Alpsat AS07-STCA-4K User manual

1

2
ENGLISH
ENGLISH USER GUIDE INDEX
Safety Instructions
:
3
Technical Specificaitons
:
4
Device Front Rear Side Panel View
:
7
Product Content And Equipments
:
8
Main Menu And Descriptions
:
11
Device Settings
:
13
DVB-S/S2 Satellite Tv Measurement& Settings
:
16
DVB-S/S2 Satellite/Tp Settings
:
19
DVB-S/S2 Satellite Signal Measurement
:
20
DVB-S/S2 Spectrum Analyzsis
:
25
DVB-S/S2 Constellation
:
27
DVB-S/S2 Scan Channel
:
27
DVB-S/S2 Dual Tp Measurement
:
28
DVB-S/S2 Multi-Level Measurement
:
29
DVB-S/S2 Table Search
:
31
DVB-S/S2 Cross Polarity&Auto Port Scan
:
32
DVB-S/S2 Channel List
:
33
DVB-T/T2/Analog Tv Measurement& Settings
:
35
DVB-T/T2 Frequency Plan:
:
36
DVB-T/T2 Signal Measurement
:
39
Terrestrial Analogue Signal Measurement
:
41
DVB-T/T2 Spectrum Analysis
:
43
DVB-T/T2 Constellation Diagram
:
45
DVB-T/T2 Tilt/Limit Measurement
:
46
DVB-T/T2 Table Measurement
:
46
DVB-T/T2 Channel List
:
47
DVB-C/Analogue Measurement & Settings
:
49
DVB-C Frequency Plan
:
50
DVB-C Signal Measurement
:
52
Analogue Cable Tv Signal Measurement
:
54
Cable Tv Spectrum Analysis
:
56
DVB-C Constellation Diagram
:
58
DVB-C Tilt/Limit & Table Measurement:
:
59
DVB-C Channel List
:
60
J.83B Instruction Measurement&Settings
:
62
J.83B (ANNEX.B) Frequency Plan
:
63
J.83B (ANNEX.B) Signal Measurement
:
65
J.83B (ANNEX.B) Spectrum Analysis
:
67
J.83B (ANNEX.B) Constellation Diagram
:
68
J.83B (ANNEX.B) Tilt-Limit Measurement
:
69
J.83B (ANNEX.B) Table Measurement
:
70
J.83B (ANNEX.B) Channel list
:
71
ISDB-T Signal Measurement&Settings
:
73
ISDB-T Frequency Plan
:
74
ISDB-T Signal Measurement
:
76
ISDB-T Spectrum Analysis
:
78
ISDB-T Constellation Diagram
:
79
ISDB-T Tilt-Limit Measurement
:
80
ISDB-T Table Measurement
:
81
ISDB-T Channel list
:
82
Mobile Gsm Signal Settings
:
84
Mobile Gsm Signal Measurement
:
86
CCTV - A/V - Hdmi Input Test And Instructions
:
89

3
ENGLISH
SAFETY INSTRUCTIONS:
Matters to Consider:
To prevent any harm to yourself or your device, strictly follow the instructions below.
Before cleaning your device, unplug the charging cable, turn it off with the Power On/Off
button and clean it with a dry cloth.
Do not use accessories or additional equipment that are not recommended by the
manufacturer of the device, as they may damage the device and void the warranty of the
device. While carrying your device, protect it from impacts and falls, otherwise the device
may be damaged. Be sure to carry your device in its bag and do not carry it in boxes
such as tool bags or with equipment that may be damaged, otherwise the device will be
out of warranty.
Do not use your device outdoors in rainy and snowy weather to protect it from liquid
contact. If you smell smoke, any other smell or hear different sounds from inside the
device, please turn off your device and contact service.
Charge your device with the recommended charging adapter and in-car cigarette lighter
charger. Chargers that are not suitable for use will damage the batteries inside your
device, overheat and explode, and may harm you. These situations are the responsibility
of the user. When using charging adapters, make sure that they are powered by 12Volt-
3000mAh (Center +). Do not leave the device on, the batteries in the device left on will
lose their function over time.
Lighter charger, charging adapter and batteries are not covered by warranty as their
lifespan varies depending on use. Be careful about short circuits when connecting your
device to LNB and antenna amplifiers, otherwise your device may be damaged.
Use suitable low radiation cables for signal input/output, especially when working with
high levels. Only use your device to make measurements in systems whose negatives are
connected to ground potential.
CAUTION: The battery used may present a fire or chemical burn hazard if seriously
mishandled. Under no circumstances should you disassemble the battery, incinerate it or
heat it above 60°C.
Service Related Topics:
Do not try to repair your device yourself. When you open the cover of your device, it will
be out of warranty. For all device-related services, contact your dealer or technical
service.
Use batteries sold or recommended by the manufacturer.

