Alliance Laundry Systems UT025 Owner's manual

Programming
Drying Tumblers
Refer to page 3 for Model Numbers
Part No. 70381401R5
February 2008
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
70381401 1
Installation must conform with local codes or in the absence of local codes with:
In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/NFPA 54
“National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.”
In Canada, installation must comply with Standards CSA B149.1 or Natural Gas and Propane Code CSA C22.1,
latest edition, Canadian Electric Code, Part I.
In Australia, installation must comply with the Australian Gas Association Installation Code for Gas Burning
Appliances and Equipment.
IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the
user smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the
above safety information must be posted in a prominent location near the tumbler for customer use.
FOR YOUR SAFETY, the information in this
manual must be followed to minimize the
risk of fire or explosion or to prevent
property damage, personal injury or death.
W033
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
– Do not try to light any appliance.
– Do not touch any electrical switch; do
not use any phone in your building.
– Clear the room, building or area of all
occupants.
– Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
– If you cannot reach your gas supplier,
call the fire department.
• Installation and service must be
performed by a qualified installer, service
agency or the gas supplier. W052
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance. W053
POUR VOTRE SÉCURITÉ, les informations
de ce guide doivent être respectées afin de
réduire les risques d’incendie, d’explosion
ou d’éviter les dommages matériels,
personnels ou blessures mortelles. W033R3QU
• Ne pas entreposer ou utiliser d’essence
ou toutes autres vapeurs et liquides
inflammables à proximité de cette
machine ou de tout autre appareil.
• QUE FAIRE EN CAS D’ODEUR DE GAZ :
– Ne pas mettre d’appareil en marche.
– Ne pas toucher aux interrupteurs
électriques ; ne pas utiliser le
téléphone des lieux.
– Évacuer la pièce, le bâtiment ou la zone
de tous les occupants.
– Appeler immédiatement le fournisseur
de gaz de la maison d’un voisin.
Respecter les instructions
communiquées par le fournisseur.
– Si vous ne pouvez pas joindre le
fournisseur de gaz, appeler le service
d’incendie.
• L’installation et l’entretien doivent être
effectués par un installateur, service
d’entretien qualifiés ou par le fournisseur
de gaz.
W052R5QU
MISE EN GARDE
POUR VOTRE SÉCURITÉ
Ne pas entreposer ou utiliser d’essence
ou toutes autres vapeurs et liquides
inflammables à proximité de cette unité
ou de tout autre appareil. W053R2QU

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
© Published by permission of the copyright owner.
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
270381401
Table of
Contents
Introduction......................................................................................... 3
Model Identification ............................................................................. 3
Customer Service.................................................................................. 5
Wiring Diagram .................................................................................... 5
Safety Information.............................................................................. 6
Important Safety Instructions ............................................................... 7
Programming the Electronic OPL Control...................................... 9
Introduction to Programming ............................................................... 9
Signal .................................................................................................... 10
Reversing .............................................................................................. 10
Status Lights ......................................................................................... 10
Automatic Dry and Condition Mode .................................................... 11
Time Dry and No Heat Modes.............................................................. 12
Custom.................................................................................................. 13
