Alpine WIN1138 User manual

WIN1138
Tiering Bowls Fountain
with White LED Light
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products including
Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed from the
highest quality materials. In the event that we have not achieved our usual standard of excellence, we
will repair or replace, at our discretion, within the warranty period. A valid proof of purchase, with the
purchase date clearly indicated, must be provided. Photos of defective merchandise will also be
required to help distinguish the actual cause of the defect. Please read below for a detailed
description of warranty coverage.
Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper storage
that allows water to freeze within a product may cause damage and is considered negligence
and will, therefore not be covered under this warranty. The use of “hard water” and/or caustic
cleaners can affect the paint or other finishes. Failure to keep the unit clean, and use of such
additives/cleaners, will also void the warranty. Please note: for fountains, it is normal for some
splashing to occur and protecting the immediate surfaces is not the responsibility of Alpine
Corporation
Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed to protect the entire finish against breakdown
of color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading within the first year from date of
purchase with the above exclusion.
Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you purchased
the product. If that is not an option, you can contact Alpine Corporation at www.alpine4u.com.
When contacting Alpine Corporation, you must be prepared to show proof of purchase,
provide photographs and any other information needed to validate your claim. This may be
necessary to distinguish between a partial or complete replacement of a defective product.
The warranty does not cover any items with multiple parts; the warranty will ONLY cover the
individual component of the unit/item that may be defective. Replacement parts can be made
available to a consumer through the original selling party, or an approved parts retailer. If this
is not an option, contact our customer service department. Item is covered under one year
limited warranty from the date of purchase. When requesting replacement parts due to a
warranty claim after 30 days of purchase, credit card information will be requestedfor shipping
charges.
Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful additives
such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also does not cover
any additional charges or installation, removal, disposal and/or shipping costs or consequential damage
associated with any warranty claim.

Assembling & Using Your Product
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging. Some splashing may occur.
Components:
Fountain
LED Light
Submersible Pump
Transformer
Assembling Instructions:
A. Place the fountain base on a smooth and level surface.
B. Next remove the LED light cord from the opening in the back of the
fountain. Then connect the LED light cord to the transformer by inserting
the male two-prong socket into the female plug of the transformer (see
figure 1 above).
C. Gently pour water into the fountain, being careful not to overflow and
cause splashing. Make sure the water completely submerges the pump
so the water runs clear during operation (see figure 2 above).
D. Plug the cords for the LED lights and pump into your local power supply.
Make sure that there is no water around the plugs and always keep the
power source in a dry place (see figure 4 above).
oNOTE: We recommend that you use distilled water to prevent
scale build-up. The first time you operate the pump it can take
up to 5 minutes for the air to be completely expelled and water
begins to flow properly.
Trouble Shooting & Caution
If you have any questions and/or problems, please contact the retail
store you purchased this fountain.
If your pump fails to run
Check the circuit breaker or try a different outlet to make sure the
pump is receiving electrical power.
Check the pump discharge and tubing for any kinks and/or
obstructions
Any buildup obstructing the water flow can be flushed with a garden
hose
Check the rotor by removing the front cover & plate to access the
impellor area. Turn the rotor and make sure that the rotor is not
jammed or broken
If your pump “spews”
Check the water level to make sure the pump is completely
submerged and there if enough water in the basin to operate your
fountain. Not having enough water will cause your pump to spew
If your pump is making abnormal loud noises
Disconnect the pump from the electrical power supply and remove
the front cover & plate
Carefully grip the impeller and gently pull the impeller/rotor
assembly out of the pump housing
Rinse the impeller/rotor assembly and clean the cavity with clean
water. If breakage or damage is found, contact your local retailer for
part
Fountain Care
We recommend to use Alpine’s all natural cleansing formula to
eliminate foam, lime scale and calcium buildup, fight mineral
deposits, leave water crystal clear, help prevent staining, remove
organic contaminants and treat discolored water. This formula will
help prevent pump damage due to hard water build up.
i. For small sized fountains holding water up to 7liters of
water, we recommend Alpine Item # PPL100
ii. For larger sized fountains holding water over 7liters of
water, we recommend Alpine Item # PPL102
iii. For more information please visit www.alpine4u.com
Caution
oAlways unplug the pump from the electrical outlet
before cleaning & handling
oUse with clean water only, do not place the
fountain and/or parts in any other liquid.
oPeriodically change water & clean the pump to
keep free from micro-organisms
oDisconnect and store the unit in a dry place if not
in use for an extended period of time
oDo not operate with water above 90°F or 30°C
oDo not lift, carry, or pull the pump by the power
cord
oDo not exceed the maximum voltage & wattage on
transformer