Altronix Trove2AM2 User manual

Installation Guide
Versatile Access Power and Integration Enclosures
Trove2AM2 TAM2
- Trove2 enclosure with - Altronix/AMAG backplane only
Altronix/AMAG backplane (TAM2)
Overview:
Trove2AM2 accommodates various combinations of AMAG boards with or without Altronix power supplies and accessories for access systems.
Specifications:
Backplane Accommodates a Combination of the Following:
• Two (2) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB, or eFlow104NB.
• One ACM4(CB), ACM8(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6.
• M2150 2DC, M2150 4DC, M2150 AC24/4, M2150 2DBC, M2150 4DBC, or M2150 8DBC.
Installation Instructions for Trove2:
1. Remove backplane from enclosure prior to mounting (do not discard hardware).
2. Mark and predrill holes in the wall to line up with the top keyholes in the enclosure. Install the upper fasteners and screws in the wall
with the screw heads protruding. Place the enclosure’s upper keyholes over the screws; level and secure. Mark the position of the
lower holes. Remove the enclosure. Drill the lower holes and install the fasteners. Place the enclosure’s upper keyholes over the
upper screws. Install the lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8).
3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent) in desired location, opposite hinge.
Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 1).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount Altronix/AMAG boards to backplane, refer to pages 2-4.
Hardware:
Edge of
Enclosure
to Access Control Panel
or U.L. Listed
Reporting Device
Enclosure
Honeywell
model # 112
Tamper Switch
or equivalent
(provided)
Fig. 1
All registered trademarks are property of their respective owners.
Trove2AM2
- Trove2 enclosure with TAM2 Altronix/AMAG backplane.
• Includes: tamper switch, cam lock, lock nuts and
mounting hardware.
• 16 Gauge grey enclosure with ample knockouts for
convenient access.
Enclosure Dimensions (H x W x D):
27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm).
TAM2
- TAM2 Altronix/AMAG backplane.
• 16 Gauge backplane.
• Includes mounting hardware.
Dimensions (H x W x D):
25.375” x 19.375” x 0.3125” (644.6mm x 492.1mm x 7.9mm).
Metal or Nylon Standoff
5/16” Pan Head Screw
Lock Nut
TAM2_Rev. 062216

- 2 - Trove2AM2
Pem
Standoff
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 2a
TAM2: Configuration of Altronix Power Supply and/or Sub-Assembly Boards and
AMAG Boards AMAG M2150 2DC and M2150 2DBC
1. Fasten standoffs (provided) to pems that match the hole pattern for Altronix Power Supply/Chargers or Altronix Sub-Assembly boards
(Fig. 2, 2a, pg. 2). Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 2, pg. 2).
2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, pg. 2).
3. Align the AMAG boards on the backplane to match the boards’ mounting holes with pems provided.
4. Fasten standoffs (provided) to pems that match the hole pattern for AMAG M2150 2DC and 2150 2DBC boards.
5. Mount AMAG boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, pg. 2).
Note: AMAG M2150 2DC boards have specific markings.
Please orient boards in the appropriate position according to the Fig. 2 below.
6. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Fig. 2
Altronix
Power Supply
AMAG
M2150 4DC
AMAG
M2150 2DBC
AMAG
M2150 4DBC,
M2150 8DBC
READER 1
READER 1
COM C
RS232
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
Altronix
Power Supply
AMAG
M2150 AC24/4
AMAG
M2150 4DBC,
M2150 8DBC
READER 1
COM C
RS232
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
Altronix
Power Supply
AMAG
M2150 2DC
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly

Trove2AM2 - 3 -
Altronix
Power Supply
AMAG
M2150 4DC
AMAG
M2150 2DBC
AMAG
M2150 4DBC,
M2150 8DBC
READER 1
READER 1
COM C
RS232
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
Altronix
Power Supply
AMAG
M2150 AC24/4
AMAG
M2150 4DBC,
M2150 8DBC
READER 1
COM C
RS232
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
Altronix
Power Supply
AMAG
M2150 2DC
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
TAM2: Configuration of Altronix Power Supply and/or Sub-Assembly Boards and
AMAG Boards AMAG M2150 4DC, M2150 4DBC, and M2150 8DBC
1. Fasten standoffs (provided) to pems that match the hole pattern for Altronix Power Supply/Chargers or Altronix Sub-Assembly boards
(Fig. 3, 3a, pg. 3). Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 3, pg. 3).
2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 3, pg. 3).
3. Align the AMAG boards on the backplane to match the boards’ mounting holes with pems provided.
4. Fasten standoffs (provided) to pems that match the hole pattern for AMAG M2150 4DC, M2150 4DBC, and M2150 8DBC boards.
5. Mount AMAG boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 3, pg. 3).
Note: AMAG M2150 4DBC and M2150 8DBC boards have specific markings.
Please orient boards in the appropriate position according to the Fig. 3 below.
6. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Fig. 3
Pem
Standoff
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 3a