4
AS07STCA-4K
SAT-TERR-CATV FIELD SIGNAL METER
Description:
AS07STCA-4K is a light, portable, ergonomic, user-friendly interface and 4K image processing field
measurement device designed to ensure the best performance of analog and digital TV System
installations. There are also various CCTV (AHD/TVI/CVI), HDMI and CVBS video input features for
system installers. DVB-S/S2 Satellite band, DVB-C Cable TV band (ANNEX A/B/C), DVB-T/T2 Terrestrial
TV band (ISDB-T) and Mobile GSM (2G-3G-4G-5G) bands at 40-2150Mhz covers the range.
AS07STCA-4K measures many digital and analog parameters that installers may need in a fast and
accurate range with various algorithms. It also shows broadcasts in SD-HD-FHD-4K HEVC 10bit video
resolutions on the screen. It enables installers to provide accurate and fast service in all their services
with TV measurement and spectrum Analyzer functions.
GENERAL SPECIFICATIONS
DVB S-S2 / T-T2 / C / J.83B / ISDB-T / GSM MOBILE COMBO Field Signal Analyzer
Single Rf input 40-2150mhz 75 ohm F Connector
20-100dBuV Satellite Band Measurement (± 3 dB Sensitivity)
20-105dBuV Catv-Terr Measurement (± 3 dB Sensitivity)
7” high resolution touch screen
Signal Measurement Screens
Spectrum Analysis Screens
Constellation Screens
Table Measurement screens
Multi Level Measurement Screens
Tilt-Limit Measurement Screens
Rf –aBer –bBer- Per –C/N –Mer –Link Margin Measurement
Video input for AHD-TVI-CVI and Analog CCTV cameras
HDMI In/Out and AV In/Out Capability
H.264, H.265 4K video display
Program List and Audio&Video PID information on one screen.
1.9 GHz High-speed Processor –16GB Memory
7000mAh 7.4V replaceable Lith-Ion battery can work for 3-4 Hours.
Software and frequency plan update via LAN Network 100M or USB
Windows PC software to prepare frequency plan
Programmable 50 Catv Plans, 50 Terresterial Plans, 250 Satellite Memory
10,000 Frequency and Channel Memory
Backlit numeric silicone keypad
Battery protection and the automatic shut-off feature
Led torch light for dark environments
Voltage Test screen for end user testing.
2 kg with battery
Dimensions 250mm X 180mm X 50mm
Operating Range 0 °C to +50 °C
Relative Humidity 90%
With Carrying Bag and Silicone Case
12Volt - 3A Charger and Car charging cable
Menu in 20 Different Languages
Time Zone and Time - Date Setting (no save time settings)

