Allied Telesis TurboStack AT-TSA2 User manual

1
TurboStack
TM
AT-TSA x
Appliqués
AT-TSA1
AT-TSA2
AT-TSA3
AT-TSA5
AT-TSA8
AT-TSA9
User Manual

User Manual
2
 Copyright 1996 Allied Telesyn International Corp.
All rights reserved. No part of this publication may be reproduced without prior
written permission from Allied Telesyn International.
Allied Telesyn International reserves the right to make changes in specifications
and other information contained in this document without prior written notice.
The information provided herein is subject to change without notice. In no event
shall Allied Telesyn International be liable for any incidental, special, indirect, or
consequential damages whatsoever, including but not limited to lost profits,
arising out of or related to this manual or the information contained herein, even if
Allied Telesyn International has been advised of, known, or should have known,
the possibility of such damages.

i
Electrical Safety and Installation Requirements
RADIATED ENERGY
U.S. Federal Communications
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and , if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC,
can void your right to operate this equipment.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
STANDARDS: This product meets the following standards
RFI EmissionEN55022 Class A
WARNING: In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Immunity EN50082-1
Electrical Safety EN60950, UL1950, CSA 950
SAFETY
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHT-
NING ACTIVITY.
This is a “CLASS 1 LED PRODUCT”
OPERATING TEMPERATURE: This product is designed for a maximum ambient
temperature of 40 degrees C.
ENVIRONMENTAL AIR NOTICE
Caution: UL listed for use in other Environmental Air Spaces in Accordance with Article
300-22(C) of the U.S.A National Electrical Code.
Note: Product is not Plenum rated
ALL COUNTRIES: Install product in accordance with local and National Electrical
Codes.
NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Hochfrequenzstörung EN55022 Klasse A
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen
hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.
Störsicherheit EN50082-1
Elektrische Sicherheit EN60950, UL1950, CSA 950

ii
SICHERHEIT
GEFAHR DURCH BLITZSCHLAG
GEFAHR:
Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen
Das ist ein “LED Produkt der Klasse 1”
BETRIEBSTEMPERATUR
Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als
40 ° C entworfen.
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften
entsprechen.
Radiofrekvens forstyrrelsesemission EN55022 Klasse A
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver
det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger.
Immunitet EN50082-1
Elektrisk sikkerhed. EN60950, UL1950, CSA 950.
SIKKERHED
FARE UNDER UVEJR
FARE:
UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.
Dette er et “PRODUKT UNDER KLASSE 1 LED”
BETJENINGSTEMPERATUR
Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C.
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og
national lovgivning for elektriske installationer.
RFI Emissie EN55022 Klasse A
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk
geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.
Immuniteit EN50082-1
Electrische Veiligheid EN60950, UL1950, CSA 950
VEILIGHEID
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR:
NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
Dit is een “KLASSE 1 LED-PRODUKT”
BEDRIJFSTEMPERATUUR
De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden
Celsius.
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.

iii
NORMES: ce produit est conforme aux normes de suivantes :
Emission d’interférences radioélectriques EN55022 Classe A
MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des
interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures
adéquates.
Immunité EN50082 - 1
Sécurité électrique EN60950, UL1950, CSA 950
SÉCURITÉ
DANGER DE FOUDRE
DANGER:
NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.
Ce matériel est un “PRODUIT À DIODE ÉLECTROLUMINESCENTE DE CLASSE 1”
TEMPÉRATURE DE FONCTIONNEMENT
Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques
nationales et locales.
Radioaaltojen häirintä EN55022 Luokka A
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin.
Kestävyys EN50082-1
Sähköturvallisuus EN60950, UL1950, CSA 950
TURVALLISUUS
ALAMANISKUVAARA
HENGENVAARA:
ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE”
KÄYTTÖLÄMPÖTILA
Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40 ° C.
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten
mukaisesti.
Emissione RFI (interferenza di radiofrequenza) EN55022 Classe A
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio
interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati
provvedimenti.
Immunità EN50082-1
Sicurezza elettrica EN60950, UL1950, CSA 950

iv
NORME DI SICUREZZA
PERICOLO DI FULMINI
PERICOLO:
NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.
Questo è un “PRODOTTO CON LED DI CLASSE 1”
TEMPERATURA DI FUNZIONAMENTO
Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche
nazionali.
RFI stråling EN55022 Klasse A
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
Immunitet EN50082-1
Elektrisk sikkerhet EN60950, UL1950, CSA 950
SIKKERHET
FARE FOR LYNNEDSLAG
FARE:
ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
Dette er et “KLASSE 1 LED PRODUKT”
DRIFTSTEMPERATUR
Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius.
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske
koder.
Emissão de interferência de radiofrequência EN55022 Classe A
AVISO: Num ambiente doméstico este produto pode causar interferência na
radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas.
Imunidade EN50082-1
Segurança Eléctrica EN60950, UL1950, CSA 950
SEGURANÇA
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO:
NÃO TRABALHE no equipamento ou nos CABOS durante períodos suscetíveis
a QUEDAS DE RAIO.
Este é um “PRODUTO CLASSE 1 LED”
TEMPERATURA DE FUNCIONAMENTO
Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais para
instalações elétricas.