Custom Cycle Record ..................................................................... 13
Special Cycle Mode.............................................................................. 14
Special Time Mode............................................................................... 14
Security Lock-Out ................................................................................ 14
Show Mode........................................................................................... 14
Temperature Sensor .............................................................................. 15
Temperature Adjustment ...................................................................... 15
Temperature Display (°F/°C)................................................................ 15
Cylinder Temperature Display ............................................................. 15

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 3
70381401
Introduction
Model Identification
Information in this manual is applicable to these
models:
Gas Steam/Thermal Oil Electric
25 Pound
HA025L
HA025N
HT025L
HT025N
HU025L
HU025N
LA025L
LA025N
LT025L
LT025N
LU025L
LU025N
PA025L
PA025N
PT025L
PT025N
PU025L
PU025N
SA025L
SA025N
ST025L
ST025N
SU025L
SU025N
UA025L
UA025N
UT025L
UT025N
UU025L
UU025N
HT025S
HU025S
LT025S
LU025S
PT025S
PU025S
ST025S
SU025S
UT025S
UU025S
HT025E
HU025E
LT025E
LU025E
PT025E
PU025E
ST025E
SU025E
UT025E
UU025E
30 Pound
HA030L
HA030N
HT030L
HT030N
HU030L
HU030N
LA030L
LA030N
LT030L
LT030N
LU030L
LU030N
PA030L
PA030N
PT030L
PT030N
PU030L
PU030N
SA030L
SA030N
ST030D
ST030L
ST030N
SU030L
SU030N
UA030L
UA030N
UT030L
UT030N
UU030L
UU030N
HT030S
HU030S
LT030S
LU030S
PT030S
PU030S
ST030S
SU030S
UT030S
UU030S
HT030E
HU030E
LT030E
LU030E
PT030E
PU030E
ST030E
SU030E
UT030E
UU030E
35 Pound
AT035L
AT035N
HA035L
HA035N
HT035L
HT035N
HU035L
HU035N
LA035L
LA035N
LT035L
LT035N
LU035L
LU035N
PA035L
PA035N
PT035L
PT035N
PU035L
PU035N
SA035L
SA035N
ST035L
ST035N
SU035L
SU035N
UA035L
UA035N
UT035L
UT035N
UU035L
UU035N
AT035S
HT035S
HU035S
LT035S
LU035S
PT035S
PU035S
ST035S
SU035S
UT035S
UU035S
HT035E
HU035E
LT035E
LU035E
PT035E
PU035E
ST035E
SU035E
UT035E
UU035E
50 Pound
AT050L
AT050N
GT050L
GT050N
GU050L
GU050N
HA050L
HA050N
HT050L
HT050N
HU050L
HU050N
LA050L
LA050N
LT050L
LT050N
LU050L
LU050N
NT050L
NT050N
PT050L
PT050N
PU050L
PU050N
SA050L
SA050N
ST050D
ST050L
ST050N
SU050L
SU050N
UA050L
UA050N
UT050L
UT050N
UU050L
UU050N
AT050S
GU050S
HT050S
HT050T
HU050S
HU050T
LT050S
LT050T
LU050S
LU050T
PT050S
PT050T
PU050S
PU050T
ST050S
ST050T
SU050S
SU050T
UT050S
UT050T
UU050S
UU050T
AT050E
GU050E
HT050E
HU050E
LT050E
LU050E
PT050E
PU050E
ST050E
SU050E
UT050E
UU050E
Models continued on next page.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Introduction
70381401
4
Includes models with the following control suffixes:
OM – OPL micro RM – reversing OPL micro
(Continued)
Gas Steam/Thermal Oil Electric
55 Pound
HA055L
HA055N
HT055L
HT055N
HU055L
HU055N
SA055L
SA055N
ST055L
ST055N
SU055L
SU055N
UA055L
UA055N
UT055L
UT055N
UU055L
UU055N
Not Applicable
HT055E
HU055E
ST055E
SU055E
UT055E
UU055E
75 Pound
AT075L
AT075N
HA075L
HA075N
HT075L
HT075N
HU075L
HU075N
LA075L
LA075N
LT075L
LT075N
LU075L
LU075N
NT075L
NT075N
PT075L
PT075N
PU075L
PU075N
SA075L
SA075N
ST075D
ST075L
ST075N
STF75L
STF75N
SU075L
SU075N
UA075L
UA075N
UT075L
UT075N
UTF75L
UTF75N
UU075L
UU075N
AT075S
HT075S
HT075T
HU075S
HU075T
LT075S
LT075T
LU075S
LU075T
PT075S
PT075T
PU075S
PU075T
ST075S
ST075T
SU075S
SU075T
UT075S
UT075T
UU075S
UU075T
AT075E
HT075E
HU075E
LT075E
LU075E
PT075E
PU075E
ST075E
SU075E
UT075E
UU075E
120 Pound
AT120L
AT120N
HA120L
HA120N
HT120L
HT120N
HU120L
HU120N
LA120L
LA120N
LT120L
LT120N
LU120L
LU120N
PT120L
PT120N
PU120L
PU120N
SA120L
SA120N
ST120L
ST120N
SU120L
SU120N
UA120L
UA120N
UT120L
UT120N
UU120L
UU120N
WT120L
WT120N
XT120L
XT120N
XU120L
XU120N
AT120S
HT120S
HT120T
HU120S
HU120T
LT120S
LT120T
LU120S
LU120T
PT120S
PT120T
PU120S
PU120T
ST120S
ST120T
SU120S
SU120T
UT120S
UT120T
UU120S
UU120T
WT120S
WT120T
XT120S
XT120T
XU120S
XU120T
YU120S
YU120T
Not Applicable
170 Pound
AT170L
AT170N
HA170L
HA170N
HT170L
HT170N
HU170L
HU170N
LA170L
LA170N
LT170L
LT170N
LU170L
LU170N
PT170L
PT170N
PU170L
PU170N
SA170L
SA170N
