AllSportSystems DIY Bay User manual

1
DIY Bay™ Installation Guide
2/27/2023

USE THIS PRODUCT AT YOUR OWN RISK. NO CLAIM IS MADE AS TO ITS
SAFETY, FITNESS, OR RELIABILITY FOR ANY PURPOSE. HITTING GOLF
BALLS IN AN INDOOR ENVIRONMENT IS EXTREMELY DANGEROUS!
ALWAYS EXERCISE CAUTION WHEN USING YOUR SYSTEM. WE
RECOMMEND HITTING 'ALMOST GOLF' BALLS OR SIMILAR
LIGHTWEIGHT GOLF BALLS FOR INCREASED SAFETY. NEVER SWING A
GOLF CLUB IN CLOSE PROXIMITY TO PETS OR PEOPLE. ALWAYS
STAND AS CLOSE AS POSSIBLE TO THE HITTING BAY TO MINIMIZE THE
RISK OF STRAY SHOTS FLYING OUTSIDE THE ENCLOSURE. NEVER
ALLOW ANYONE TO STAND IN FRONT OF YOU, OR ON EITHER SIDE OF
THE ENCLOSURE WHILE YOU ARE HITTING!
IMPORTANT WARNING
2

Connector Kit:
●6 x 3-Way Connectors
●2 x 90° Connector
●3 x Couplers (only if wider than 10ft)
EMT Pole Kit (optional upgrade):
●8 x Height EMT Poles + 4 x couplers
●6 x Width EMT Poles + 3 x couplers
●4 x Depth EMT Poles
DIY Bay Parts List
Fabric Parts:
●1 x Black Fabric Wrapper
●2 x Black Pole Sleeves
●1 x Impact Screen
●4 x Screen/Foam Trim Panels
●8 x Foam Inserts (optional)
Additional Hardware:
●2 x hex bolts are provided
for each coupler.
●Ball Bungee Straps
3

●Replace eye-bolts with hex bolts
on all couplers.
●Do not insert pole all the way into
couplers. Pull pole about ¼” back
from the crimp point.
Forcing poles all the way to
crimp may cause poles to
exit coupler at an angle.
4
Couplers & Corner Connectors
Insert poles ¼” from crimp
For couplers only, replace
eye-bolts with hex bolts
●Mark and insert poles 4-½” into
3-Ways and 90° Connectors.
!

Bay Size 10’ Poles
Needed Height Width Width Extension Depth
8’H x 10’W x 5’D 9QTY 4 Poles
7’-9”
QTY 3 Poles
9’-9” None needed QTY 2 Poles to 4 pieces 4’-9”
9’H x 10’W x 5’D 9QTY 4 Poles
8’-9”
QTY 3 Poles
9’-9” None needed QTY 2 Poles to 4 pieces 4’-9”
9’H x 12’W x 5’D 10 QTY 4 Poles
8’-9”
QTY 3 Poles 10’
(no cuts)
QTY 1 pole to
3 pieces 1’9”
QTY 2 Poles to 4
pieces 4’-9”
9’H x 14’W x 5’D 11 QTY 4 Poles
8’-9”
QTY 3 Poles 10’
(no cuts)
QTY 2 poles to
3 pieces 3’9”
QTY 2 Poles to 4
pieces 4’-9”
9’H x 16’W x 5’D 12 QTY 4 Poles
8’-9”
QTY 3 Poles 10’
(no cuts)
QTY 3 poles to
3 pieces 5’9”
QTY 2 Poles to 4
pieces 4’-9”
DIY Bay 1” EMT Pole Cutting Chart (5ft Deep)
5
See SkyRailPlus setup guide for modified cage assembly if this upgrade is included. Note
that your EMT pole count will be reduced by 2 width poles for this upgrade.
!
Actual dia 1-3/16”
(30.16 mm)
●1” Common EMT 10-ft conduit can be purchased from a local home improvement store. Use the
chart below to purchase correct quantity and cut to the proper lengths.
Use this chart to purchase and cut your own EMT Poles for cages 5ft Deep
Tip: If you ordered custom bay, all poles are cut 3” shorter than desired cage dimension.

