Allnet ALL0488V6 User manual

ALL0488V6
PoE-Injector
User Manual

© ALLNET GmbH Computersysteme 2022 – All rights reserved
Errors and changes reserved
2
1. Overview
1.1 Product Description
The ALL0488V6 is fully compliant with IEEE802.3at standard. It delivers
up to 30W output power. By using this device, both data and electrical
power can be simultaneously delivered through a single CAT.5 (or better)
ethernet cable.
1.2 Features
-complies with IEEE802.3, IEEE802.3u, IEEE802.3ab and IEEE802.3at
-2* RJ‐45 Ports 10/100/1000 Mbits
-Plug&Play Installation
-delivers both data and electrical power using a single ethernet cable
-Green‐IT, low power consumption
-over‐voltage/current/load protection
-compact size
-delivers data up to 100 meters
1.3 Package Content
-1x ALL0488V6
-1x IEC-C5 Power cord
-1x User Manual
1.4 Environmental Requirement
-To avoid potential short circuit or malfunction, do not expose the
adapter to heat, humidity, vibration or dust.
-Keep the device at least 30 cm away from heat sources.
-Make sure the cable connected to the PoE‐Device does not exceed 100
meters in length for better performance. (total cable length, Uplink to
Injector + Injector to Device)

© ALLNET GmbH Computersysteme 2022 – All rights reserved
Errors and changes reserved
3
1.5 The device
A
POWER LED
lights up green as soon as the ALL0488V6
is supplied with power
B
ACTIVE
Lights up green as soon as the ALL0488v6 supplies
an end device with PoE
C
DATA IN
Connect this port to your network
or PC
D
PoE
Connect your PoE end devices to be supplied
to this port
E
Mounting
Via these two eyelets you can mount the
ALL0488v6 mount on a wall/plate
F
Power connection
Connect the supplied IEC 320-C5 (Mickey) cable
here

© ALLNET GmbH Computersysteme 2022 – All rights reserved
Errors and changes reserved
4
2. Installation
Use the supplied power cable to connect the ALL0488v6 to a power outlet.
Connect the "LAN IN" port of the ALL0488v6 to the network/switch.
Connect the PoE device to the "PoE" port.

© ALLNET GmbH Computersysteme 2022 – All rights reserved
Errors and changes reserved
5
3.Technical specifications
Element
Specifikation
Standards:
•
IEEE802.3 10Base-T Ethernet
•IEEE802.3u 100Base-Tx Fast Ethernet
•IEEE802.3ab 1000Base-T Gigabit Ethernet
•Support terminal equipment with IEEE802.3af/at, PoE++
•RoHS Compliance
•WEEE Compliance
Ethernet
Ports:
•
1x RJ45 10/100/1000 Mbps for connection to switch or hub
•1x RJ45 10/100/1000 for connection to PoE end device
PoE Output:
PoE IEEE802.11af/at, Power pins: 4/5(+) 7/8(
-)
Power
supply:
100 - 240VAC, internal power supply / Output: 55V/550mA incl. connection
cable
earth contact on IEC320-C5 "Kleeblat/Micky-Mouse" approx. 80cm
length
Power
consumption:
30 Watt maximum with connected PoE end device
AC Surge
Protection:
•
1.0KV (5P/5N)
•L-N 1.2/50 (8/20) Tr/Th us
•2.0KV (5P/5N)
•L-PE 1.2/50 (8/20) Tr/Th us
•N -PE
Housing:
Plastic housing
Mounting:
Wall-mounted
Dimensions:
length/width/height: 140 x 63 x 33 mm
Environment:
Operating Temperature: 0 ~ 40 °C
Operating Humidity 10% ~ 90% (non
-condensing)
Storage Temperature:
-20 ~ 90 °C
Storage Humidity: 10% ~ 90% (non-condensing)
EMI:
•
FCC CFR47 Part 15
•EN55024
•EN55032
EMS:
•
IEC61000-4-2(ESD) ± 6kV(contact), ±8kV(air)
•IEC61000-4-3(RS) 10V/m(80MHz~2GHz)
•IEC61000-4-4(EFT) Power Port: ±2kV; Data Port:±1kV
•IEC61000-4-5(Surge) Power Port:±1kV/DM, ±2kV/CM
•IEC61000-4-6(CS) 10V(150kHz~80MHz)
Immunity:
•
IEC60068-2-6(Vibration)
•IEC60068-2-27(Impact)
•IEC60068-2-32(Free Fall)
Marks:
CE; FCC

© ALLNET GmbH Computersysteme 2022 – All rights reserved
Errors and changes reserved
6
ALLNET GmbH Computersysteme declares that the device ALL0488v6 is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/30/EU. The Declaration of conformity can be found under this
link: http://ce.allnet.de
ALLNET GmbH Computersysteme
Maistrasse 2
82110 Germering
Tel.: [phone] - 22
Fax: [phone] - 33
Email: [email protected]
This recycle logo Indicates that this product is capable of being recycled, not that the
product has been recycled or will be accepted in all recycling collection systems.
The RoHS directive aims to restrict certain dangerous substances commonly used in electronic and
electronic equipment. This RoHS compliant symbol indicate the component is tested for the presence
of Lead (Pb), Cadmium (Cd), Mercury (Hg), Hexavalent chromium (Hex-Cr), Polybrominated biphenyls
(PBB), and Polybrominated diphenyl ethers (PBDE). For Cadmium and Hexavalent chromium, there
must be less than 0.01% of the substance by weight at raw homogeneous materials level. For Lead,
PBB, and PBDE, there must be no more than 0.1% of the material, when calculated by weight at raw
homogeneous materials. Any RoHS compliant component must have 100 ppm or less of mercury and
the mercury must not have been intentionally added to the component.

© ALLNET GmbH Computersysteme 2022 – All rights reserved
Errors and changes reserved
7
Safety Warnings
For your safety, be sure to read and follow all warning notices and instructions.
Do not open the device. Opening or removing the device cover can expose you to
dangerous high voltage points or other risks. Only qualified service personnel can
service the device. Please contact your vendor for further information.
Do not use your device during a thunderstorm. There may be a risk of electric shock
brought about by lightning.
Do not expose your device to dust or corrosive liquids.
Do not use this product near water sources.
Make sure to connect the cables to the correct ports.
Do not obstruct the ventilation slots on the device.