ST170L
ST170N
SU170L
SU170N
UA170L
UA170N
UT170L
UT170N
UU170L
UU170N
WT170L
WT170N
XT170L
XT170N
XU170L
XU170N
AT170S
HT170S
HT170T
HU170S
HU170T
LT170S
LT170T
LU170S
LU170T
PT170S
PT170T
PU170S
PU170T
ST170S
ST170T
SU170S
SU170T
UT170S
UT170T
UU170S
UU170T
WT170S
WT170T
XT170S
XT170T
XU170S
XU170T
Not Applicable

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Introduction
5
70381401
Customer Service
If literature or replacement parts are required, contact
the source from which the machine was purchased or
contact Alliance Laundry Systems at [phone]
for the name and address of the nearest authorized
parts distributor.
For technical assistance, call [phone].
Wiring Diagram
The wiring diagram is located in the junction or
contactor box.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
670381401
Safety Information
Precautionary statements (“DANGER,” “WARNING”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer and those maintaining the
machine.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
IMPORTANT: Warranty is void unless drying
tumbler is installed according to instructions in the
Installation Manual. Compliance with minimum
specifications and requirements detailed herein,
and with applicable local gas fitting regulations,
municipal building codes, water supply regulations,
electrical wiring regulations, and any other
relevant statutory regulations. Because of varied
requirements, applicable local codes should be
thoroughly understood and all pre-installation
work arranged for accordingly.
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense, caution and carefulness are factors which
CANNOT be built into this tumbler. These factors
MUST BE supplied by the person(s) installing,
maintaining or operating the tumbler.
Always contact your dealer, distributor, service agent
or the manufacturer on any problems or conditions you
do not understand.
Indicates an imminently hazardous
situation that, if not avoided, will cause
severe personal injury or death.
DANGER
Indicates a hazardous situation that, if not
avoided, could cause severe personal
injury or death.
WARNING
Indicates a hazardous situation that, if not
avoided, may cause minor or moderate
personal injury or property damage.
CAUTION
Failure to install, maintain, and/or operate
this machine according to manufacturer’s
instructions may result in conditions which
can produce serious injury, death and/or
property damage. W051R1
WARNING

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Safety Information
7
70381401
Important Safety Instructions
Save These Instructions
1. Read all instructions before using the tumbler.
2. Refer to the Grounding Instructions for the
proper grounding of the tumbler.
3. Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, or other
flammable or explosive substances as they give
off vapors that could ignite or explode.
4. Do not allow children on or in the tumbler. This
appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
5. Before the tumbler is removed from service or
discarded, remove the door to the drying
compartment and the door to the lint
compartment.
6. Do not reach into the tumbler if the cylinder is
revolving.
7. Do not install or store the tumbler where it will
be exposed to water and/or weather.
8. Do not tamper with the controls.
9. Do not repair or replace any part of the tumbler,
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
10. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
11. To reduce the risk of fire, DO NOT DRY plastics
or articles containing foam rubber or similarly
textured rubberlike materials.
12. Always clean the lint filter daily.
13. Keep area around the exhaust opening and
adjacent surrounding area free from the
accumulation of lint, dust, and dirt.
14. The interior of the tumbler and the exhaust duct
should be cleaned periodically by qualified
service personnel.
15. If not installed, operated and maintained in
accordance with the manufacturer’s instructions
or if there is damage to or mishandling of this
product’s components, use of this product could
expose you to substances in the fuel or from fuel
combustion which can cause death or serious
illness and which are known to the State of
California to cause cancer, birth defects or other
reproductive harm.
