ALLEN & HEATH SYS-LINK W312/16-SLV2 Kit User manual

WZ316:2 / WZ312:2 / WZ320S SYS-LINK Option Fitting Instructions AP5735 1
These are the instructions for fitting the SYS-LINK Version 2 console expander option to the MixWizard
WZ316:2, WZ312:2 and WZ320S consoles. Two consoles, each with SYS-LINK V2 installed, may be linked
together using a single 37 way cable such that one becomes a channel expander (slave) to the other
(master). This links all the mix buses and the PFL/AFL system. The WZ316:2, WZ312:2 and WZ320S have
an output connector only and should therefore be used as a slave. The cable is not supplied but may be
ordered separately or sourced elsewhere. Fitting the option requires removal of the rear connector cover
to access the internal assemblies, installation of a circuit card assembly and ribbon harness, and some
soldering. This work should be carried out by technically competent personnel.
For information on how to use SYS-LINK please refer to the Applications Note AP5736. For information
on using the WZ316:2 and WZ312:2 consoles refer to User Guide AP5331. For information on using the
WZ320S console refer to User Guide AP6318. Should further assistance be required, please contact Allen
& Heath Technical Support (details on our web site www.allen-heath.com).
Before Starting
Read these fitting instructions carefully before starting. For trouble free installation and operation heed all
the precautions noted. The console must be fully unplugged and removed from its rack, plinth or other
furniture before carrying out the work. Normal workshop tools are required. These include Pozi
(crosshead) and Torx (starhead) screwdrivers, and a fine tipped soldering iron. Provide a suitably large,
well lit work surface such as a service workshop bench. To avoid damage to the cosmetics of the
console ensure that the work surface is clean and clear of obstructions. Allow enough time to carry out
the work properly and test the results.
Check the Contents
The following parts are packed with the kit:
003-260 x1 SYS-LINK V2 circuit assembly
with power harness. The panel fixing nuts are
fitted to the D-connector socket.
AL5489 x1 2-connector IDC ribbon harness
AP5736 x1 SYS-LINK V2 Applications Note.
IMPORTANT:Any changes or modifications
to the equipment not approved by Allen & Heath
could void the compliance of the equipment.
Whilst we believe the information in these
instructions to be reliable we do not assume
responsibility for inaccuracies. We also reserve
the right to make changes in the interest of
further product development.
Copyright© 2005 Allen & Heath Limited. All rights
reserved. www.allen-heath.com
This work should be carried out by
competent technical personnel only.
Disconnect the mains power cord before
opening the unit.
Take care not to damage the panels or
internal assemblies during fitting. Prevent
loose parts or dirt from entering the console
as this may cause equipment failure.
ALLEN&HEATH WZ316:2 / WZ312:2 / WZ320S SYS-LINK AP5735 issue 2
Fitting Instructions for the W312/16-SLV2 Kit
Option fits here
IT IS RECOMMENDED THAT THIS OPTION IS FITTED BY AN APPROVED ALLEN & HEATH SERVICE AGENT

2 WZ316:2 / WZ312:2 / WZ320S SYS-LINK Option Fitting Instructions AP5735
Fitting Instructions
Step 1: Preparation
Ensure the console is powered off. Disconnect
the mains power lead and all connected cables.
Remove the console from its rack or other
furniture and place on the work surface.
Step 2: Open the connector panel
Start by removing the side trims if fitted: four
M4x10 Pozi screws per side.
Remove the two M3x6 Torx screws from each
side of the connector panel. Remove the six
M3x6 Torx screws from the rear of the connector
panel. Carefully tilt the connector panel away
from the console so that it is flat on the work
surface.
Step 3: Remove the blanking plate
Remove the two blanking plate screws from the
rear of the connector pod. Remove the
blanking plate.
Step 4: Fit the SYS-LINK card
The SYS-LINK circuit card assembly is fixed to
the connector panel using two D-type connector
nuts. These are supplied already fitted to the
card’s socket. Remove the nuts and place the
card into the connector panel slot, observing the
correct orientation. Secure the SYS-LINK card
by refitting the D-type nuts, ensuring that they
are fully tightened.
Step 5: Connect the SYS-LINK power
The option gets its power from the console
supply rails. Hand solder the SYS-LINK pcb
sleeved red, black and green wires to the
connector pcb: red to pin +15V, black to pin -
15V and green to pin SGND. Check that the
solder joints are of good quality.
Step 6: Plug in the IDC harness
Plug one end of the supplied IDC harness into
header CN1 on the SYS-LINK card. Plug the
other end into the corresponding IDC header on
the connector card: CN7 on the WZ316:2 and
WZ320S or CN222 on the WZ312:2.