5
DVB-S/S2 FEATURES:
Frequency Band
: 950 –2150 Mhz frequency measurement range
Measuring Range
: 20-100dBuV Satellite Band Measurement (± 3 dB Sensitivity)
Measurement Screens
: RF Power, aBER, bBER, MER, C/N and LINK MARJIN
Memory
: 250 Satellite Memory + 10.000 Channels
MER
: 0 ~ 20dB
Symbol Rate
: 1 ~ 45Ms/s
LNB Supply
: Auto/13V/18V/21V, 500 mA max
Spectrum Analysis
: Spectrum Analyzer with real time and image memory
Span
: 10-20-50-100-200-500-Full Spectrum Span ranges
NIT Search
: Automatic NIT frequency recognition and channel scan on the
Spectrum screen
Multi-Level
: Displaying 4 TP for 1 satellite and 8 TP for 2 satellites in one screen
Dual TP Level
: Ability to measure 2 satellite signals in one screen for Dual Feed lnbs
Diseq-C
: TONE - 1.0 –1.1 –1.2 –2.0 - USALS
Unicable
: UNICABLE I (EN50494) –UNICABLE II (EN50607-dCSS)
LCN
: Yes
LNB
: 34 LNB types and 3 User Defined LNB Types
Power Unit
: dBm, dBuV, dBmV
Table Measurement
: Satellite Frequency Measurement and saving to USB memory as *.cvs
Call
: Single TP / All Satellite / Blind Scan / NIT Scan
Auto Port
: Automatic discovery of Diseq-C ports
Constellation
: QPSK - 8PSK
FEC
: DVB-S:1/2, 2/3, 3/4, 5/6, 7/8 –
: DVB-S2: 1/2, 2/3, 3/4, 5/6, 8/9, 9/10, 2/5, 3/5
Audible Warning
: Warnings based on Power Level
DVB-C & J.83B & DVB-T/T2 & ISDB-T FEATURES
Frequency Band
: 45 –1002 MHz frequency range
Digital Meas. Range
: 25-100dBuV Satellite Band Measurement (± 3 dB Sensitivity)
Analogue Meas. Range
: 20-105dBuV Satellite Band Measurement (± 3 dB Sensitivity)
Digital Meas.Screens
: RF Power, aBER, bBER, MER and LINK MARJIN
Analog Meas. Screens
: RF Power, C/N , Δ V/A
Memory
: 50 Frequency Plans
MER
: 5 ~ 40dB
Antenna Feed
: 5V/12V/20V, 500 mA max
Spectrum Analysis
: Spectrum Analyzer with real time and image memory
Span
: 10-20-50-100-200-500-Full Spectrum Span ranges
NIT Search
: Automatic NIT frequency recognition and channel finding in Spectrum
Constellation
: DVB-C - 16, 32, 64, 128 , 256QAM
J.83B –64, 256 QAM
DVB-T - QPSK, 16, 64QAM
DVB-T2 - QPSK, 16, 64, 256QAM
ISDB-T –DQPSK, QPSK, 16QAM, 64QAM
LCN
: Yes
Power Unit
: dBm, dBuV, dBmV
Table Measurement
: Frequency Plan Measurement and saving to USB memory as *.cvs
Call
: Single Frequency / All Plan
Analogue TV Systems
: M/N/B/G/H/I/D/K/L

6
GSM MOBILE FEATURES
GSM
: 900 MHz
DCS
: 1800 Mhz
UMTS 3G
: 2100 Mhz
4G LTE
: 800 Mhz
5G Low
: 700 Mhz
Signal Meas. Range
: 15-105dBuV Satellite Band Measurement (± 3 dB Sensitivity)
Analog Meas.Screens
: RF Power
Spectrum Analysis
: Spectrum Analyzer with real time and image memory
Span
: 10-25-50-100-Full Spectrum Span ranges
Power Unit
: dBm, dBuV, dBmV
CCTV –A/V –HDMI INPUT FEATURES
ANALOG
: PAL - NTSC AV ıNPUT
AHD
: 1MP, 2MP, 3MP, 4MP, 5MP, 8MP
TVI
: 1MP, 2MP, 3MP, 4MP, 5MP, 8MP
CVI
: 1MP, 2MP, 4MP, 8MP
HDMI IN
: SD –HD - FHD
HDMI OUT
: SD –HD –FHD -4K
AV IN
: PAL - NTSC AV Input
AV OUT
: PAL –NTSC 576p

7
FRONT CONTROL PANEL VIEW
TOP VIEW
SIDE VIEW
7” TOUCH DISPLAY
Silicone
Keypad
Charging LED
Red: Battery
empty
Orange: Battery
is 50% Charged.
Green: Battery
80% Charged
Steady Green:
Battery 100%
Charged
Device Power Led
Red: On
42-2150Mhz Rf Input
Ahd-Tvi-Cvi-Pal
Cctv Input
42-2150Mhz Rf Input
Ahd-Tvi-Cvi-Pal Cctv Input
12V-3A Charge In
SD Card In
USB 2.0 Connection
12V 2A Power Output
White Led Light
Boot Button
HDMI IN/OUT
LAN 100M
AV IN/OUT

