NetWay112 - 1 -
Overview:
Altronix NetWay112 is a single port PoE injector which provides power and passes data (e.g. video) for
PoE compliant devices. Devices may be located up to 100m from NetWay112. To extend data distance
for an additional 100m use NetWayXT/NetWayXTX repeater modules.
Features:
Rev. 100614
Installation Guide
NetWay112
Single Port PoE Injector for Standard NetWork Infrastructure
Agency Listings:
• UL/CUL Listed for Information Technology
Equipment (UL 60950-1).
• CE approved.
Input:
• 12VDC/1.5A to 16VDC/1.1A.
Data:
• One (1) PoE port provides power and passes
data over ethernet (CAT5) cable up to 100m.
• Data rate: 10/100 Base-T compliant.
PoE:
• IEEE 802.3af (15W) compliant.
Features:
• Port status LED.
• PoE manual shutdown feature allows for
cameras and/or edge devices to be reset.
For UL 60950-1 applications only
(see Technical Specifications table pg. 4).
• Auto detection and protection of legacy
non-PoE cameras/devices.
• Data rate: 10/100 BASE-T compliant.
• Compact insulated housing.
• Spring terminals (Input and PoE shutdown).
Dimensions (W x L x H approx.):
2.5” x 3.8” x 1”
(63.5mm x 96.52mm x 25.4mm).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all
local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire
suitable for the application.
Unit is intended to be used with a UL Listed Class 2 or LPS (limited power supply). NetWay112 is
not intended to be connected to outside plant leads and should be installed indoors within the protected
premises. NetWay112 is intended for indoor use only.
1. Mount NetWay112 in desired location utilizing the mounting hole (Fig. 1a, pg. 2).
Use a proper fastener and/or wall anchor when securing NetWay112 with screw through its
mounting hole to the wall.
2. Connect UL Listed Class 2 or LPS (limited power supply) providing 12VDC/1.5A to 16VDC/1.1A
to terminals marked [+ DC --- Input], carefully observing polarity (Fig. 1b, pg. 2).
Use 22AWG - 16AWG wire for this connection.
Input power should be a Access Control power supply or a transformer.
3. Connect structured cable from port marked [IN] on NetWay112 to the corresponding input of an
UL Listed ethernet switch or video server (Fig. 1b, pg. 2).
4. Connect structured cable from port marked [OUT] on the NetWay112 to the PoE device (Fig. 1b, pg. 2).
5. Port status LED will illuminate indicating normal operation (Fig. 1c, pg. 2).
6. To initiate PoE shutdown connect 12VAC to 24VAC or 5VDC to 24VDC to the input terminals marked
[Power Shutdown] on the NetWay112 (Fig. 1b, pg. 2). The PoE output voltage may be shut down by
manually applying voltage in the rated range (PoE Shutdown Voltage Range in Specifications). Upon
applying voltage, the output will drop to zero volts. Removal of voltage from the shutdown terminals
or applying zero volts to the shutdown terminals will allow the PoE output to operate normally to
supply power to PoE compliant devices.
Note: Return to normal operation from shutdown can take about 4 seconds. Although there is no
output voltage to power PoE devices during shutdown, data signals may still be present on the data
pair lines of the CAT5 cable.
Installing a NetWay1512 adapter for 12VDC IP cameras up to 13W:
1. Mount NetWay1512 in the proximity of IP camera (Fig. 3, pg. 3). Use velcro (supplied).
2. Connect structured cable from port marked [IN] on NetWay1512 to port marked [OUT] of
NetWay112 (Fig. 3, pg. 3, Fig. 1b pg. 2).
3. Connect structured cable from port marked [OUT] on NetWay1512 to the IP camera/device
(Fig. 3, pg. 3, Fig. 1b pg. 2).
4. Connect 12VDC output from NetWay1512 terminals marked [+ 12VDC --- ] to the power input of
the IP camera (Fig. 3, pg. 3). Polarity must be observed.
5. Power LED indicator will illuminate on NetWay1512 under normal conditions (Fig. 3, pg. 3).