16. Tumbler will not operate with the loading door
open. DO NOT bypass the door safety switch to
permit the tumbler to operate with the door open.
The tumbler will stop tumbling when the door is
opened. Do not use the dryer if it does not stop
tumbling when the door is opened or starts
tumbling without pressing or turning the START
mechanism. Remove the tumbler from use and
call the service person.
17. Tumbler will not operate with lint panel open.
DO NOT bypass lint panel safety switch to
permit the tumbler to operate with the lint panel
open.
18. Do not put articles soiled with vegetable or
cooking oil in the tumbler, as these oils may not
be removed during washing. Due to the
remaining oil, the fabric may catch on fire by
itself.
19. To reduce the risk of fire, DO NOT put clothes
which have traces of any flammable substances
such as machine oil, flammable chemicals,
thinner, etc. or anything containing wax or
chemicals such as in mops and cleaning cloths, or
anything dry-cleaned at home with dry-cleaning
solvent in the tumbler.
20. Use the tumbler only for its intended purpose,
drying water-washed fabrics.
21. ALWAYS disconnect the electrical power to the
tumbler before servicing. Disconnect power by
shutting off appropriate breaker or fuse.
22. Install this tumbler according to the Installation
Instructions. All connections for electrical
power, grounding, and gas supply must comply
with local codes and be made by licensed
personnel when required.
Hazardous Voltage. Can cause shock, burn
or cause death. Allow machine power to
remain off for two minutes prior to working
in and around AC inverter drive. W359
WARNING

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Safety Information
70381401
8
23. Remove laundry immediately after tumbler stops.
24. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of reach of children at all times
(preferably in a locked cabinet).
25. Do not tumble fiberglass curtains and draperies
unless the label says it can be done. If they are
dried, wipe out the cylinder with a damp cloth to
remove particles of fiberglass.
26. Always follow the fabric care instructions
supplied by the garment manufacturer.
27. Never operate the tumbler with any guards and/or
panels removed.
28. DO NOT operate the tumbler if it is smoking,
grinding or has missing or broken parts.
29. DO NOT bypass any safety devices.
30. Solvent vapors from dry-cleaning machines
create acids when drawn through the heater of the
drying unit. These acids are corrosive to the
tumbler as well as to the laundry load being
dried. Be sure make-up air is free of solvent
vapors.
31. Failure to install, maintain and/or operate this
machine according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
To reduce the risk of serious injury, install
lockable door(s) to prevent public access to
rear of tumblers. W055
WARNING

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 9
70381401
Programming the Electronic OPL Control
Figure 1
Introduction to Programming
Drying can be done automatically or by time dry.
When drying automatically, the tumbler stops drying
when laundry reaches the factory-set or programmed
dryness level and starts Cool Down. When time
drying, the tumbler stops drying when programmed
time ends and starts Cool Down.
Both Automatic Dry and Time Dry have factory-set
cycles, but other cycles can also be created. Frequently
used cycles can be saved in the control's memory as
Custom cycles.
In all cycles except No Heat, Wrinkle-Free begins
when Cool Down ends. During Wrinkle-Free, the
tumbler alternately stops for 2.5 minutes and then runs
without heat for 2.5 minutes until door is opened or 60
minutes has elapsed.
A Custom heat cycle may be saved in one of four ways
using the ON/SELECT pads of HIGH, MEDIUM,
MED LOW and LOW. Refer to Table 1.Table 1
T359I
NOTE: Not all tumblers will have reversing option.
STATUS
DRYING
COOL DOWN
DOOR OPEN
CUSTOM
HIGH
MEDIUM
MED LOW
LOW
NO HEAT
TEMP
DISPLAY
SIGNAL
F/ C
TEMP
PROGRAM
AUTO
SPECIAL
CYCLE
MORE
CONDITION
SPECIAL
TIME
COOL
DOWN
LESS
SAVE
CUSTOM
TIME
*
+--
*
PROG
AUTO
AUTO
ON / SELECT
START
STOP/RESET
REVERSING
One preprogrammed
No Heat cycle
Four preprogrammed
Automatic Dry heat
cycles
All of these cycles
may be used as
preprogrammed
from the factory . . .
