ALTA BLISS User manual

U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development
Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. Le présent appareil est conforme aux CNR d’ISED
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
FCC SAR Warning:
RF Exposure Information (SAR): The SAR limit of USA (FCC)is 1.6W/Kg averaged
over one gram of tissue.
Product Type: BLISS Bridge (FCC ID: 2AU29AMPRFWIFIUSB) has also been tested
against this SAR limit. The device was tested for typical body-worn operations to
keep the BLISS Bridge at least 5mm from the body. When worn on body must be
correct back clip for this product, use of non-approved accessories may result in
exposure levels which exceed the uncontrolled environmental RF exposure limits.
FCC SAR Warning:
The SAR limit of IC is 1.6W/Kg averaged over one gram of tissue.
Product Type: BLISS Bridge, model number: BLISS Bridge Wi and RF (IC:
25624-AMPRFWIFI) has also been tested against this SAR limit. The device was
tested for typical body-worn operations to keep the BLISS Bridge at least 5mm
from the body. When worn on body must be correct back clip for this product,
use of non-approved accessories may result in exposure levels which exceed the
uncontrolled environmental RF exposure limits.
Le SAR de IC est limité à 16w / kg, avec une moyenne par gramme. Produits Type:
BLISS Bridge, type: BLISS Bridge Wi and RF (IC: 25624-AMPRFWIFI) a également
été testé pour la limite SAR. Ce dispositif est utilisé pour tester des opérations d
‘usure corporelle typiques et des opérations en direction du Haut de physique,
de manière à maintenir une distance d’ au moins 5mm entre le BLISS Bridge et le
visage. Osure.`
Quick Start Guide for
AMP USB Bridge
AMP USB Bridge allows the user to link their motorized S hades , B linds,
and Draperies into a Wi-Fi network, enabling control via smart APP and
interaction with other IoT products.
S tep 1 Down load A PP
Please scan the QR c ode below .
Step 2
Please scan the QR c ode below to learn more about linking the AMP USB Bridge
with your home Wi-Fi router, setting up the AMP APP, and establishing a connection
with other IoT applications.
Product
Certication
Quick Start Guide for
AMP USB Bridge
AMP USB Bridge allows the user to link their motorized S hades , B linds,
and Draperies into a Wi-Fi network, enabling control via smart APP and
interaction with other IoT products.
S tep 1 Down load A PP
Please scan the QR c ode below .
Step 2
Please scan the QR c ode below to learn more about linking the AMP USB Bridge
with your home Wi-Fi router, setting up the AMP APP, and establishing a connection
with other IoT applications.
Product
Certication
Quick Start Guide for
AMP USB Bridge
AMP USB Bridge allows the user to link their motorized S hades , B linds,
and Draperies into a Wi-Fi network, enabling control via smart APP and
interaction with other IoT products.
S tep 1 Down load A PP
Please scan the QR c ode below .
Step 2
Please scan the QR c ode below to learn more about linking the AMP USB Bridge
with your home Wi-Fi router, setting up the AMP APP, and establishing a connection
with other IoT applications.
Product
Certication
BLISS BRIDGE
QUICK START GUIDE
TM
Declarations Step 1
Step 2
The BLISS Bridge allows users to link their motorized shades and blinds into a Wi-Fi
network enabling control via smart APP and interaction with other IoT products.
Please scan the QR Code below to download the BLISS app.
Please scan the QR Code below for additional videos on linking the BLISS
Bridge with your home Wi-Fi router, setting up the BLISS app, and establishing
a connection with other IoT applications.
Quick Start Guide for
AMP USB Bridge
AMP USB Bridge allows the user to link their motorized S hades , B linds,
and Draperies into a Wi-Fi network, enabling control via smart APP and
interaction with other IoT products.
S tep 1 Down load A PP
Please scan the QR c ode below .
Step 2
Please scan the QR c ode below to learn more about linking the AMP USB Bridge
with your home Wi-Fi router, setting up the AMP APP, and establishing a connection
with other IoT applications.
Product
Certication
Scan the QR code to
get the app on
Google Play.
Scan the QR code to
download the app on
on the Apple Store.

BLISS BRIDGE USB
TM
Product Parameter
Status Indicator
LED Indicator
Programming
Button
Programming / Pairing
Press and hold programming button for about 2 seconds, then release until the LED
blinks purple.
Reset
Press and hold programming button for about 10 seconds, then release until the LED
blinks red.
Input Voltage 5V DC (USB Type A)
Input Power 1000mA
WiFi Network 2.4Ghz only (802.1 1b/n/g)
Shade Control Frequency 433.92 Mhz
Range 30 meters or 98 feet
Protection Class IP20
Operation Temperature 32˚F to 104˚F (0˚C to 40˚C)
Status Indicator
Color Duration
Meaning
Constant
Continuously till status change
Continuously till status change
5 times
Continuously till status change
Continuously till status change
Working fine
Wi-Fi is disconnected
Wi-Fi is connected
Bridge reset
Pairing underway
Upgrade in progress
Constant Blue
Slow Flashing Red
Slow Flashing Yellow
Quick Flashing Red
Slow Flashing Purple
Slow Flashing Green
Product Parameter
Indoor use only
Wi-Fi: 2.4GHz (802.11b/n/g)
Power Input:
DC 5V/1A (USB Type-A )
Radio frequency: 433.92MHz
Working temperature: 0℃~ 40 ℃
Dimension(mm)：L132.2 * W75 * H36
Program Button
Program / Pairing:
Press and hold program button for about 2 seconds, then release until the LED blinks purple.
Reset:
Press and hold program button for about 10 seconds, then release until the LED blinks red.
Indicator
90°
Folds 90 degrees