Alpine GXT618S User manual

GXT618S
Modern LED Fire Fountain
with Lights and Vertical
Brick Detail
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed
from the highest quality materials. In the event that we have not achieved our usual standard of
excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of
purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper
storage that allows water to freeze within a product may cause damage and is considered
negligence and will, therefore not be covered under this warranty. The use of “hard water”
and/or caustic cleaners can affect the paint or other finishes. Failure to keep the unit clean,
and use of such additives/cleaners, will also void the warranty. Please note: for fountains,
it is normal for some splashing to occur and protecting the immediate surfaces is not the
responsibility of Alpine Corporation
Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed to protect the entire finish against breakdown
of color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading within the first year from date of
purchase with the above exclusion.
Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that is not an option, you can contact Alpine Corporation at
www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to
show proof of purchase, provide photographs and any other information needed to
validate your claim. This may be necessary to distinguish between a partial or complete
replacement of a defective product. The warranty does not cover any items with multiple
parts; the warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department.
Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim

3
Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging. Some splashing may occur.
Components:
Fountain
Back Cover
Pump
Transformer
LED Light Strand
Fire Box
Assembling:
Place the fountain on a smooth and level surface.
Place the plastic fire wood in the front of the fire box (Figure 1)
Place the fire box inside the fountain with the on/off switch facing the
back and tighten with nuts provided. (Figure 2)
Remove the back cover from the fountain. Pull out the LED light strand
and make sure that the LED strand and the fire box strand are
connected to the splitter. Connect splitter to the transformer. (Figure 2)
Connect the vinyl tubing to the water pump from inside the fountain.
Adjust the flow control on the pump to the lowest setting to avoid
splashing until the fountain is completely assembled. Place the pump
back into the reservoir. Place the back cover back on the fountain.
(Figure 2)
Gently pour water into the fountain, being careful not to overflow and
cause splashing. Make sure the water completely submerges the pump
and the water flows smoothly during operation. (Figure 3)
Plug the pump cable and the transformer into your local power supply.
Make sure that there is no water around the plug & always keep the
power source in a dry place. (Figure 3)
oNOTE: We recommend that you use distilled water to prevent
scale build-up. The first time you operate the pump it can take
up to 5 minutes for the air to be completely expelled and water
to begin flowing properly.
Trouble Shooting & Caution
If you have any questions and/or problems, please contact the retail store you
purchased this fountain.
If your pump fails to run
