Allied Telesis AT-FS201 Series User manual

Datasheet | Switches
AT-FS201-xx
2 port Fast Ethernet switch,
10/100TX to 100FX (ST), 2km
AT-FS202-xx
2 port Fast Ethernet switch,
10/100TX to 100FX (SC), 2km
AT-FS232-xx
2 port Fast Ethernet switch media converter
10/100TX to 100FX (SC), 2km
AT-FS232/1-xx
2 port Fast Ethernet switch media converter
10/100TX to 100FX (SC), 15km
AT-FS232/2-xx
2 port Fast Ethernet switch media converter
10/100TX to 100FX (SC), 40km
Extend Networks
The FS200 series switches are the ideal solution
when the time comes to upgrade your
traditional 10Mbps Ethernet network or extend
your 100Mbps Fast Ethernet network. The
FS200 series is designed to extend the distance
of your network by converting Fast Ethernet
data between twisted pair cabling and single-
mode fiber-optic cabling.The FS200 features a
100FX fiber-port and a 10/100TX twisted-pair
port.The fiber-optic port features an SC
connector and an operating distance of 2
kilometers (6,561 feet) to 40 kilometers (24.9
miles) depending on the model. The twisted-pair
port has an RJ-45 connector with a maximum
operating distance of 100 meters (328 feet).
VLAN Support
Many new backbone switch products now
support the industry standard IEEE 802.1Q
specification for irtual LANs ( LANs) that
send extra-long data packets on the
network.The FS200 switches are fully
compatible with these long packets, enabling
them to be used in modern networks. Switches
not supporting this feature will discard these
extra long packets, making them unsuitable for
modern networks.
Small and Flex ble
The small size and external power supply of the
FS200 series allows them to be used almost
anywhere. Additionally, they can be mounted in
a chassis along with Allied Telesis’ media
converters, allowing users to construct any mix
of network conversions when they add the
optional redundant power supply.
M ss ngL nkTM and Smart
M ss ngL nkTM (SML)
The MissingLink feature allows the ports on the
media converter to pass the Link status of their
connections to each other. When the media
converter detects a problem with a port - such
as the loss of connection to a node - it shuts
down the connection to the other port, thereby
notifying the node that the connection has been
lost. The Smart MissingLink (SML) feature
monitors network connections and provides
notification when network segments fails,
allowing network managers to quickly identify
the source and location of failed segments and
minimize downtime.
Key Features
•Convert speed as well as media type
•Auto MDI/MDI-X
•MissingLink (ML) (AT-FS232 only)
•Smart MissingLink (SML) (AT-FS232 only)
•Supports 1532 bytes frame
•Support for multi-mode and single-mode fiber
•Supports half and full-duplex operation
•2k MAC address tables
•Store-and-forward switching mode
•Transparent to IEEE 802.1Q packets
•Standalone or rack-mountable
•ack-mountable using optional AT-MC 12,
AT-T AY4, or AT-T AY1 chassis
•Wall-mountable using AT-WLMT
FS200 Ser es
2 Port Fast Ethernet Speed/Media Converting Switch
Allied Telesis www.alliedtelesis.com

A
T-FS201 and AT-FS202
Status Ind cators
System LEDs
Power Indicates power is applied to the
converter
Per Fiber Port:
Link/Activity Indicates valid/invalid link
Indicated data is being received or
transmitted
Full-duplex/Collision Indicates operation at either full or
half-duplex
Indicates collision during transmission
on the port
Per Copper Port:
Link/Activity Indicates valid/invalid link
Indicates data is being received or
transmitted
Full-duplex/Collision Indicates operation at either full or
half-duplex
Indicates collision during transmission
on the port
Auto-negotiation Indicates port is set for auto-
negotiation
100M Indicates operation at either 10T or
100TX
Operat onal Character s tcs
