Allen-Bradley 140G-G User manual

Installation instruction for 140G-G, 140MG-G
Istruzioni di installazione
Installationsanleitung
Instructions pour l’installation
Instrucciones de instalación
Bul. 140G/140MG
DIR 1000719R0001 Version 02
DIR 1000719R0001 Version 02 - 140G-G_ ; 140MG-G_
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
CLACK
from 0.51" to 0.55"
from 13 mm to 14 mm
0.13"ø
ø 3.5 mm
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件に従ってください）
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物
1
x2
3p
4p
x3
x2
x3
x2
x3
x4
x6
x6
x8
x2
x2
x2
x2
x1
x1
Phase
barrier
End cap kit Carter Insulator Side
cover
Insulator
CH 5
CH 7
140G-G-MH3
140G-G-MH4
140G-G-PB3M
140G-G-PB4M
Mounting hardware
LENGTH M
73 mm (2.87" ) M 4
M
M 4
LENGTH M
1 4 mm (0.55" ) M 6
LENGTH ø
1 2 m m (0.47") 3

- Use cable or insulated busbars/ or perform specific type test on the installation.
- Usare cavi o barre isolate/ o eseguire prove di tipo specifiche sull' installazione.
- Kabel oder isolierte Sammelschienen verwenden/ oder die spezifische Typprüfung auf derInstallation durchführen.
- Utiliser un câble ou des barres isolées/ ou réaliser un test de type spécifique sur installation.
- Utilizar un cable o barras aisladas/ o efectuar una prueba de tipo específico sobre instalacíon.
(2)
1
2
Maximum recommended conductor support distance
DIR 1000719R0001 Version 02
7.87"/200 mm7.87"/200 mm

(3)
DIR 1000719R0001 Version 02
3
1
2
4
OK
0.98"/25 mm0.98"/25 mm
3
1,1 Nm
8,9 lb-in
4.21"/107 mm
Ø 0.18"
Ø 4.5 mm-M4
B
D
E
C
A
X
X
Y
Y
Y
Y
X
X
IV ONLY
IV ONLY
IV ONLY
IV ONLY
0.49"/12.5 mm
0.49"/12.5 mm
1.97"/50 mm
2.11"/53.5 mm
IV ONLY
NOT REQUIRED FOR
IEC APPLICATIONS
MANDATORY FOR
UL APPLICATIONS
A B C D E
III-IV 3.11"
79 mm
1.69"
43 mm
1.85"
47 mm
0.59"
15 mm
0.93"
23.5 mm
III 2.79"
71 mm
1.85"
47 mm
2.87"
73 mm
0.67"
17 mm
1.44"
36.5 mm
IV 2.79"
71 mm
1.85"
47 mm
3.86"
98 mm
0.67"
17 mm
1.44"
36.5 mm
III 2.91"
74 mm
2.16"
55 mm
3.19"
81 mm
0.83"
21 mm
1.59"
40.5 mm
IV 2.91"
74 mm
2.16"
55 mm
4.17"
106 mm
0.83"
21 mm
1.59"
40.5 mm
WITH ESCUTCHEON
WITHOUT ESCUTCHEON
4
140G-G
140MG-G
7.5
6
A
0.29"
0.24"
A max
min 6,5
Ø min 6,5
0.14"(3.5) min
0.2"(5) max
Ø min 0.26"
max 0.63"
max 16
min 0.26"
Ø 6.5
16
Ø 0.26"
A
0.63"

140G-G THERMOMAGNETIC TRIP UNIT
*IEC ONLY
In
Fixed
Fixed
Fixed
Fixed
Type
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
500
100
110
125
160*
50
60
63
70
80
90
500
500
600
1600112Adjustable
30
32
35
I3
500
500
500
500
630
Min Med Max I3
500
500
136 160
I1
15
16
20
25
30
1250
110
125
32
35
40
50
60
63
700
800
900
1000
1100
Type
70
80
90
100
In
15
16
20
25
40
Fixed
Fixed
Fixed
Fixed
Fixed
1000
I1(A)
100
In=100A
I3(A)
5ONLY REQUIRED FOR THROUGH THE DOOR APPLICATION
(WITH DOOR OF THE PANEL ≤0.98"/25 mm FROM THE FRONT)
6
1
2
(4)
DIR 1000719R0001 Version 02

7
In A B C D E F G H I
3 from 4 In to 11 In 12 15 17 20 23 25 28 30 33
7 from 4 In to 11 In 28 34 40 46 53 59 65 71 77
15 from 3 In to 11 In 45 60 75 90 105 120 135 150 165
30 from 3 In to 11 In 90 120 150 180 210 240 270 300 330
50 from 3 In to 11 In 150 200 250 300 350 400 450 500 550
70 from 3 In to 11 In 210 280 350 420 490 560 630 700 770
80 from 3 In to 11 In 240 320 400 480 560 640 720 800 880
100 from 3 In to 11 In 300 400 500 600 700 800 900 1000 1100
125 from 3 In to 11 In 375 500 625 750 875 1000 1125 1250 1375
I3
- Manually trip the breaker prior to any adjustment of the magnetic trip settings.
- E’obbligatorio mettere l'interruttore in posizione Trip test prima di regolare il termomagnetico.
- Der Leistungsschalter muss vor Einstellung des thermomagnetischen Auslösers zwingend in die Prüfstellung geschaltet werden.
- Il est obligatoire de mettre le disjoncteur en position de Test de Déclenchement avant de régler le déclencheur magnétothermique.
- Es obligatorio situar el interruptor en posición “Test de Disparo” antes de realizar el ajuste del relé termomagnético.
CLACK
USE FLAT BLADE
SCREW DRIVER
140MG-G MAGNETIC ONLY TRIP UNIT
In=200A
FC D
B
E
H
G
A
I
HĊ ĂĖ Å
F G H I
800 900 1000 1100
A B C D E
300 400 500 600 700
2
1
DIR 1000719R0001 Version 02 (L9694) - B0301
Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN076C-MU-P - September 2015
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page