Alphamount APCH01B User manual

Kid Bicycle Helmets Instruction Manual
V1.0
Model: APCH01B/APCH01A
Thank you for choosing this Alphamount product! At Alphamount we strive to
provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact at
[email protected] (US/CA)
5. (Refer to Fig. D)After adjusting the strap to proper length, put the
helmet on your head. The helmet must sit firmly and level on your head.
To lower the front of the helmet to cover your forehead, tighten the
front chin strap and loosen the rear strap. To raise the front, loosen the
front chin strap and tighten the rear strap.
To check for proper tension, put on the helmet and fasten the buckle.
Open your mouth. You should feel the strap pulling against your chin.
Then attempt to pull the helmet off the front or rear. If the helmet
comes off, increase strap tension and examine if thick enough pads are
being used. The helmet should not be able to roll forward or backward
excessively. It should not be possible to remove the helmet without
unfastening the buckle.
6. Final Check
6-1.The important thing to remember is that the helmet should be fitted
snugly. If you can tilt it forward or backward you need to tighten the
strap.The straps should be positioned that they do not cover the ears or
eyes and that the buckle is away from the jaw when correctly fitted.
6-2. It is important to make sure the helmet to fit snugly on your head
and must be fastened to provide maximum protection.
6-3. All adjustments should be checked each time the helmet is worn,
making sure it fits snugly at all times.
Fig. C
Fig. D
Level

Step 1
Step 3
12
• Please use the helmet under the parent's supervision
•Please carefully read all instructions before attempting installation. If
you do not understand the instructions or have any concerns or ques-
tions, please contact our customer service at [email protected].
• CAUTION: Avoid potential personal injuries and property damage!
• This helmet is designed to absorb the energy of a blow by partial
destruction or damage itself. Even though such damage may not be
visible, the helmet should be destroyed or replaced, if it is involved in an
injury- related fall.
• Unfortunately, some accidents result in head injury that cannot be
prevented by ANY helmet. Depending on the type of impact, even very
low speeds can result in a serious head injury or fatality. Always ride
with extreme caution and be sure to read this manual thoroughly.
• The helmet is designed and intended exclusively for use while cycling,
and other non-motorized sports. It is not intended for and will not
provide adequate, safe protection if used during motor sport or moped
use. No helmet can protect the wearer against all unforeseeable
impacts. However, for maximum protection, the helmet must be fitted
well and all retention straps must be securely fastened.
• Please keep helmet out of extreme heat. Helmets will be damaged if
exposed to temperatures exceeding 150° F. Dark vehicles and storage
bags can exceed this on very hot days. Heat damaged helmets will have
random disfigured areas where the texture appears bubbly and uneven.
If damaged, helmets should be destroyed and replaced immediately.
• Clean the helmet with mild soap and water only.The use of any
solvents, paints or decals can cause damage to the helmet and make it
ineffective in the result of an accident.
• The helmet is applicable to the people with head circumference in a
range of 18.11-20.47in.(46-52cm)
Important Safety Information
Installation steps
1. To proper wear the helmet, put the helmet on your head first.
3. (Refer to Fig. B)If the strap is too loose or tight, you can take off the
helmet to adjust the straps to proper length.
Situation A: If the front chin strap is too loosen, hold the buckle [a] with
one hand. Then pull the excess chin strap in through.
Situation B: If the rear strap is too loose, hold the buckle with one hand.
Then pull the excess rear strap in through.
2. (Refer to Fig. A)Then adjust the tension around the head by rotating
the dial fit.
Front Chin Strap
Fig. A
Fig. B
Turn clockwise to
narrow the head
circumference
4. (Refer to Fig. C)Hold the helmet with one hand, and hold the strap
where they pass under your chin with the other hand. Then pull the strap
from side to side to balance the length of all four straps.
Turn count-
er-clockwise
to enlarge the
head circumfer-
ence
Adjustable Range of the Dial
Fit: 18.11-20.47in.(46-52cm)
Rear Strap
Buckle [a]