Allen-Bradley 9 Series User manual

M20A03-ML080QT8520MS
1
M L 0 8 0 QT8 5 2 0 M S INSTALL GUIDE
LCD upgrade kit
FOR YOUR ALLEN-BRADLEY SERIES 9 (8520MOP)
MONOCHROME

M20A03-ML080QT8520MS
2
IMPORTANT:
WARRANTY
Before using any MONITECH product please carefully
review this Manual as well as any additional
documentation provided with your shipment.
Attempting any of the following will void product warranty:
•unauthorized repairs or parts replacement
•inappropriate use or placement: exposing product to
liquids, harmful gases, electrical shock, physical
shock, temperatures beyond the range of -4°F to
140°F
(-20°C to 60°C)
•use of electrical voltage other than 12V 4.16A
(power supply and AC cable provided)
•Removal or modification of serial, product, or
warranty labels.
WARNING
ELECTRICAL HAZARD
DO NOT OPEN
TO AVOID ELECTRICAL SHOCK DO NOT
OPEN PRODUCT CASING. UNAUTHORIZED
REPAIRS OR PARTS REPLACEMENT ARE
PROHIBITED AND WILL VOID PRODUCT
WARRANTY. PLEASE RETURN TO
MONITECH FOR REPAIRS.

M20A03-ML080QT8520MS
3
REMOVAL:
Step #1) Turn off turn off main power, turn off machine.
Step #2) On the front of your machine, remove the screws holding the HMI
in place. Take out the HMI and keep the screws for re-installation. You will
have to unplug the video cable and the other cables to take out the HMI.
Please take a picture of your connection so you know where they go for re-
installation.
Step #3) This is what you got. Unscrew the fasteners holding the CRT
Frame to the HMI, keep the screws for re-installation. Unplug the power
connector from the board. An unscrew to the ground wire from the frame,
screw the power supply ground back in. After this take out the CRT Frame
from the HMI.
To see the CRT
and controller you
must remove the
back panel by
unscrewing the
screws hold it.
Screw to remove to
free the CRT frame
from the HMI
Unplug the
monitor power
from the board.
Unscrew the ground
wire from the board.
Re-attach the power
supply ground.

M20A03-ML080QT8520MS
4
Remove the
Anode Lead Cap
squeezing the
metal pins in
with a flat head
screwdriver.
Step #4) First discharge the CRT, it has high voltage. Be careful. Put a flat
head screw driver underneath the anode lead cap so it is touching the metal
part.
And get another screwdriver and cross it with the flat head used and touch
the metal frame with it. After a minute take the Anode lead Cap off or unplug
it from the driver board of the CRT.
Step #5) Unplug the Neck Board then Unscrew the CRT from the frame
(keep fasteners for re-installation). Push the CRT out of the frame and then
Unplug the Yoke & Unscrew the Ground from the Yoke.
Remove
the
Neck
Board
Unscrew the
four screws
holding the
CRT. Keep
these.
Unplug the Yoke and the
Unscrew the Yoke Ground
from the Frame.

M20A03-ML080QT8520MS
5
Step #6) Now that the CRT is out you are able to remove the
driver board by unscrewing the screws holding the board in
place.
INSTALLATION:
Step #7) Put Monitech’s Monitor in the housing using the four
screws previously holding the CRT in place.
With the
screwdriver fasten
the 4 screws to
attach the New
Monitech Monitor
on these 4 holes.

M20A03-ML080QT8520MS
6
Step #8) Place the CRT Frame with Monitech Monitor assembly back into
your HMI by using the screws previously mounting the frame in place.
Step #9) Open up your MK068 box, get MAV576 (Adaptor VGA to 15 PIN
LD Video Connector. Plug the VGA into the Monitech Monitor and tighten the
screws. Then plug your video cable from your machine into our adaptor.
Step #10) For the power connection there is 3 options.
Option 1) Get MAP302 out of the kit. This is the power connection to a wall
AC power, but if you want the power from your machine, cut the plug side
and strip the wires. Then place the wires onto the AC portion of the
terminals. Then you can attach to MAP307 and plug the jack side to the
Monitor.
MAV576
VGA goes to the
Monitech Monitor.
15 PIN LD does to
your controller
video cable.
Connect the MAP302 to
the power bar (MAP307),
then plug the power jack
into the monitor.
Connect the Ground and
LAN wires of MAP 302 to
the terminal.
MAP302,
Cut here
and strip
wires.

M20A03-ML080QT8520MS
7
Option 2) Cut the jack part of the MAP307 (Power supply) and strip the 2
wires. Solder or use butt connectors to connect the red wire to controller to
red wire of jack. Solder or use butt connectors to connect the black wire to
controller to black wire of jack. Then plug the jack into the monitor.
Option 3) Attach MAP302 (Power Cord) and MAP307 (Power Supply).
Connect the jack to the Monitor. Plug in MAP302 to an AC Wall Outlet.
Step #11) Before Mounting the HMI back into the machine. Turn On power
and Main Power to test the Monitor. If Video is on use the User Guide to
Adjust the Screen. Then mount the HMI back into the machine.
Enjoy your rejuvenated display!!! From the Monitech Family we
thank you for business.
Black is 0 VDC. Cut the
connector off it strip the wire
then use a crimp to attach to
the Black wire on MAP323
Red is 12 VDC. Cut the
connector off it strip the wire
then use a crimp to attach to
the red wire on MAP323
MAP307
MAP302

M20A03-ML080QT8520MS
8
For Technical Support, Call
1-877-493-6105
[e-mail]
20 Howard Place
Kitchener, Ontario N2K 4Z4
CANADA 519.725.222