(Each port can be configured via the following switches)
Per Fiber Port:
Duplex Selects either full- or half-duplex
operation
Bytes Selects maximum packet size sent by
switch (1518 or 1522 bytes)
Per Copper Port:
Auto Selects auto-negotiation mode or
manual setting
Duplex Forces port to full or half-duplex
operation
(Auto setting = manual only)
Speed Forces port to 10 or 100Mbps
operation
(Auto setting = manual only)
Bytes Selects maximum packet size sent by
switch (1518 or 1522 bytes)
MAC address table 2k addresses
Forwarding/Filtering Rate
148,880pps for 100Mbps
14,880pps for 10Mbps
Latency 14.3µsec
(64 byte packet, 100Mbps full-duplex)
Operat onal Mode
MissingLink (ML)
Link Test
AT-FS232, AT-FS232/1 and AT-FS232/2
Status Ind cators
System LEDs:
Power Indicates power is applied to the
converter
Mode status Indicates operating mode, MissingLink,
Smart MissingLink and Link Test
Per Fiber Port:
Link Indicates a valid receive link exists
Duplex Indicates full or half-duplex operation
Collision Indicates collision during packet
transmission on the port
Per Copper Port:
Link Indicates a valid receive link exists
Speed Indicates either 10 or 100Mbps operation
Auto Indicates port is set for auto-negotiation
FD/Collision Indicates collision during packet
transmission on the port
Indicates full or half-duplex operation
Operat onal Character st cs
(Each port can be configured via the following switches)
Per Fiber Port:
Duplex Selects either full or half-duplex
operation
Per Copper Port:
Auto Selects auto-negotiation mode or manual
setting
Duplex Forces port to full or half-duplex
operation
(Auto setting = manual only)
Speed Forces port to 10 or 100Mbps operation
(Auto setting = manual only)
MAC address table 2k addresses
Forwarding/filtering rate
148,880pps for 100Mbps
14,880pps for 10Mbps
Latency 14.3µsec
(64 byte packet,100Mbps full-duplex)
Operat onal Mode
MissingLink (ML)
Smart MissingLink (SML)
Linktest
Power Character st cs
Input voltage (auto-ranging)
External power supply 100-120V AC/60Hz,
220-240V AC/50Hz
Input supply voltage 12vDC +/- 5%
Max current .5
Power consumption 6W
Env ronmental Spec f cat ons
Operating temp. 0°C to 40°C
Storage temp. -20°C to 80°C
Relative humidity 5% to 95% non-condensing
Operating altitude 0 to 10,000 feet
Phys cal Character st cs
Dimensions 10.5cm x 9.5cm x 2.5cm
(4.12" x 3.75" x 1.0")
Weight 0.7lb
Electr cal/Mechan cal Approvals
EMC FCC Class A
Safety UL-Cul, CSA/CSA, RTL, TUV,
CE compliant
FS200 Ser es | 2 Port Fast Ethernet Speed/Media Converting Switch
USA Headquarters |19800 North Creek Parkway |Suite 100 |Bothell |WA 98011 |USA |T: [phone] |F: [phone]
European Headquarters |Via Motta 24 |6830 Chiasso |Switzerland |T: +41 91 69769.00 |F: +41 91 69769.11
Asia-Pacific Headquarters |11 Tai Seng Link |Singapore |534182 |T: [phone] |F: [phone]
www.alliedtelesis.com
© 2011 Allied Telesis Inc. All rights reserved. Information in this document is subject to change without notice. All company names, logos, and product designs that are trademarks or registered trademarks are the property of their respective owners. 617-00342 Rev K
Order ng Informat on
AT-FS201-xx
2 port Fast Ethernet switch,
10/100TX to 100FX (ST), 2km
AT-FS202-xx
2 port Fast Ethernet switch,
10/100TX to 100FX (SC)
AT-FS232/y-xx
2 port Fast Ethernet switch media converter
10/100TX to 100FX (SC)
Where y = Multi-mode fiber 2km
1 single-mode fiber 15km
2 single-mode fiber 40km
Where xx =10 AC power supply, US power cord
20 AC power supply, European power cord
30 AC power supply, UK power cord
40 AC power supply, Australian power cord
Assoc ated Products
AT-MC 12 12 slot AC or DC powered chassis
AT-T AY4 Mounting tray for up to four devices
AT-T AY1 Mounting tray for one device
AT-WLMT Wall-mount for one device