1) BUILD
BOTTOM
2x 3-Ways
2x 90°
2x Depth poles
1x Width pole
1x Coupler + extender*
2) BUILD
REAR
2x 3-Ways
2x Height poles
1x Width pole
1x Coupler + extender*
3) BUILD
DEPTH 2x Depth poles
4) BUILD
FRONT
2x 3-Ways
2x Height poles
1x Width pole
1x Coupler + extender*
6
Cage assembly for EMT’s Purchased Locally
* Couplers + extender poles only needed
for bays larger than 10ft wide.
Use this diagram to assemble your cage from EMT’s purchased and cut locally
●On each coupler replace eye-bolts with hex bolts.
●Insert poles ¼” from the crimp in couplers.
●Insert poles 4½” into 3-Ways and 90° connectors.
See SkyRailPlus setup guide for modified cage assembly if this upgrade is included. Note
that your EMT pole count will be reduced by 2 width poles for this upgrade.
!

Bay Size Height Poles Width Poles Depth Poles
8’H x 10’W x 5’D QTY 8 Poles
3’-11 ½”
QTY 6 Poles
4’-10 ½”
QTY 4 Poles
4’-9”
9’H x 10’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
4’-10 ½”
QTY 4 Poles
4’-9”
9’H x 12’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
5’-10 ½”
QTY 4 Poles
4’-9”
9’H x 14’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
6’-10 ½”
QTY 4 Poles
4’-9”
9’H x 16’W x 5’D QTY 8 Poles
4’-4 ½”
QTY 6 Poles
7’-10 ½”
QTY 4 Poles
4’-9”
DIY Bay 1” EMT Pole Kit Chart (5ft Deep)
7
If custom bay, assembled pole lengths will be 3” shorter than desired cage dimension.
This chart shows quantity and length of poles for the Precut 1” EMT Pole Kit upgrade, for 5ft deep cages
See SkyRailPlus setup guide for modified cage assembly if this upgrade is included. Note
that your EMT pole count will be reduced by 2 width poles for this upgrade.
!

1) BUILD
BOTTOM
2x 3-Ways
2x 90°
2x Depth poles
2x Width pole + coupler
2) BUILD
REAR
2x 3-Ways
4x Height poles + couplers
2x Width poles + coupler
3) BUILD
DEPTH 2x Depth poles
4) BUILD
FRONT
2x 3-Ways
4x Height poles + couplers
2x Width poles + couplers
●On each coupler replace eye-bolts with hex bolts.
●Insert poles ¼” from the crimp in couplers.
●Insert poles 4½” into 3-Ways and 90° connectors.
8
Cage assembly for EMT Pole Kit
Use this diagram to assemble your cage using the EMT Pole kit
See SkyRailPlus setup guide for modified cage assembly if this upgrade is included. Note
that your EMT pole count will be reduced by 2 width poles for this upgrade.
!

Confirm Cage Size
IMPORTANT: BEFORE PROCEEDING
Verify that the outer dimensions match the
expected size. If not, adjust depth that poles
are inserted to connectors as needed.
Height
9
Width
Depth

●2x Blackout Velcro sleeves
(top depth poles only)
10
Add Blackout Sleeves

●Drape wrapper over the
cage with grommets at the
back.
●Wrap sides under bottom
depth poles connecting to
velcro.
●Wrap front edge around
front height and width
poles last connecting to
velcro.
11
Install the Wrapper

●Bungee wrapper to rear
poles.
Bungee balls face toward inside
of the cage.
Rear of cage
12
Wrapper continued…

13
Install Screen
AllSportSystems logo bottom left screen corner
●Screen Orientation:
AllSportSystems Logo should
face to the front.
Velcro is sewn along all edges
on screen front.
●Starting at the corners,
bungee the screen to top and
bottom poles.
●Bungee to side poles last.
Bungee balls for screen installation should face
outside of the cage.
Front View
of cage
Screen front

14
Install Baffle net (optional)
●If you purchased baffle net, use
cable ties to attach the net to
the rear of of the cage.

●Close Flaps on wrapper and
bungee to rear poles.
Rear of cage
15
Close Flaps

1. Attach long edge of trim
fabric to side wall velcro.
2. Position optional foam
wedges as shown. Wrap
trim fabric around foam
and attach to screen
velcro.
Repeat for other side and top.
Bungee balls may need to be adjusted when attaching fabric trim to
main wrapper.
12
16
Install Side & Top Trim Fabric

1. Attach trim fabric to
bottom pole using ball
bungees
2. Place optional foam
wedges on trim fabric.
3. Wrap fabric around
foam and velcro to
bottom of screen.
1
3
2
17
Install Bottom Trim Fabric

Finished Trim
Trim panels will overlap each other.
18

19
Your DIY Bay™ is ready to go!
●If you purchased SkyGuard™ or Triangle netting upgrades see respective Setup Guide.