ALTRACO NT-AT User manual

Electric Water Tape
Dispenser Manual
MODEL: NT-AT
VERSION: 202101

CONTENTS
SAFETY NOTICE
DISPENSER PARAMETERS
STRUCTURE INTRODUCTION
KEYPAD OPERATION INSTRUCTION
ROLL GUIDE INSTALLATION INSTRUCTION
TAPE INSTALLATION INSTRUCTION
UPPER TAPE PLATE INSTALLATION INSTRUCTION
BRUSH OPERATION INSTRUCTION
WATER BOTTLE OPERATION INSTRUCTION
MAINTENANCE INSTRUCTIONS
-1-
2
2
3
4
5
5
6
6
7
7

-2-
SAFETY NOTICE
Please use 200-230V power supply.
Avoid placing in direct sunlight and outdoors.
Please cut off the power quickly when break down.
Please disconnect the power supply and remove the plug , when cleaning or
repairing equipment.
Do not disassemble or repair equipment without the knowledge of engineer.
DISPENSER PARAMETERS
Voltage
Power
Speed
Weight
Size
200-230V
200W
30CM/S
12KG
45*32*28CM

-3-
2.Manual handle
1.Roll guides
for shear blade
4.Drive wheel
3.Lower platen
5.Shear Blade
6.Heating equipment
7.Brush pressure adjusting device
STRUCTURE INTRODUCTION
1.Top Cover
2.Operating Guide
5.Water Bottle
3.Brush Assembly
4.Water Tank

-4-
KEYPAD OPERATION INSTRUCTIONS
Temperature Control button
H: 0 without temperature.
H: 1-5 different temperature ranges.
Summer setting: H-3 \ Winter setting: H-5
Auto continuous mode
Pressing the AUTO button, then press any value, the tape
is dispensed, and the same length tape will be
automatically dispensed. Press the AUTO button again to
cancel the automatic mode.
Double length button
2X Button Doubles selected length.
For example, to dispense 30CM tape, first press the 2X
Button, then press the button 15.
Programming mode
For example, to continuously dispense
different sizes: 15-35-55CM.
First press the SET button to enter the programming mode;
Pressing the button accordingly: 15, 35, 55.
Press the ENT button to confirm and press the START
button start to dispense.
Press the SET button again to cancel the
programming mode.
Length adjustment button
Press and hold the
manual feed button
the tape is dispensed
continuously.
Plus button adds 1 cm to selected length.
Minus button subtracts 1 cm from selected length.
For example, to dispense 17CM tape, press the plus
button twice, and then press the button 15.
Gear
Temperature
1
18°
2
36°
3
54°
4
72°
5
90°
015
SET HOI
95
105
75
85
55
65
35
45
15
25
START
REPEAT
AUTO
2X
ENT
SET
AUTO

-5-
1
2
3
1
ROLL GUIDE INSTALLATION INSTRUCTION
According to the actual tape width, install the roll guides at its proper position.
See Figure 1, Insert the upper part of the roll guide into the front slot.
See Figure 2, Insert the lower end of the roll guide into the front slot.
See Figure 3, Insert the roll guide into the bottom slot.
TAPE INSTALLATION INSTRUCTION
See Figure 1, pass the tape around the lift roller and pull it to the Drive wheel (Caution: Cut
the end of the tape so that it has a clean, square end to feed under the drive wheel)
Pass the tape through the upper guide wheel and push it to the cutter.

-6-
1
2
3
1
2
3
4
UPPER TAPE PLATE INSTALLATION INSTRUCTION
Check the upper tape plate if is in its proper position.
Install the Upper Tape Plate as shown below.
BRUSH OPERATION INSTRUCTION
As shown in Picture 1, first take out the water box to fill it with water, then take out
the water tank.
As shown in Picture 2, water the top surface of the brush until the brush is completely soaked.
As shown in Picture 3, put back the water box, and then put back the water tank.
As shown in Picture 4, gently press down the red part with your hand to make it fully contact
with the brush.

-7-
1
2
1
2
WATER BOTTLE OPERATING INSTRUCTION
Fill the bottle with water and place its proper position.
The water level in the water tank can be adjusted at the positionshown in Figure 1.
Normally, the water level is adjusted to the highest level.
Caution: Pay attention to the amount of water remaining in the water bottle
when using. Make sure the brush stays wet.
MAINTENANCE INSTRUCTIONS: ACCORDING TO THE ACTUAL USE TIME, REGULAR
MAINTENANCE
As figure 1 show, clean and inject lubricant once a month.
Picture 2 If a paper jam is found, the amount of water applied is small or uneven, the
tightness of the two screws indicated by the arrows can be adjusted.
The first time you use the tape, the sticky side of the tape has too little moisture. Please
cut off several pieces of tape multiple times.