They may be
modified for one
cycle without
being saved in
the memory . . .
They may be
modified and
saved in the
memoryasCustom
cycles.
OR OR
Custom Cycles
Automatic Dry Dries the load to one of eleven user-
selectable dryness levels for a given
fabric type, and then enters automatic or
user-variable Cool Down.
Time Dry Duplicates the functions of
electromechanical dual timer controls,
allowing the user to vary temperature,
drying time and Cool Down time.
Special Cycle Allows the user to specify the number
of heating cycles and to select from the
full range of temperatures for all heat
cycles.
Special Time Similar to Time Dry, except that the
user may specify from 80°F (27°C) to
180°F (82°C) for any heat cycle.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming the Electronic OPL Control
70381401
10
Signal
Refer to Figure 3.
The signal has three loudness levels that can be set
anytime the control is activated. Pressing the SIGNAL
pad once produces the softest tone. Press the pad again
to increase signal volume. The fourth press turns the
tone and light off. The loudness level selected is for all
cycles until changed.
When the signal is on and any key pad is pressed, it
sounds at the selected level to confirm the pad was
properly pressed.
Reversing
Refer to Figure 3.
NOTE: Not all tumblers will have the reversing
option.
When this is selected, the cylinder will rotate in one
direction for 25 seconds, pause for six seconds, then
rotate in the opposite direction for 25 seconds.
This sequence will repeat until the selected cycle ends.
To turn reversing option off, press the REVERSING
pad. (Anytime REVERSING pad is pressed, the
cylinder will pause for six seconds.)
Status Lights
Refer to Figure 3.
NOTE: Do not press directly on lights or the center
of pad. For proper selection, press on pad slightly
to the right of center. Refer to Figure 2.
Figure 2
DOOR OPEN
Lights when door is open.
NOTE: Display window also
flashes.
DRYING Lights when laundry is drying.
COOL DOWN Lights when laundry is cooling.
CUSTOM Lights when a Custom cycle is
programmed, recalled or running.
SIGNAL When lit, the signal will sound when
the laundry is ready for removal.
REVERSING
When lit, the cylinder will rotate in
one direction for 25 seconds, pause
for 6 seconds, then rotate in the
opposite direction for 25 seconds.
T398I
Figure 3
STATUS
DRYING
COOL DOWN
DOOR OPEN
CUSTOM
SIGNAL
REVERSING
T398I
STATUS LIGHTS

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming the Electronic OPL Control
11
70381401
Automatic Dry and Condition Mode
When a temperature is selected, “A0:00” will appear
in the display window. Press START to start the
tumbler. “A*:**” will appear in the display window.
The first “*” is the selected dryness level (dryness
levels less than zero will appear as “-*”), and the “:**”
is the elapsed time.
The degree of dryness can be altered. Use the MORE
pad or the LESS pad to increase or decrease dryness
level.
NOTE: Dryness level can only be altered prior to
the end of the first heat cycle.
Figure 4
When clothes reach selected dryness level, Cool Down
begins. “AC:**” will appear in the display window.
“:**” is the elapsed Cool Down time. When Cool
Down ends, tumbler automatically goes into Wrinkle-
Free and “Lr” (Load Ready) will appear in the display.
“AC:**” will be displayed when tumbler is in Auto
Cool Down. Typical Cool Down times for fabric
selections are preset as shown in Table 2. The Cool
Down time can only be altered before cycle is started.
To alter Cool Down time, press the COOL DOWN pad
and then press the MORE or LESS pad (when Cool
Down time is altered, “TC:**” will be displayed). For
one minute changes, press pad and release. For
five minute changes, press pad and hold. Cooling time
can be from 1 to 39 minutes. To return to the Auto
Cool Down, press MORE or LESS pad until “AC:**”
is displayed.
Figure 5
Use the CONDITION pad for items to be left damp for
ironing. “Cn:00” will replace “A0:00” in the display.
Automatic Cool Down ends when either a preset
temperature or a preset time is reached. Refer to Table
2.
