD.
The HDD mounting screws and HDD cables are provided with your recorder.
CAUTION

Follow recommended electrostatic discharge (ESD) guidelines while performing this procedure. Install the HDD in a static-free
environment, wearing a certied ESD wrist strap. If a static free environment and ESD wrist strap is not available, touch the bare
metal of the NVR chassis frequently when installing the drive to dissipate the static charge naturally generated on your skin and
clothing and avoid touching electronic components.
1. Disconnect all cables from the recorder, and then set the recorder on a clean, static free surface, top up.
2. Remove the top cover from the recorder by removing the cover screws on the back of the chassis, and on each side. The screw
arrangement of your NVR may be dierent than that shown in the drawing below.
7. While holding the HDD in place in the chassis, turn the chassis over, and then ensure that the mounting screws are fully seated in the
mounting screw slots as shown in the photo below. Tighten the HDD mounting screws until snug. Be careful to not over-tighten the
screws.

7www.Observint.com
© 2017 Observint Technologies. All rights reserved.
5. Un-package the HDD. In the photo below, note the location of the HDD mounting screw holes on the underside of the HDD. Also
shown are the SATA and Power cable connectors.
SATA cable
connector
Power cable
connector
HDD mounting
screw holes
6. Screw the four HDD mounting screws into the mounting screw holes until the screw heads are about 1/8 inch from the surface of the
HDD.
CAUTION

Follow recommended electrostatic discharge (ESD) guidelines while performing this procedure. Install the HDD in a static-free
environment, wearing a certied ESD wrist strap. If a static free environment and ESD wrist strap is not available, touch the bare metal of
the NVR chassis frequently when installing the drive to dissipate the static charge naturally generated on your skin and clothing and avoid
touching electronic components.
7. Position the HDD in HDD bay 1 such that the HDD cable connectors are toward the middle of the chassis and the HDD mounting
screws are fully seated in the mounting screw slots.
3. Orient the chassis as shown in the picture below. Become familiar with the locations of the HDD mounting screws for HDD 1 (initial
HDD) and HDD 2 (second HDD), and the location of the HDD 1 SATA connector on the PC board.
Back PC board
HDD 1 SATA data
cable connector
HDD power
cable connector
HDD 2 SATA data
cable connector
HDD bay 1 HDD bay 2
SATA power cable
assembly
SATA data
cables (2)
Front panel
cables
Slots for HDD
mounting
screws (4 x 2)
4. If the SATA power cable assembly and the SATA data cables provided are not plugged into the PC board, plug them into the board as
shown above.

8www.Observint.com
© 2017 Observint Technologies. All rights reserved.
13. Check all the HDD cable connectors to verify they are fully seated, and then reinstall the NVR top cover.
14. When powering on the NVR, us the Alibi Wizard to initialize (Init) the HDD(s).
8. While holding the HDD in place, carefully turn over the chassis with the HDD and then tighten the mounting screws to secure the HDD.
Be careful not to overtighten the screws.
HDD 1 mounting screws
9. Turn the chassis over so the top is up.
10. Attach the SATA data cable that is plugged into the HDD 1 SATA data cable connector to the HDD 1 SATA data connector. When the
connector is fully seated, it clips into place. See the photo below.
11. Plug either HDD power cable connectors into the SATA power cable connector on the HDD.
12. If you are installing a second HDD in the chassis, follow steps 7 through 11 above to position, secure and cable the second HDD in HDD
bay 2. See the photo below.