ALPHA-STIM M User manual

56 7 8
Timer
Change Intensity
(Channel 1)
Frequency
12
3
Probes should be
placed on opposite
sides of the body, so the
current goes through the
area of pain
Repeat treatment as
necessary, varying
probe positions but
always directing the
current between the
probes through the area
being treated
Continue treatment until
pain is completely gone
or maximum relief is
achieved
QUICK START GUIDE
ALPHA-STIM M: SMART PROBES
PLACEMENT TIPS
2. Set frequency to 0.5 HZ
5. First treat in a large "x" pattern,
beyond the treatment area (e.g.,
the entire leg for knee pain, the
entire back for back pain)
1. Power on device
3. Set timer to the 10 second
probe setting
4. Set intensity on the channel
in use
6. Treat in a small star pattern by
applying the probes close in, around
and through the area being treated,
at about 6 different angles of approach
7. Treat the same body part on the
opposite side of the body in at least
2 places (e.g. "x" pattern)
8. Connect the two sides of the body
Follow every treatment
with CES using Alpha-
Stim earclips
When done, remove and
discard earclip pads
Clean earclips with
alcohol, let dry, and
replace 4 earclip pads for
the next treatment
AFTER TREATMENT
®
Power Button
Lock
[
[
Intensity Level
(Channel 1)
Change Intensity
(Channel 2)
Intensity Level
(Channel 2)
For how-to videos, visit www.alpha-stim.com/training
For free clinical support, call 1-800-367-7246
4
IFU-QG-001

Timer
Change Intensity
(Channel 1)
Frequency
12
3
6. You can use two pairs of AS-Trodes
in an X shape (crisscross pattern) with
each line belonging to a pair of
AS-Trodes
7. Repeat as necessary, varying
AS-Trode positions but always
directing the current between them
and through the area being treated
Use level 6 for maximum
pain relief
Decrease immediately if
uncomfortable
Use level 1 when using
AS-Trodes for over 1 hour
CHOOSE THE
INTENSITY LEVEL
RIGHT FOR YOU
Power Button
QUICK START GUIDE
ALPHA-STIM M: AS-TRODES
IMPORTANT NOTES
2. Set frequency to 0.5 HZ
dry skin, placing them to direct the
current between them and
through the area of pain
1. Power on device
3. Set timer for 20 minutes to
1 hour per AS-Trode location
4. Set intensity on the channel or
channels in use
5. Place AS-Trodes on clean,
Follow every treatment
with CES using
Alpha-Stim earclips
Place AS-Trodes on
plastic backing and return
to zippered bag for storing
AFTER TREATMENT
For how-to videos, visit www.alpha-stim.com/training
For free clinical support, call 1-800-367-7246
Lock
Use only AS-Trode brand
electrodes
Many electrodes are
significantly less conductive
and will not allow the
Alpha-Stim® current to
penetrate the electrical
resistance of the skin
Discard and replace
AS-Trodes when adhesive
has split or worn through to
the conductive backing
56
TM
®
[
[
Intensity Level
(Channel 1)
Change Intensity
(Channel 2)
Intensity Level
(Channel 2)
IFU-QG-001
4

Timer
Change Intensity
(Channel 1)
Frequency
1
3
5
QUICK START GUIDE
ALPHA-STIM M: EARCLIPS
®
Power Button
Lock
[
[
Intensity Level
(Channel 1)
Change Intensity
(Channel 2)
Intensity Level
(Channel 2)
For how-to videos, visit www.alpha-stim.com/training
For free clinical support, call 1-800-367-7246
When the timed session
ends, and a “heavy”
feeling is still experienced,
resume treatment until
heaviness lifts and a light
feeling develops
ALWAYS COMPLETE
YOUR TREATMENT
Clean ear lobes with mild
soap and water, alcohol
pads or antibacterial wipes
and allow skin to dry
BEFORE YOU START
Saturate new Earclip
Electrode Pads (EEPs™)
thoroughly with several
drops of conducting solution
Remove and discard
earclip pads
Clean earclips with
alcohol, let dry, and
replace 4 earclip pads for
the next treatment
AFTER TREATMENT
2. Set frequency to 0.5 HZ
1. Power on device
3. Set timer to 20 minutes if the
current is at 2.5 or higher or 1
hour if the current is at 2 or lower
4. Apply one Earclip to each
earlobe (pre-wet with conducting
solution)
5. Increase current until a slight
dizzy feeling is experienced, then
decrease immediately until the
dizziness stops
4
2
IFU-QG-001