v
Emisión RFI EN55022 Clase A
ADVERTENCIA: en un entorno doméstico, este producto puede causar
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que
sean convenientes al respecto.
Inmunidad EN50082-1
Seguridad eléctrica EN60950, UL1950, CSA 950
SEGURIDAD
PELIGRO DE RAYOS
PELIGRO:
NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos
o en LOS CABLES durante TORMENTAS ELECTRICAS.
Este es un “PRODUCTO DE DIODO LUMINISCENTE (LED) CLASE 1”
TEMPERATURA REQUERIDA PARA LA OPERACIÓN
Este producto está diseñado para una temperatura ambiental máxima de 40 grados C.
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos Eléctricos
locales y nacionales.
Radiostörning EN55022 Klass A
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan
tvinga användaren till att vidtaga erforderliga åtgärder.
Immunitet EN50082-1
Elsäkerhet EN60950, UL1950, CSA 950
SÄKERHET
FARA FÖR BLIXTNEDSLAG
FARA:
ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
Detta är en “KLASS 1 LYSDIODPRODUKT”
DRIFTSTEMPERATUR
Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader Celsius.
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser
för elektrisk utrustning.

vii
Table of Contents
Electrical Safety and Installation Requirements . . . . . . . . . . . . i
TurboStack™ Hub Appliqués . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
TurboStack Hub Connection Options . . . . . . . . . . . . . . . . . . . . . . 1
External Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Network Appliqués. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Location of Appliqué Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Network Appliqué Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Appliqué Installation/Removal Procedures. . . . . . . . . . . . . . . . . . 4
Technical Support Fax Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Incident Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AT-TSAx Manual Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Where To Find Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
List of Figures
Figure 1: AUI Network Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2: AT-TS06/SC Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 3: AT-TSAx Appliqués . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 4: Appliqué Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
List of Tables
Table 1: ATI Micro Transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table 2: Appliqué List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1
TurboStack™ Hub Appliqués
This manual describes the hub appliqué options and installation procedures for
ATI’s TurboStack™ hubs. For information on the software installation and
network management aspects of TurboStack hubs, see the separate TurboStack
Manageable Hub Installation Manual and TurboStack AT-S10 Operations
Manual . These publications are shipped with each manageable hub.
TurboStack Hub Connection Options
In a TurboStack department concentrator chassis, manageable hubs can be
connected to network zones using different cable media by installing different
appliqués or external transceivers.
Note
This manual refers to two or more chassis-mounted hubs, at least one of which is
manageable, as a department concentrator. The term hub refers to either a
standalone hubs (i.e., a single manageable device) or a department concentrator
configuration.
External Transceivers
The appliqué port on all TurboStack hubs with management are pre-configured
with the AUI appliqué. You can configure the AUI network port to another media
type by using an external transceiver. Table 1 shows the ATI micro transceivers
available for this purpose.
Table 1: ATI Micro Transceivers
Model Description
AT-MX40F/ST Fiber Optic (10BASE-FL), ST Connector
AT-MX50F/SM Fiber Optic (10BASE-FL), SMA Connector
AT-MX55F/SC Fiber Optic (10BASE-FL), SC Connector
AT-210T/210TS/MX20T UTP (10BASE-T), RJ45 Connector
AT-MX10/MX10S Thin Ethernet (10BASE2), BNC Connector

2
If you use an external transceiver for a backbone connection, the transceiver
should be connected to an AUI appliqué on the hub faceplate. Figure 1 shows the
factory-installed AUI connector and plastic cover provided with all TurboStack
hubs.
Figure 1: AUI Network Connector
Network Appliqués
If the network backbone is 10BASE2, 10BASE-T or fiber optic (10BASE-FL), an
appliqué can be used instead of an external transceiver. Table 2 lists the available
TurboStack appliqué options.
Table 2: Appliqué List
Model Connector Type Description
AT-TSA1 SMA 10BASE-FL
AT-TSA2 SC 10BASE-FL
AT-TSA3 ST 10BASE-FL
AT-TSA5 AUI 10BASE5
AT-TSA8 BNC 10BASE2
AT-TSA9 RJ45 10BASE-T