Altronix Trove1V1R User manual

Rev. TVR112818
Trove1V1R
- Trove rack enclosure with Altronix/HID VertX®backplane (TV1R)
Installation Guide
All registered trademarks are property of their respective owners. More than just power.™
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
Access & Power Integration

- 2 - Trove1V1R
Overview:
Altronix Trove1V1R rack mount access & power integration solution accommodates various combinations of HID VertX®boards with or without Altronix
power supplies and accessories for access systems.
Specifications:
Backplane Accommodates a Combination of the Following:
• Up to two (2) eFlow4NB, eFlow6NB, eFlow102NB, eFlow104NB, ACMS8(CB) or ACM8(CB).
• Up to three (3) ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), or VR6.
• Up to six (6) V100, V200, V300, V1000 or V2000.
Assembling and Attaching Z Bracket Wire Management Accessory (included):
Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Ten (10) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard hardware (included)
(Fig. 1, pg. 2).
2. Attach arms to each other using bolts and
lock nuts (Fig. 1a, pg. 2).
3. Attach the hinge brackets to the ends of
arms using bolts and nuts positioning
them as shown on Fig. 1b, pg. 2.
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts (included) (Fig. 2, 2a, pg. 2).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).
Agency Listings:
• CE European Conformity.
Trove1V1R
Trove1R rack mount enclosure with
TV1R Altronix/HID VertX®backplane.
• 16 Gauge black enclosure with ample knockouts for convenient access.
• Includes: tamper switch, cam lock and mounting hardware.
Modular 2U standard EIA 19” drawer with extendable slides up to 48”.
• Dimensions (H x W x D): 3.25” x 19.0” x 26.5”
(82.6mm x 482.6mm x 673.1mm).
TV1R
Altronix/HID VertX®backplane.
• 16 Gauge backplane.
• Dimensions (H x W x D): 18.5” x 15.25” x 0.3125”
(469.9mm x 387.4mm x 7.9mm).
Optional Accessories:
• RE2: Rack Mount Battery Enclosure accommodates up to four (4)
12VDC/7AH batteries
• WM5, WM25, WM100: Magnetic Cable Tie Mounts (5, 25, 100 counts).
• LC3: 6 ft. three-wire line cord.
Two (2)
Fig. 1
Fig. 2
Fig. 2a
Fig. 1b
Fig. 1a

Trove1V1R - 3 -
Installation Instructions for Trove1R:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure prior to installing into rack cabinet
(do not discard hardware).
2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the
enclosure upside down. Punch out the knockout in designated location, on the back of the unit, from
outside of the drawer (Fig. 3, pg. 3). Insert the tamper switch into the knockout from outside of the drawer
with the button facing outwards and spaded connectors inside the drawer. Connect tamper switch wiring to the
Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.
3. Slide the Trove rack enclosure into an open 2U location in the rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Make sure that all internal cofigurations (wiring, voltage selection, switch settings, etc.) are complete
before mounting backplane back into enclosure.
7. After all components are mounted on the backplane, attach it to the enclosure using included hardware.
TV1R: Configuration of Altronix Power Supply and/or Sub-Assembly Boards
1. Fasten standoffs onto metal pems configuration (A) or (B) of backplane depending on the power supply and/or Sub-Assembly (Fig. 4, pg. 3).
2. Position access controller module over corresponding standoffs and fasten screws into standoffs (Fig. 4a, pg. 3).
3. Mount backplane to enclosure with hardware.
Position Chart for the Following Models:
Altronix Power Supply/Charger or Sub-Assembly Pem Mounting
eFlow4NB, eFlow6NB, eFlow102NB, eFlow104NB, ACMS8(CB), or ACM8(CB) A
ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), or VR6 B
Fig. 4
B
B
B
AMetal
Standoff
Placement
for Altronix
Power
Supplies
AMetal
Standoff
Placement
for Altronix
Power
Supplies
Pem
Standoff
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 4a
Fig. 3
Tamper Switch mounting location
Back of the drawer,
viewed from outside.

- 4 - Trove1V1R
TV1R: Configuration of HID VertX®Boards
1. Fasten standoffs onto metal pems configuration (A) of backplane (Fig. 5, pg. 4).
2. Position access controller module over corresponding standoffs and fasten screws into standoffs (Fig. 5a, pg. 4).
3. Mount backplane to enclosure with hardware.
Access Controller Position Chart for the Following Models:
HID VertX® Sub-Assembly Pem Mounting
V100
A
V200
V300
V1000
V2000
Fig. 5
A
A
A
A
A
A
Pem
Standoff
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 5a

Trove1V1R - 5 -
Notes:

- 6 - Trove1V1R
Notes:

Trove1V1R - 7 -
TV1R Enclosure Dimensions (H x W x D):
18.5” x 15.25” x 0.3125” (469.9mm x 387.4mm x 7.9mm)
15.25” (387.4mm)
18.5”
469.9mm

- 8 - Trove1V1R
Trove1R Enclosure Dimensions (H x W x D):
3.25” x 19.0” x 26.5” (82.6mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.
3.25”
82.3mm
26.5”
673.1mm
19” (482.6mm)
2.4”
61mm
4.57”
116.1mm
11.175” (283.8mm)
R 1.27” (32.3mm)
1” (25.4mm)
0.55” (14mm)
3.62”
92mm
0.1”
2.5mm
1.5”
38.1mm
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [email protected] | Made in U.S.A.
IITrove1V1R L12R
MEMBER