Step 7: Refit the connector panel
Check your work and ensure that there is no dirt
or debris inside the connector pod. Ensure that
all IDC harnesses are correctly inserted and
positioned. Carefully refit the connector panel
to the console, making sure not to trap and
possibly damage the SYS-LINK card’s IDC and
power harnesses. Replace the ten M3x6 Torx
screws - six at the rear of the connector panel
and two at each side. Refit the side trims if
required using the four M4x10 Pozi screws.
Step 8: Test
With all panels refitted, connect to the mains
supply. Power on and check for correct
operation
CN1
CN7
IDC AND POWER HARNESS FITMENT - WZ³16:2 / WZ³20S
CN1
SGND
+15V
-15V
DGND
ALLEN&HEATH
SINGLE
INTERNAL
AUX5
AUX6
FX
EXTERNAL
-
R
EFFECT
EFFECT
DUAL
1-16
EFFECT
1-8
9-16
L/M
ST1 -
+
+
L
R
MIX
-IN
+IN
3
INPUT
21
RING-INRING
TIP +INTIP LINE
MIC
LINE IN/OUT
TIP
RING
SEND
RETURN
XLROUT
-OUT
3
21
INSERT
+OUT TIP+
RING-
MIDIINFOOTSWITCH
FXMUTE FX EDIT
MixWizard WZ316:2
1INSERT2
1
MIC
LINEIN
OUT
DIRECT
3INSERT
2
MIC
OUT
3
MIC
LINE IN
DIRECT
OUT
INSERT
DIRECT
LINEIN
4INSERT
4
DIRECT
OUT
LINE IN
MIC
5INSERT6
5
LINEIN
MIC
DIRECT
OUT
BACKUP SUPPLY
REFERTO USER GUIDE FORDETAILS.
ONLYUSE RECOMMENDEDALLEN&HEATHPOWER SUPPLY.
EXTERNALDC IN
Serial No.Made in the UK by A LLEN & HEATH Li mited
OFF
0 I
ON
T630mAL250V 20mm
FUSE
ACMAINS IN ~
100- 240V~ 47-63Hz 45W MAX
REFERSERVICING TOQUALIFIED SERVICEPERSONNEL.
REPLACEFUSE W ITH SAME TYPE AND RATING.CAUTION: FOR CONTINUEDPROTECTIONAGAINSTRISK OF FIRE
ATTENTIO N: RE MPLAC ER LE FU SIBL E AVEC UN DES ME MES CARACT ERISTIQ UES.
DONOT OPEN
CAUTION
RISKOF ELECTRICSHOCK
AVIS:RISQUEDE CHOCELECTRIQUE-NE PASOUVRIR.
WARNING: TO REDUCE THE RISK OF ELECT RIC SHOCK DO NOT EXPOSE THI SA PPARATUS TO R AIN OR MOIST URE.
WARNING: THIS APP ARATUS MUS T BE EARTHE D
INSERT 7
67
LINE IN
MIC
DIRECT
OUT
8INSERT
8
DIRECT
OUT
LINEIN
MIC
INSERT
DIRECT
OUT
LINEIN
MIC
87654321
INSERT
10
9
LINEIN
MIC
DIRECT
OUT
11INSERT
11
LINEIN
MIC
DIRECT
OUT
INSERT
10
DIRECT
OUT
LINEIN
MIC
1213 INSERT
OUT
12
DIRECT
LINE IN
MIC
INSERT
14
13
MIC
LINEIN
OUT
DIRECT
14
MIC
OUT
15INSERT
15
MIC
LINE IN
OUT
DIRECT
16INSERT
16
MIC
LINEIN
OUT
DIRECT
L
R
L
R
INSERT
INSERT
DIRECT
LINEIN
1SEND2AUX3AUX AUXAUXAUX 5AUXINST1 6 4
L
IN
R
L
/MONO
R
ST2AB
A
B
SYS-LINKOUT (option)
OUT
M/MONO
16 15 14 13 12 11 10 9
9
REMOVE 6x M3 TORX SCREWS
REMOVE SIDE TRIMS
REMOVE 2x M3 TORX SCREWS PER SIDE
REMOVE 4x M4 POZI SCREWS PER SIDE
/MONO
M
OUT
SYS-LINK OUT ( option )
B
A
AB ST2
R
/MONO
L
R
IN
L
ST1 IN
EXTERNAL
AUX6
AUX5
INTERNAL
INTERNAL
AUX5
AUX6
EXTERNAL
INST1
L
IN
R
L
/MONO
R
ST2AB
A
B
SYS-LINK OUT ( option )
OUT
M/MONO
IDC AND POWER HARNESS FITMENT - WZ³12:2
CN222
CN1
CN1
RED BLACK
GREEN
-15V+15V
SGND
CN1 WZ316:2 SHOWN,
OTHERS SIMILAR