Alpine WCT726-UK User manual

Owner’s Manual
Quesons?
Please See Contact Details on the Back!
Tiering Pots Tabletop Fountain
v15.0
USA Item No: WCT726
UK Item No.: WCT726-UK

1
CONTENTS
Contents ...................................................................... 1
What’s Included ........................................................... 2
Features ...................................................................... 3
Specications .............................................................. 3
Assembling & Using Your Product............................... 4
Replacement Parts...................................................... 7
Also Available From Alpine .......................................... 7
Troubleshooting........................................................... 8
Caution ........................................................................ 9
Limited Warranty Information .................................... 10
Notes ..........................................................................11

2
WHAT’S INCLUDED
Fountain
x1
Fountain Pump
x1
*Pump may be packaged separately in an outer box located in the
outer Styrofoam packaging.
Bag of Rocks
x1

FEATURES
3
FEATURES
Can be used
indoors or
outdoors with ETL
listed pump
Flowing water
adds a soothing
sound to any
environment
Made of durable
polystone
SPECIFICATIONS
Country Power
Requirement
Water
Capacity
Tubing Inner
Diameter
USA 120 V, 60 Hz 0.21 gal 0.31"
UK 230V, 50 Hz 0.8 L 7.87 mm

4
ASSEMBLING & USING YOUR PRODUCT
Unpack all components carefully. Check the packaging to ensure all of
the parts have been removed.
*Some splashing may occur when the fountain is in use.
1. Place the Fountain Base on a smooth and level surface. Allow
enough space to access the pump. NOTE: Allow enough space
to access the pump during installation.
2. Remove the pump from its packaging and adjust the ow control
to the lowest setting to avoid splashing until the fountain is
completely assembled.
Alpine Quick Tip #1
Slide to the Left turn up
the water ow. Slide the
adjuster to the Right
to turn down the water
ow.

5
ASSEMBLING & USING YOUR PRODUCT
3. From the back opening of the fountain connect the vinyl tubing
from inside the fountain into the water pump.
4. Gently pour water into the fountain basin, being careful not to
overow and cause splashing. Make sure the water completely
submerges the pump and the water runs clear during operation.
NOTE: We recommend that you use distilled water to prevent scale
build-up. It can take up to 5 minutes for the air to be completely
expelled and water begins to ow the rst time you operate the
pump.
Alpine Quick Tip #2
The black tube
connector may be
attached to the vinyl
tubing or the pump
depending on the
product. It is shown
attached to the pump
here.

6
ASSEMBLING & USING YOUR PRODUCT
5. Plug the pump cord into your local power supply. Make sure that
there is no water around the plug. Always keep the power source
in a dry place.
6. You can now adjust the water pump to your ow preference. (see
Quick Tip #1)
7. Congratulations, your fountain is now complete. Don’t forget to
add water regularly as water will evaporate over time.

7
REPLACEMENT PARTS
ALSO AVAILABLE FROM ALPINE
Country Fountain Care
Formula
Americana®
UV Acrylic
Sealer
Touch-Up
Paint Kit
USA PPL102 RRR106 RTD102
UK N/A N/A N/A
For parts or additional help with your new product, please contact
Alpine customer service.

TROUBLESHOOTING
8
For any questions or problems, contact the retail store where the
fountain was purchased.
If the pump fails to run
1. Check the circuit breaker or plug into a different outlet to be
sure the pump is receiving electrical power.
2. Check the pump discharge and tubing for any kinks and/or
obstructions.
3. Check for any buildup obstructing the water ow and ush it
with a garden hose.
4. Check the rotor by removing the front cover and plate to
access the impeller area, then turn the rotor to make sure that
it is not jammed or broken.
If the pump “spews”
• Check the water level to make sure the pump is completely
submerged and there is enough water in the basin to operate
the fountain. A lack of water causes the pump to spew.
If the pump is abnormally loud
1. Disconnect the pump from the electrical power supply and
remove the front cover and plate.
2. Carefully grip the impeller and gently pull the impeller/rotor
assembly out of the pump housing.
3. Rinse the impeller/rotor assembly and clean the cavity with
clean water. If breakage or damage is found, contact a local
retailer for parts.