ALLEN & HEATH XONE:DB2 User manual

QUICK-START
GUIDE
ALLEN & HEATH
XONE:DB2

Installation and Setup
To activate Serato DJ with the Allen & Heath XONE:DB2 it requires a
Serato DJ license to be purchased and activated on your user account. The
XONE:DB2: DB2 also requires the DVS Expansion Pack to be purchased
and activated before unit can be used with NoiseMap™ control tone to
control DVS playback. You can purchase both products here.
The Allen & Heath XONE:DB2 requires drivers on both Mac OS X and
Windows. Please make sure you have the latest drivers installed. It is
always important to connect your mixer directly to your computer, rather
than a USB hub. Please also ensure you have installed the latest available
version of Serato DJ.
To use the DVS Expansion Pack with the XONE:DB2 you will need to follow
the steps in the DVS Control section.

MAIN MIX OUT RECORDOUTB OOTH OUT ANALOGUEIN
DIGITALIN
LEFT RIGHT
1
2
3
# XONE:DB2 Control Function
1 AC POWER IN Connect a power cable to your mixer
2 ON/OFF Turn the mixer On/Off
3 MAIN MIX OUT Connect balanced XLR cables to the main mix out
4 RECORD OUT Connect RCA cables to the record out
5 BOOTH OUT Connect Balanced TRS cables to booth out
6 ANALOGUE IN Connect input sources
7 INPUT SOURCE SWITCH Select PH (Phono) for Phono input devices, select LN (Line) for Line input devices,.
8 GROUNDING POST Connect turntable grounding wires
9 USB 2.0 Connect USB cable to your computer
10 X-LINK Connect X-Link cable to other Allen & Heath devices
11 RECORD DIGITAL OUT Connect digital cables to record out
12 DIGITAL IN Digital device inputs for each channel
4 5 6 7
12 11 10 9
8
MIXER

1
2
3
11
4 65
7
8
9
10
#XONE:DB2 Function
1 HEADPHONE SECTION Headphone output and controls
2 MIDI SHIFT Used in conjunction with XONE:DB2 midi
controls
3 MIC SECTION Microphone input and controls
4 INPUT SELECT Select channel input source
5 CHANNEL CONTROLS Control and monitor channel volume and
EQ controls
6 OUTPUT METER Displays output volume
7 MIX Control Mix output volume
8 BOOTH Control Booth output volume
9 MENU Access the XONE:DB2 Menu
10 FX SECTION AND
DISPLAY
FX-X and FX-Y Controls. XONE:DB2
information is shown on the LCD display.
11 CROSSFADER Fade audio between channels
XONE:DB2 User Guide
For further information on XONE:DB2 controls and details on individual
Menu features please refer to the Allen & Heath XONE:DB2 Hardware User
Guide.
Download the XONE:DB2 User Guide from the Allen & Heath website here.

DVS Control
To use the Allen & Heath XONE:DB2 mixer with DVS control and Serato DJ,
you will rst need to own a Serato DJ license and a DVS Expansion Pack
license (these two products have been bundled together as the Club Kit).
Click here to purchase the Club Kit
Once you have purchased and activated the Club Kit (or individual licenses
separately) follow the steps below to get DVS control working with your
Allen & Heath XONE:DB2 mixer.
Install Drivers
Connect your mixer and open the latest version of Serato DJ. You should
see an ‘INSTALL DRIVER’ dialogue box appear in the right hand side-
panel. Click ‘INSTALL DRIVER’ and follow the installer prompts. If you don’t
have the supported hardware with you right now you can still download the
driver from the hardware manufacturers website.
Select Input source
Once your turntables or CDJs are connected to the mixer, check that you
are using the correct Input setting on the back of the mixer. If you have
connected an analogue source (turntables), make sure you have the input
set to PH (Phono), if you have connected a digital source (CDJs) make sure
it is set to LN (Line) accordingly.
NOTE: If you want to connect an analogue source to channels 1 or 4, you
will notice there is no switch on the rear of the mixer and will need to
enable the hardware preamp for those channels. See the XONE:DB2 user
guide for more information.
Select Primary Decks
Open the SETUP screen and click the AUDIO tab, here you will need to
select your Primary Decks.
Choosing Channel 1 and 2, will allow you to have a traditional 1-2-3-4
channel conguration. Choosing Channel 2 and 3 will allow you to have
a 3-1-2-4 conguration (from left to right across the mixer).
Select which deck conguration you are using with the mixer and change
if necessary. If you notice you are getting signal from your control tone but
on the wrong deck, you might need to double-check your Primary Decks in
the SETUP screen or the physical inputs on the back of the mixer.
You are now set up to use your mixer with Serato DJ and DVS control
using the REL or ABS control modes. Refer to the Serato DJ manual for
more information on Control Modes.

Using the Tool Tips
Click on the icon to enable Tool Tips. This is located in between the
MIDI and setup button in the top right hand corner of the screen. Tool Tips
provide a handy way to learn the various features of Serato DJ.
Move the mouse over a section of the screen to bring up a context sensitive
tool tip. Holding the mouse over the button with Tool Tips turned on
will show you a list of all keyboard shortcuts.
For more information about how to use Serato DJ, please go to our website
www.serato.com or download the Serato DJ Manual.
For more information on your XONE:DB2, please refer to the Allen & Heath
XONE:DB2 manual.
Recording
To record your mixes with Serato DJ and the XONE:DB2 you will need to set
up the mixer for recording. Designate a channel to use for recording and then
select this channel in the Serato DJ REC panel. This will allow you to record
the software mix.
Designating a channel is done from the XONE:DB2 hardware using the Menu
button and Display Screen. Select ‘USB Routing’ from the Menu and select
‘Record’ on the channel you want to designate for recording. You will not
be able to use this channel in Serato DJ while it is selected as a recording
channel.
If you wish to record the video output, Serato Video output will only be sent
to Channel 4. To record the video + audio mix you will need to make sure
you have selected Channel 4 as your dedicated recording channel. See the
XONE:DB2 User Guide for more information on Routing and Menu features.
MIDI
The MIDI feature in Serato DJ provides the ability to remap Serato DJ
software functions to your primary Serato DJ controller, interface or mixer.
You can also assign controls to a secondary MIDI controller to further
enhance your performance.
For more information on MIDI mapping with Serato DJ click here.
To remap your supported Serato DJ device, open the SETUP screen and
click the MIDI tab. If your Serato DJ device supports hardware remapping it
will show up in the MIDI Devices list at the top.
Select your connected device from the MIDI Devices list and make sure the
“Enable MIDI device” option is checked.
Once checked, the MIDI assign button at the top of the screen will become
available for you to start remapping.
You can save, edit or delete MIDI presets in the MIDI tab of the SETUP
screen. Clicking ‘Restore Defaults’ will erase any custom mappings for all
connected devices and revert their functions back to default.
Download the Serato DJ software manual for further information.
NOTE: Ofcial Serato Accessories do not currently support user remapping.
Hardware features that cannot be remapped at this stage are Jogwheels/
Platters, Input Switches, Shift buttons and Performance Pad Mode buttons.
Re-mapping any pad(s) in Hot Cue mode will also re-map the same pad in
Saved Flip mode and vice versa.