Altronix NetWay112 User manual

Rev. 100614
Installation Guide
NetWay112
®
Single Port PoE Injector for Standard NetWork Infrastructure
Overview:
Altronix NetWay112 is a single port PoE injector which provides power and passes data (e.g. video) for
PoE compliant devices. Devices may be located up to 100m from NetWay112. To extend data distance
for an additional 100m use NetWayXT/NetWayXTX repeater modules.
Features:
Agency Listings:
• UL/CUL Listed for Information Technology
Equipment (UL 60950-1).
• CE approved.
Input:
• 12VDC/1.5A to 16VDC/1.1A.
Data:
• One (1) PoE port provides power and passes
data over ethernet (CAT5) cable up to 100m.
• Data rate: 10/100 Base-T compliant.
PoE:
• IEEE 802.3af (15W) compliant.
Features:
• Port status LED.
• PoE manual shutdown feature allows for
cameras and/or edge devices to be reset.
For UL 60950-1 applications only
(see Technical Specifications table pg. 4).
• Auto detection and protection of legacy
non-PoE cameras/devices.
• Data rate: 10/100 BASE-T compliant.
• Compact insulated housing.
• Spring terminals (Input and PoE shutdown).
Dimensions (W x L x H approx.):
2.5” x 3.8” x 1”
(63.5mm x 96.52mm x 25.4mm).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all
local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire
suitable for the application.
Unit is intended to be used with a UL Listed Class 2 or LPS (limited power supply). NetWay112 is
not intended to be connected to outside plant leads and should be installed indoors within the protected
premises. NetWay112 is intended for indoor use only.
1. Mount NetWay112 in desired location utilizing the mounting hole (Fig. 1a, pg. 2).
Use a proper fastener and/or wall anchor when securing NetWay112 with screw through its
mounting hole to the wall.
2. Connect UL Listed Class 2 or LPS (limited power supply) providing 12VDC/1.5A to 16VDC/1.1A
to terminals marked [+ DC --- Input], carefully observing polarity (Fig. 1b, pg. 2).
Use 22AWG - 16AWG wire for this connection.
Input power should be a Access Control power supply or a transformer.
3. Connect structured cable from port marked [IN] on NetWay112 to the corresponding input of an
UL Listed ethernet switch or video server (Fig. 1b, pg. 2).
4. Connect structured cable from port marked [OUT] on the NetWay112 to the PoE device (Fig. 1b, pg. 2).
5. Port status LED will illuminate indicating normal operation (Fig. 1c, pg. 2).
6. To initiate PoE shutdown connect 12VAC to 24VAC or 5VDC to 24VDC to the input terminals marked
[Power Shutdown] on the NetWay112 (Fig. 1b, pg. 2). The PoE output voltage may be shut down by
manually applying voltage in the rated range (PoE Shutdown Voltage Range in Specifications). Upon
applying voltage, the output will drop to zero volts. Removal of voltage from the shutdown terminals
or applying zero volts to the shutdown terminals will allow the PoE output to operate normally to
supply power to PoE compliant devices.
Note: Return to normal operation from shutdown can take about 4 seconds. Although there is no
output voltage to power PoE devices during shutdown, data signals may still be present on the data
pair lines of the CAT5 cable.
Installing a NetWay1512 adapter for 12VDC IP cameras up to 13W:
1. Mount NetWay1512 in the proximity of IP camera (Fig. 3, pg. 3). Use velcro (supplied).
2. Connect structured cable from port marked [IN] on NetWay1512 to port marked [OUT] of
NetWay112 (Fig. 3, pg. 3, Fig. 1b pg. 2).
3. Connect structured cable from port marked [OUT] on NetWay1512 to the IP camera/device
(Fig. 3, pg. 3, Fig. 1b pg. 2).
4. Connect 12VDC output from NetWay1512 terminals marked [+ 12VDC --- ] to the power input of
the IP camera (Fig. 3, pg. 3). Polarity must be observed.
5. Power LED indicator will illuminate on NetWay1512 under normal conditions (Fig. 3, pg. 3).
NetWay112 - 1 -
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Structured
Cable from
Network
Switch
12-16VDC
Input
+ ---
12VAC to 24VAC or
5VDC to 24VDC Input
for PoE shutdown
Structured Cable from
IP Camera, IP Lock or IP device,
NetWay1512 or NetWayXT
+ DC ---
Input Power ShutdownIN OUT
NetWay112
Single Port Injector (Midspan)
12VDC, 1.6A Input
48VDC 15.4W max. per IEEE 802.3af
www.altronix.com
I.T.E. 43KC
Fig. 1
Structured
Cable from
Network
Switch
12-16VDC
Input
+ ---
Structured Cable from
IP Camera, IP Lock or IP device,
NetWay1512 or NetWayXT
+ DC ---
Input Power ShutdownIN OUT
Port
Status
NetWay112
Single Port Injector (Midspan)
12VDC, 1.6A Input
48VDC 15.4W max. per IEEE 802.3af
www.altronix.com
I.T.E. 43KC
Port
Status
Fig. 1a Fig. 1b
Fig. 1c
12VAC to 24VAC or
5VDC to 24VDC Input
for PoE shutdown
NetWay112 Port Status and LED Flash Codes
Port Status Flash Code Flash Pattern
Non-Powered Device
0Ω< RPORT < 200ΩOFF LED OFF
Port Open RPORT > 1MΩOFF LED OFF
Port On 25kΩON LED ON
Low Signature Resistance
300Ω< RPORT < 15kΩ1 Flash Z l l l Z l l l Z l l l
High Signature Resistance
33KΩ< RPORT < 500kΩ2 Flashes Z Z l l Z Z l l Z Z l l
Port Overload Fault 5 Flashes l l l l Z Z Z Z Z l l l l
Installing a NetWayXT/NetWayXTX repeater module:
NetWayXT will work only with PoE devices.