- 4 - Trove2AM2
Altronix
Power Supply
AMAG
M2150 4DC
AMAG
M2150 2DBC
AMAG
M2150 4DBC,
M2150 8DBC
READER 1
READER 1
COM C
RS232
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
Altronix
Power Supply
AMAG
M2150 AC24/4
AMAG
M2150 4DBC,
M2150 8DBC
READER 1
COM C
RS232
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
Altronix
Power Supply
AMAG
M2150 2DC
Altronix
Power Supply or
Sub-Assembly
Metal Standoff Placement
Metal Standoff Placement
Altronix
Sub-
Assembly
TAM2: Configuration of Altronix Power Supply and/or Sub-Assembly Boards and
AMAG Boards AMAG M2150 AC24/4, M2150 4DBC, and M2150 8DBC
1. Fasten standoffs (provided) to pems that match the hole pattern for Altronix Power Supply/Chargers or Altronix Sub-Assembly boards
(Fig. 4, 4a, pg. 4). Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 4, pg. 4).
2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 4, pg. 4).
3. Align the AMAG boards on the backplane to match the boards’ mounting holes with pems provided.
4. Fasten standoffs (provided) to pems that match the hole pattern for AMAG M2150 AC24/4, M2150 4DBC, and M2150 8DBC boards.
5. Mount AMAG boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 4, pg. 4).
Note: AMAG M2150 4DBC and M2150 8DBC boards have specific markings.
Please orient boards in the appropriate position according to the Fig. 4 below.
6. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Fig. 4
Pem
Standoff
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 4a

- 5 - Trove2AM2
Notes:

- 6 - Trove2AM2
Notes:

- 7 - Trove2AM2
7.5”
(190.5mm)
7.5”
(190.5mm)
7.5”
(190.5mm)
25.375”
(644.6mm)
19.375”
(492.1mm)
12.625”
(320.7mm)
0.45”
(11.4mm)
1.0” (25.4mm)
1.0” (25.4mm)
9.2”
(
233.7mm
)
8.5”
(215.9mm)
16.25”
(412.8mm)
0.156”
( 3.96mm)
9.2”
(
233.7mm
)
7.5”
(190.5mm)
0.45”
(11.4mm)
TAM2 Dimensions (H x W x D):
25.375” x 19.375” x 0.3125” (644.6mm x 492.1mm x 7.9mm)

- 8 - Trove2AM2
Trove2 Enclosure Dimensions (H x W x D approximate):
27.25” x 21.75” x 6.5” (692.15mm x 552.5mm x 165.1mm)
G
1.25”
(31.75mm)
1.25”
(31.75mm)
6.25”
(158.75mm)
6.25”
(158.75mm)
6.75”
(171.45mm)
8.25”
(209.54mm)
8.00”
(203.2mm)
1.5”
(38.1mm)
1.25”
(31.75mm)
0.85”
(21.59mm)
0.85”
(21.59mm)
1.00”
(25.4mm)
2.00”
(50.8mm)
1.25”
(31.75mm)
2.00”
(
50.8mm
)
2.00”
(
50.8mm
)
5.25”
(
133.35mm
)
5.25”
(
133.35mm
)
7.00”
(
177.79mm
)
2.00”
(50.8mm)
2.00”
(50.8mm)
27.00”
(685.8mm)
3.50”
(88.9mm)
0.5625”
(14.29mm)
2.415”
(61.34mm)
0.685”
(17.399mm)
1.77”
(44.96mm)
3.50”
(88.9mm)
21.50”
(546.1mm)
19.80”
(502.92mm)
5.25”
(133.35mm)
5.25”
(133.35mm)
0.885” (22.479mm)
1.125” (28.32mm)
Knockouts
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [email protected] | Made in U.S.A.
IITrove2AM2 J31Q
MEMBER