8
PRODUCT CONTENT and EQUIPMENT:
1pc AS07STCA-4K Device and Silicone Protection Case:
The product will be protected from harmful effects such as dust, dirt and moisture with the
silicone protection case included in the box with your device. Please do not carry your
device in a toolbox. The silicone protection case is not enough for jamming and hard
impacts. Your device may be out of warranty.
1pc 12V-3A Charger:
You can keep the device constantly charged with your 12 Volt
output electric charging adapter so that you can use your device in
environments where there is no electricity. Keep the charging
adapter away from pinching, impact and overloading. Do not open
to repair or inspect.
1 pc 12 Volt Battery Charger:
You can keep the device constantly charged with your 12 Volt
output battery charging adapter so that you can use your device
in environments where there is no electricity. You can charge your
device while travelling with in-car charging. Keep the 12 Volt
Battery Charger adapter away from pinching, impact and
overloading.

9
1 pc HDMI Cable:
You can test 1080p Video and Audio from external sources with the
HDMI input on your device. The HDMI output also allows you to
transfer the display of the on-screen Signal Measurement menus to
different monitors. This allows you to test HDMI cables and sources.
1 pc A-V Tos Cable:
The AV input on your device allows you to test external Video and
Audio signals. You can also test devices that require focus and
direction adjustment, such as security cameras.
1 pc BNC patch Cable:
You can connect the video inputs of AHD-TVI-CVI-PAL cameras to
the CCTV BNC input on your device and then test the direction,
angle and focus settings.
1pc 12V Output Supply Cable:
This is a patch cable that you can use to supply the camera or RF
amplifier from the 12V-2A output on your device.
2 pcs F-F InterConnector:
Use continuously your F-F Interconnector on your device. The Tuner
input of your device will not be affected by wear, tear and overuse by
only replacing the F-F Interconnector.

10
1 pc F-Male Antenna InterConnector:
You can easily connect cables from Catv and Terr antenna sockets with
the F-Male InterConnector.
1 pc F-Female Antenna InterConnector:
You can easily connect cables from Catv and Terr antenna sockets with
the F-Female InterConnector.
1 pc F Connector Rotation Apparatus:
You can easily turn it with this apparatus in multiswitch and diseqc
connections where the F connector is difficult to rotate.
1 pc Protective Carrying Case:
The Carrying Case and Protection Case protects your device against negative factors such
as dust, dirt and drops. You can safely carry your device in your hand with the side
handle and on your shoulder with the neck strap. You can use it in sunny environments
with the sun visor.

11
MAIN MENU AND DESCRIPTIONS:
STARTING THE DEVICE:
Turn on your AS07STCA-4K device by pressing the POWER ON/OFF button and select the
language you want to use from the box that appears at the first startup. (Warning: If your
device does not react in any case, you can reset it by holding the ON/OFF button for 10-
15 seconds.)
Then, select the time zone you are in or the time zone in which you want to use your
device. In this way, when the device receives the time information together with the signal
from the satellite when the time information is obtained automatically by connecting to the
internet via Lan or when the time information is entered, the measurements made will be
memorized together with the time information.
The screen will then blackout and the MAIN MENU will appear. You can select the systems
you want to measure and the video systems you want to view on this screen.