NetWayXTX will work with PoE/PoE+ devices.
1. Mount NetWayXT/NetWayXTX in desired location utilizing the mounting hole (Fig. 4, pg. 3). Use
a proper fastener and/or wall anchor when securing NetWayXT/NetWayXTX to the wall.
2. Connect structured cable from port marked [OUT] on NetWay112 to port marked [IN] on the
NetWayXT/NetWayXTX (Fig. 4, pg. 3, Fig. 1b, pg. 3).
3. Connect structured cable from port marked [OUT] on NetWayXT/NetWayXTX to the PoE camera/
edge device or next NetWayXT/NetWayXTX repeater (Fig. 4, pg. 3).
4. Port status LEDs will illuminate on NetWayXT/NetWayXTX indicating the port is operational
(Fig. 4, pg. 3, refer to Port LED definitions on pg. 2).
5. Power LED will illuminate indicating 12VDC output.
Port LED definitions for NetWayXT repeater:
Status Green LED Yellow LED
OFF Indicates it is connected as 10Base-T or no link. Indicates no link.
ON Indicates it is connected as 100Base-TX. Indicates a link.
Blinking --------------------------- Indicates activity.
Port LED definitions for NetWayXTX repeater:
Status PoE/PoE+ Output LED PoE/PoE+ Input LED Yellow LED
OFF No PoE/PoE+ Output No PoE/PoE+ Input Indicates no link.
ON Normal PoE/PoE+ Output PoE/PoE+ Input Indicates a link.
Blinking ------- ------- Indicates activity.
- 2 - NetWay112
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Fig. 3 Fig. 4
www.altronix.com
IN OUT
Netway1512
Adapter
12VDC
+ Output ---
+ --
12VDC
Power to
Camera/Device
Structured
Cable from
NetWay112
Structured Cable
from IP Camera/Device
I.T.E.
43KC
NetwayXT
Repeater
www.altronix.com
IN
OUT
Power
Power
LED
NetWayXTX
NetWayXT
Structured
Cable from
NetWay8/16
Structured Cable
to IP Camera/
Edge Device
or next
NetWayXT
Structured
Cable from
NetWay8/16
PoE/PoE+
Output
LED
Structured Port Status PoE/PoE+
Cable to LEDs Input
PoE/PoE+ LED
Camera/Device or
next NetWayXTX
Typical Applications:
Fig. 5 - Typical Access Control application.
Network Switch PC/Server
CAT5e
100m
UL Listed
Access Control
Power-Limited
Power Supply
12VDC - 16VDC
Card
Reader
Electric
Strike
HID
Solo Edge
Device
Netway112
Fig. 6
Port shutdown PoE Camera
Netway112 input
CAT5e
100m
12VDC -
16VDC
input Network Switch NVR/Network Server Video Monitor
Fig. 7
NVR/Network Server
NetWay1512
Network Switch
12VDC
IP Camera
CAT5e
100m
Port shutdown
input
Video Monitor
Netway112
12VDC -
16VDC
input
Fig. 8
Netway112
Port shutdown
input NetwayXT CAT5e additional
100m
CAT5e
100m
PoE Camera
12VDC -
16VDC Network Switch NVR/Network Server
input
Video Monitor
NetWay112 - 3 -
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Maintenance:
Unit should be tested at least once a year for the proper operation as follows:
While the NetWay112 is powered and the output is connected to a suitable UL Listed PoE device, it
should be tested for PoE shutdown operation (For UL 60950-1 applications only).
Troubleshooting:
Refer to NetWay112 Port Status and LED Flash Codes, pg. 2.
Technical Specifications:
Parameter Description
No. of Ports One (1)
Input power
requirements 12VDC to 16VDC @ 1.5A to 1.1A.
Indicators Port Status LED.
PoE Shutdown
Voltage and
Current Range
5VDC to 24VDC or 12VAC to 24VAC
Maximum current: 2mA for 5VDC
Maximum current for higher voltages: 10mA
Environmental
Conditions
Operating Ambient Temperature: UL60950-1: -40ºC to 50ºC (-40º to 122ºF).
Relative humidity: 85%, +/ - 5%.
Storage Temperature: -40º to 70ºC (-40º to 158ºF).
Operating Altitude: -304.8 to 2,000m (-1000 to 6.561.7 ft.).
Regulatory
Compliance UL/CUL Listed for Information Technology Equipment (UL 60950-1).
CE approved.
Weights (approx.) Product: 0.2 lbs. (0.1kg), Shipping: 0.25 lbs. (0.11kg).
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.
NetWay112 I29P MEMBER
- 4 - NetWay112
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]