Table 2
T399I
HIGH
MEDIUM
MED LOW
LOW
NO HEAT
ON / SELECT
START
STOP/RESET
T399I
ON/SELECT PADS
T396I
Automatic Cool Down
Temperatures and Times
Fabric Preset
Temperature Preset Time
HIGH 100°F, 38°C 5 Min.
MEDIUM 90°F, 32°C 8 Min.
MED LOW 90°F, 32°C 5 Min.
LOW 90°F, 32°C 5 Min.
TEMP
MORE
CONDITION
LESS
+--
T396I
DRYNESS PADS

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming the Electronic OPL Control
70381401
12
Time Dry and No Heat Modes
After temperature selection, press the TIME pad.
Refer to Figure 6.
Figure 6
A preset drying time, “Td:**”, will replace “A0:00” in
the display. This time can be changed by pressing the
MORE or LESS pad. For one minute changes, press
pad and release. For five minute changes, press pad
and hold. Maximum drying time allowed is 60
minutes. Refer to Table 3 for preset drying times.
Table 3
“AC:**” will be displayed when tumbler is in Auto
Cool Down. Typical Cool Down times for fabric
selections are preset as shown in Table 2. The Cool
Down time can only be altered before cycle is started.
To alter Cool Down time, press the COOL DOWN pad
and then press the MORE or LESS pad (when Cool
Down time is altered, “TC:**” will be displayed). For
one minute changes, press pad and release. For
five minute changes, press pad and hold. Cooling time
can be from 1 to 39 minutes. To return to the Auto
Cool Down, press MORE or LESS pad until “AC:**”
is displayed.
To start the cycle, press START. The total drying time
plus Cool Down time will display. During the cycle,
remaining time displays.
No Heat is a Time Dry cycle only. When NO HEAT is
pressed, a 20 minute preset time will display. This can
be changed from 1 minute to 60 minutes by pressing
the MORE or LESS pad before pressing START. The
COOL DOWN pad does not work in No Heat cycles.
T397I
Cycle Preset Time Range
HIGH 35 Min. 1 – 60 Min.
MEDIUM 20 Min. 1 – 60 Min.
MED LOW 15 Min. 1 – 60 Min.
LOW 30 Min. 1 – 60 Min.
NO HEAT 20 Min. 1 – 60 Min.
MORE
COOL
DOWN
LESS
TIME
+--
T397I
TIME DRY PADS

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming the Electronic OPL Control
13
70381401
Custom
Frequently used cycles can be saved in the control’s
memory as Custom cycles. Only one cycle can be
saved for each temperature selection.
Create an Automatic, Time Dry, Special or Special
Time cycle, and save it by pressing the word
CUSTOM before pressing START. To change a
Custom cycle, repeat above.
To recall and use a Custom cycle, press its
ON/SELECT pad twice. Press START.
During Custom cycles, the display is the same as non-
Custom Automatic cycles. The CUSTOM status light
will be on.
When creating or changing a Custom cycle, record it
on a Custom Cycle Record. Refer to sample below. To
modify or fine-tune a Custom cycle, its values must be
known. Custom cycle values can be extracted from the
micro-control, but it is easier and more permanent to
use a Custom Cycle Record.
Custom Cycle Record
Select Automatic Time Temp Load Type
Dryness Level Cool Down Dry Cool Down
HIGH
MED
MED LOW
LOW
NO HEAT
Select Special Special Time Temp Load Type
Dryness Level Cool Down Dry Cool Down
HIGH
MED
MED LOW
LOW
NO HEAT

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming the Electronic OPL Control
70381401
14
Special Cycle Mode
This allows the user to select the number of times the
tumbler will cycle from heat-on to heat-off. To enter
the Special Cycle Mode, press the SPECIAL CYCLE
pad after selecting a cycle. The display will read
“SC:**”. “**” is the number of times the tumbler will
cycle from heat-on to heat-off. This number can be
changed by pressing the MORE or LESS pad. For
increments of one, press pad and release. For
increments of five, press pad and hold for
three seconds. Range is from 1 to 99.
Press the START pad. The number shown after “SC:”
is the number of cycles selected. The number will
decrease as each cycle is completed. The default Cool
Down cycle for the Special Cycle Mode is Automatic
Cool Down.