12
MAIN MENU:
The Main Menu of the AS07STCA-4K device has a user-friendly structure. From the Settings
menu, you can remove function icons that you do not want to appear on the home screen
and change their position on the screen.
1. Help page: It opens the guide page for the function in the current menu.
2. LNB supply: 13/18/22Khz indicates feed on/off position.
3. Led Indicates that the flashlight is working.
4. It becomes visible when the USB is plugged in.
5. It becomes visible when the LAN cable is connected to the network.
6. It indicates the operating time of the device's battery.
7. It indicates the operating charge percentage of the device's battery.
8. DVB-S/S2: Measurement menu for Satellite TV system signals.
9. DVB-C: Measurement menu for cable TV system signals.
10. DVB-T/T2: Measurement menu for terrestrial TV system signals.
11. Settings: You can customize the operation of the device with user-friendly menu.
12. GSM MOBILE: Measurement menu for 5G-4G-3G-2G-Gsm Mobile downlink signals.
13. J.83B: Measurement menu for Cable TV Annex B, TV signal or internet signals.
14. ISDB-T: Measurement menu for terrestrial TV system signals from Japan-Brazil-
Philippines, etc.
15. AHD/TVI/CVI/PAL: Camera setting and test menu with CCTV input.
16. HDMI IN: Test menu for external 1080p HDMI signal.
17. HDMI OUT: Test menu by transferring an HDMI image to a monitor or Display.
18. A/V OUT: PAL video test with AV output.
19. Software version and date: This information will be coloured yellow when new
software is received when the device is connected to the internet via Lan. You can
go to the settings menu and update the software.
20. It will appear in this field when it receives an IP address when the device is
connected to a network via Lan.
Screenshot Note: After put in USB memory , tap left top banner by finger you can get
screenshot to usb memory.

13
AS07STCA-4K DEVICE SETTINGS
LANGUAGE: You can choose from languages such as ENGLISH / TURKISH / GERMAN /
RUSSIAN / ITALIAN / POLISH / ARABIC / PORTOGUSE / SPANISH etc...
AUTO SHUTDOWN 5-10-20-30-30-60 Minutes/Off: if you leave the device on and do not
press any buttons, it will turn off automatically after the time selected in auto power off.
This will protect both your device and battery life.
OSD DELAY: 1-2-3-4-5-10 seconds. You can set how long the OSD menus remain open
on the screen.
KEY LIGHT: You can set how long the backlight of the silicone keypad stays on.
FLASHLIGHT LED POWER: You can change the power of the flashlight in
Min/Medium/Max.
FLASHLIGHT LED DURATION: You can change the duration of the flashlight on for
1/2/3/4/4/5 minutes.
SOUND EFFECTS: You can change the sounds that the device outputs as All / Call Sound
Only / Effects Only / All.

14
ATV SOUNDS: You can adjust the volume level you want to output while showing
terrestrial and cable analogue TV images.
SPECTRUM COLOUR: You can set the colour of the RF level in the spectrum area.
SPECTRUM VIEW: You can show the upper point of the spectrum level as Linear or Full.
TV SYSTEM: It determines the standard to be selected for the device for the channels
found by the Table Search or Automatic Search menus for Analogue TVs.
TIME ZONE: You can adjust all GMT zone settings.
DATE / TIME: The device's Date and Time are set automatically when you watch any
channel, when the LAN cable is plugged in, or the user can set it manually each time the
device is turned on. The device will not memorize the time and date.
DEVICE ID: It shows the serial number of the device.
MAC ID: It indicates the MAC ID defined for the device.
HARDWARE VERSION: It indicates the hardware version of the device.
SOFTWARE VERSION: It indicates the version of the device's software. When the UPDATE
box is active, you can update the firmware.
OPERATING SYSTEM VERSION: It indicates the operating system version of the device.
You can update the device operating system when the UPDATE box is active.
DATABASE VERSION: It shows information about the databases you have used.
EXPORT THE DATABASE FROM THE SERVER: You can quickly update your device's
frequency plans by uploading a ready-made database file containing all the settings and
frequency plan changes for your country or continent from the server to your device.
EXPORT DATABASE FROM USB: You can upload the databases that you have previously
stored or edited in a PC program to your device via USB.
EXPORT DATABASE TO USB: You can save all Satellite, Frequency, Channel, Plans, and
settings used by the device to USB and reuse them later or change them with a PC
program. You can share it with other users and carry different database records for
different regions in your USB Memory.

