Alpine FG101L User manual

FG101L
1 Jet Fogger with 12 LED Lights
Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed
from the highest quality materials. In the event that we have not achieved our usual standard of
excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of
purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper
storage that allows water to freeze within a product may cause damage and is considered
negligence and will, therefore not be covered under this warranty. The use of “hard water”
and/or caustic cleaners can affect the paint or other finishes. Failure to keep the unit clean,
and use of such additives/cleaners, will also void the warranty. Please note: for fountains,
it is normal for some splashing to occur and protecting the immediate surfaces is not the
responsibility of Alpine Corporation
Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed protect the entire finish against breakdown of
color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading within the first year from date of
purchase with the above exclusion.
Procedure/Service
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that not an option, you can contact Alpine Corporation at
www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to
show proof of purchase, provide photographs and any other information needed to
validate your claim. This may be necessary to distinguish between a partial or complete
replacement of a defective product. The warranty does not cover any items with multiple
parts; the warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department. Item is covered under one year limited warranty from the date of
purchase. When requesting replacement parts due to a warranty claim after 30 days of
purchase, credit card information will be requested for shipping charges.
Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim

OPERATION
1. Put the mist unit in your water container.
2. Connect the mist unit to the transformer.
3. Fill so the water level is ¾” above the top of the auto switch (water level
sensor)
4. Plug the transformer into the main power supply.
NOTE: The mist maker only needs TAP WATER, neither distilled water nor pure
water is permitted, otherwise the water-level sensor of the mist maker will not
operate properly when water level is low. This will cause the mist maker to
become exhausted to a point of burn out or function improperly.
GENERAL SUGGESTIONS FOR OPTIMUM USE
1. The mist unit sends up small jets of water while in operation. Your
container should be large enough to prevent water from splashing
outside the container. Do not place the unit where water spillage or
condensation will cause damage to furniture, electronic products or
floors.
2. Use of clean water is recommended. When the water is dirty, change it
with clean water in time (dirty water will affect production the mist).
3. Do not use household abrasive cleaners on any part of the mist unit.
You may clear it with soft cloth in clean water.
MAINTENANCE
1. After operating the mist unit for some time, you may notice a decrease in
the amount of mist produced or it may stop working altogether. At that
time, you should either clean or replace the ceramic disk.
2. Unplug the unit and remove from water container, clean it with soft cloth
in clean water and plug on again. If this doesn’t work, then replace
ceramic disk.
FUNCTION
MODE
COLOR
ORDER
RED
YELLOW
BLUE
STATUS
Single color
1
●
Keep lighting up the set
color
2
●
3
●
Multi-color
4
●
●
5
●
●
6
●
●
All light up
7
●
●
●
Auto-
changing
color
8
1
●
●
●
Auto-changing
color gently, 40 seconds
per cycle.
2
●
●
3
●
4
●
●
●
5
●
●
6
●
7
●
●
●
8
●
9
●
●
9
●
Lights up each color as
modes 1 to 7 step by
step, 3 seconds per step.
●
●
●
●
●
●
●
●
●
●
●
10
Flashing all above modes automatically
0.8 second per step
SAFETY CAUTION
1. Please verify the voltage rate of the transformer with the local power supply
before use. Use the supplied specify transformer.
2. Put the transformer, the connector and the controller which attached on the
cable in a dry place or use indoor only. Take care that no water can get into the
safety transformer, the connector and the controller on the cable along the
supply line.
3. The safety transformer will heat up when in operation. Make sure there is
sufficient air circulation. Do not cover the housing.
4. Keep electrical appliances out of the reach of children.
5. Never touch the water level sensor.
6. When operating, do not let your body parts such as fingers, touch the ceramic or
put on top of it in 4”, which is not dangerous but can cause local pains.
7. Never touch the safety transformer and the mains plug with your wet hands.
8. Always withdraw the mains plug before touching the miniature nebulizer or
remove it from the water.
9. Avoid placing it in the immediate vicinity of electric appliances or water-sensitive
objects because a few water splashes might be produced (but an optimal anti-
splash guard is available).