NOTE: Since there are only 60 minutes of cycle
time, any cycles not completed within 60 minutes
will be skipped.
NOTE: Unlike the Time Dry Mode and Automatic
Mode, the regulating temperature in the Special
Cycle Mode has a range of 80°F (27°C) to 180°F
(82°C) or all heat cycles.
Special Time Mode
This mode is just like the Time Dry Mode, except that
the regulating temperature for each heat cycle ranges
from 80°F (27°C) to 180°F (82°C). To enter the
Special Time Mode, press the SPECIAL TIME pad
after selecting a cycle. The display will read “St:**”,
where “**” is the drying time. This time can be
changed by pressing the MORE or LESS pad. For
one minute changes, press the pad and release. For
five minute changes, press the pad and hold.
Maximum drying time allowed is 60 minutes.
“AC:**” will be displayed when tumbler is in Auto
Cool Down. Typical Cool Down times for fabric
selections are preset. The Cool Down time can only be
altered before cycle is started. To alter Cool Down
time press the COOL DOWN pad and then press the
MORE or LESS pad (when Cool Down time is altered,
“TC:**” will be displayed). For one minute changes,
press pad and release. For five minute changes, press
pad and hold. Cooling time can be from 1 to 39
minutes. To return to the Auto Cool Down, press
MORE or LESS pad until “AC:**” is displayed.
To start the cycle, press START. The total drying time
plus Cool Down time will display. During the cycle,
remaining time displays.
Security Lock-Out
The programming pads can be “locked-out” so
operators cannot change cycles on their own. When
lock-out is used, the operator can use only the factory-
set Automatic cycles and the one Custom cycle
allowed per SELECT pad. Before using lock-out,
create all desired Custom cycles.
To lock-out, hold SIGNAL pad and press MORE in
the idle mode.
To unlock, hold SIGNAL pad and press LESS in the
idle mode.
Show Mode
This mode will show all LEDs and light up entire
display while deactivating all pads. This mode allows
loading door to be opened and closed. To enter this
mode, the control must first be in the idle mode. Hold
the START pad and press the SAVE CUSTOM pad. To
exit Show Mode, hold the START pad and press the
SAVE CUSTOM pad.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Programming the Electronic OPL Control
15
70381401
Temperature Sensor
To test the temperature sensor, hold COOL DOWN
pad and press the TEMP pad in the idle mode. This
will show the temperature detected by the control.
“SH” displays and signal sounds if the temperature
sensor is shorted or sensor temperature is over 200°F
(93°C). Press the STOP/RESET pad twice within
three seconds and allow the tumbler to cool, then press
an ON/SELECT pad. If “SH” still displays, call for
service.
“OP” displays and signal sounds three minutes after
the tumbler is started if the temperature sensor is faulty
or if a temperature below 24°F (-4.4°C) is detected. If
dryer temperature is above 24°F (-4.4°C), call for
service.
NOTE: To display the software revision level, hold
the AUTO pad and press the TIME pad while the
control is in idle mode.
Temperature Adjustment
Selecting a fabric type selects a preset ideal
temperature for that fabric. Lower temperatures may
be needed for small loads or when air flow through the
tumbler is less than ideal due to inadequate make-up
air or exhaust ducting.
Whenever the control is on, but not in No Heat, Cool
Down or Load Ready, pressing the TEMP pad displays
the three digits of the set temperature. Use the MORE
or LESS pad to increase or decrease the temperature.
Temperature Display (°F/°C)
To select between Fahrenheit and Celsius display, hold
in the TEMP DISPLAY pad while pressing the TEMP
pad.
NOTE: Temperature can be set from 80°F (27°C)
to 180°F (82°C) in the SPECIAL CYCLE and
SPECIAL TIME options only.
To include an adjusted temperature in a Custom cycle,
simply adjust temperature before pressing CUSTOM.
Cylinder Temperature Display
To see the approximate temperature at the exit of the
cylinder, press and hold the TEMP DISPLAY pad
(50 to 170 pound models only). For 0220, 0270 and
0350 models, the control program temperature for the
active cycle will be displayed when pressing TEMP
DISPLAY pad.