15
MENU LAYOUT: You can change the location of the boxes in the MAIN MENU according to
your own ease of use and remove the boxes you do not use.
RESET LAYOUT: If you have moved the boxes in the MAIN MENU, reset it, and it will be
as before.
RESTORE FACTORY SETTINGS: You can restore the Satellite, Frequency, Channel, Plans,
and settings on your device to their original state. If you have done a lot of processing
and you don't want to lose this information, you can export your device in its best
condition to a USB memory by appearing EXPORT DATABASE. You can upload this
database to the device after each Factory Reset.
VOLTAGE TEST You can see the supply VOLTAGE values of the electronic circuits that
ensure the stable operation of the device. If it is within the desired values, the boxes will
appear OK in GREEN colour. If you have a problem with your device, you can get
preliminary information and contact the service if there are Red Error messages by going
to this menu.

16
INSTRUCTION FOR USE ON DVB-S/S2 SATELLITE TV MEASUREMENT:
Enter the DVB-S/S2 menu on your AS07STCA-4K using the touchscreen or the direction
and OK buttons on the silicone keypad.
DVB-S/S2 SETTINGS:
Power Unit: You can see the signal levels on the display in dBuV/dBm/dBmV units.
Power Calibration: The margin of error of the measurement levels may increase
depending on ambient temperatures and time of use. You can, therefore, change this
value to plus + or minus - to calibrate the levels closer to the correct level.
Min RF Level: If this is less than the RF level value when measuring the signal, the
correct installation is not confirmed.
Max RF Level: If the RF signal level you set is higher than this value, it may damage the
system or prevent correct distribution.

17
Min MER: When the MER value drops below this level, the device will not confirm that the
installation was done correctly.
Max BER: You can choose how much the Bit Error Rate data rate can be.
Latitude: You can enter the Latitude of your current location.
Longitude: You can enter the Longitude value of your current location.
You can have settings such as the Diseq-C engine automatically processed by entering
these two values according to your location.
LCN Scanning: The device sorts the Channel assignment on the scanned platform
frequencies according to the LCN (logic channel number) value.
SATELLITES: It shows the number of satellites in memory. You can switch to the Satellite
Settings Menu and add, remove, and change the Satellite/TP sequence yourself.

18
LNBs: It shows the number of LNBs in memory. You can switch to the LNB SETTINGS
Menu and change the user LNB settings so you can add an LNB type that is not in
memory.
TRANSPONDER: It shows the number of TPs in memory. You can delete all TPs here.
CHANNELS: It shows the number of CHANNELS in memory. You can delete all Channels
here, reducing the space they occupy in the device's memory.
UNICABLE-I IF LIST: You can set the UB User frequencies of UNICABLE-I in EN50494
standard from this menu.
UNICABLE-II IF LIST: You can set the UB User frequencies of UNICABLE-II in EN50607
standard as Automatic or Manual from this menu.

19
Factory Reset: The device can restore all information in the DVB-S/S2 Satellite menu to
factory defaults.
Note: You can press and hold the ON/OFF button for 10-15 seconds to RESET and restart
the device when the device does not respond to any of the buttons.
SATELLITE/TP SETTINGS:
You can change the order, name, orbit, LNB setting, Diseq-C settings and other parameters
of the Satellite from this menu.
You can add to the satellites in the device's memory with the "NEW" box, delete the current
satellite with the "DELETE" box, and change the name of the satellite by touching the
satellite name.

20
You can add or delete TP frequencies and change the network name and parameter settings
on the satellite you will measure by touching the TP List box.
DVB-S/S2 SATELLITE SIGNAL MEASUREMENT:
Your AS07STCA-4K is capable of measuring DVB-S/S2 - QPSK/8PSK signals. It can also
show SD-HD-FHD-4K TV channels. You can select the satellite, transponder, Diseqc Type
and lnb type you want to adjust your dish antenna or check the signal levels and see the
signal values on the screen. You can also make more detailed settings with the
SPECTRUM and CONSTELATION box.
SATELLITES: The satellite names in the device's memory will respectively be shown when
you touch the box or press the OK button. You can add new satellites or change this
order in the Satellite/TP Settings menu.
TP: It shows the TPs on the satellite you have selected. You can change TPs with the
right and left buttons or by touching the box.