Altronix TROVE T2SK78DV User manual

T2SK78DV
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with
TSH2 Altronix/Software House backplane
- One (1) AL1024XB2V - Power Supply/Charger
- One (1) ACM8CB - PTC Protected Access Power Controller
- One (1) VR6 - Voltage Regulator
- One (1) PDS8CB - Dual Input Power Distribution Module
- One (1) Rocker Switch Bracket with One (1) Rocker Switch
T3SK758DV
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove3 enclosure with
TSH3 Altronix/Software House backplane
- One (1) AL1024XB2V - Power Supply/Charger
- One (1) AL1012XB220 - Power Supply/Charger
- One (1) ACM8CB - PTC Protected Access Power Controller
- One (1) PD8ULCB - PTC Protected Power Distribution Module
- One (1) Rocker Switch Bracket with Two (2) Rocker Switches
T3SK7516DV
16 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove3 enclosure with
TSH3 Altronix/Software House backplane
- One (1) AL1024XB2V - Power Supply/Charger
- One (1) AL1012XB220 - Power Supply/Charger
- Two (2) ACM8CB - PTC Protected Access Power Controllers
- One (1) PD8ULCB - PTC Protected Power Distribution Module
- One (1) Rocker Switch Bracket with Two (2) Rocker Switches
Altronix/Software House Kits
Models Include:
Rev. TSKLDV012623
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide
Access & Power Integration

- 2 - Trove Software House XBV PTC Kits Installation Guide
Overview:
Altronix Trove Software House kits are pre-assembled and consist of Trove enclosure with factory installed Altronix power supply/chargers and
sub-assemblies. These kits also accommodate various combinations of Software House boards for up to sixteen (16) doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
220VAC
60Hz
Input
Current
(A)
Power
Supply
Board
Input
Fuse
Rating
Power
Supply
Board
Battery
Fuse
Rating
Nominal DC Output
Voltage Options
Maximum
Supply Current
for Main Output
on Power Supply
board and
ACM8CB
Access Power
Controller’s
outputs (A)
Fail-
Safe/
Fail-
Secure
Outputs
Current Per ACM8CB Output (A) ACM8CB Board Input Fuse Rating ACM8CB Board Output PTC Rating PDS8CB Board Input PTC Rating PDS8CB Board Output PTC Rating PD8ULCB Board Output PTC Rating
Power
Supply 1
Power
Supply 2
24VDC
Output
Range
(V)
12VDC
Output
Range
(V)
T2SK78DV 2.5 5A/
250V
15A/
32V 20.17-26.4 – 24VDC @ 9.2A 8 2.0 10A/
250V 2.5A 9A 2.5A –
T3SK758DV 3.8 5A/
250V
15A/
32V 20.19-26.4 10.0-13.2 24VDC @ 9.2A 8 2.0 10A/
250V 2.5A – – 2.5A
T3SK7516DV 3.8 5A/
250V
15A/
32V 20.19-26.4 10.0-13.2 24VDC @ 9.2A 16 2.0 10A/
250V 2.5A – – 2.5A
Hardware and Accessories:
• Tamper switch (Altronix Model TS112 or equivalent) - one (1) for T2SK78D, two (2) for T3SK758D or T3SK7516D.
• Cam lock.
• Battery leads.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1.Remove backplane from enclosure. Do not discard hardware.
2.Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install
the three fasteners. Place the enclosure’s upper keyholes over the three upper screws.
Install the three lower screws and make sure to tighten all screws.
3.Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location,
opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2”
from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or
the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.
4.Mount Software House boards to backplane, refer to pages 3-5.
5.Refer to the XBV Power Supply/Charger Installation Guide for AL1012XB220 and AL1024XB2V
and corresponding Sub-Assembly Installation Guides for the following models: PD8ULCB, ACM8CB,
PDS8CB, VR6 for further installation instructions.
Metal or Nylon Spacer | 5/16” Pan Head Screw | Lock Nut
Fig. 1
Tamper Switch
(included)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure

Trove Software House XBV PTC Kits Installation Guide - 3 -
Software House I8, R8 or I8-CSI Module
Software House
iSTAR Ultra GCM
Software House iSTAR Ultra ACM SE
USB PORT
USB Port
Software House iStar Ultra ACM
RSB1
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GND IN GND IN GND IN GNDIN GND IN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
+ INP1 --
PWR1 +OFF
IN1
IN2
Out1
<1 off 2>
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
Altronix VR6 is mounted under PDS8CB
Altronix - PDS8CB
L
G
N
BAT FAIL
AC FAIL
NC
C
NO NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 2a
T2SK78DV: Configuration of Software House iSTAR Ultra ACM or ACM SE Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with corresponding pems.
2. Fasten spacers (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, iSTAR Ultra ACM SE
and/or I8, R8, I8-CSI boards (Fig. 2, 2a, pg. 3).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 2a, pg. 3).
Note: Software House iSTAR Ultra ACM and iSTAR Ultra ACM SE boards have one (1) USB port each.
Please orient the board in the appropriate position according to the Fig. 2 below.
4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).
Fig. 2
Altronix AL1024XB2V

- 4 - Trove Software House XBV PTC Kits Installation Guide
T3SK758DV: Configuration of Software House iSTAR Ultra ACM Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with pems provided.
2. Fasten spacers (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, and/or I8, R8, I8-CSI
boards (Fig. 3, 3a, pg. 4).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 3a, pg. 4).
Note: Software House iSTAR Ultra ACM boards have one (1) USB port each.
Please orient the board in the appropriate position according to the Fig. 3 below.
4. Fasten backplane to Trove3 enclosure utilizing lock nuts (provided).
Fig. 3
Altronix - PD8ULCB
RSB2
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GNDIN GND IN GND IN GNDIN GNDIN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
INPUT
COMMON POWER OUTPUTS N P
N
P
FUSED POWER OUTPUTS
L
G
N
BAT FAIL
AC FAIL
NC
C
NO NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
+ BAT -
L G N BAT FAIL NC C NO NC C NO AC FAIL
AC DC
- DC +
Altronix - AL1012ULXB
Software House
iSTAR Ultra GCM
Software House iSTAR Ultra ACM
USB PORT
USB PORT
Software House
I8, R8 or I8-CSI
Module
Software House
I8, R8 or I8-CSI
Module
Software House iSTAR Ultra ACM SE
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 3a
Altronix AL1024XB2V
Altronix AL1012XB220

Trove Software House XBV PTC Kits Installation Guide - 5 -
T3SK7516DV: Configuration of Software House iSTAR Ultra ACM Boards
1. Align the Software House boards on the backplane to match the boards’ mounting holes with pems provided.
2. Fasten spacers (provided) to pems that match the hole pattern for Software House iSTAR Ultra GCM, iSTAR Ultra ACM, and/or I8, R8, I8-CSI
boards (Fig. 4, 4a, pg. 5).
3. Mount Software House boards to spacers utilizing provided 5/16” pan head screws (Fig. 4a, pg. 5).
Note: Software House iSTAR Ultra ACM boards have one (1) USB port each.
Please orient the board in the appropriate position according to the Fig. 4 below.
4. Fasten backplane to Trove3 enclosure utilizing lock nuts (provided).
Fig. 4
Altronix - PD8ULCB
RSB2
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GNDIN GND IN GND IN GNDIN GNDIN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 OUTPUT 7 OUTPUT 8
NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM NC C NO COM
IN GNDIN GND IN GND IN GNDIN GNDIN GND IN GND IN GND
1 2 3 4 5 6 7 8
INPUT
TRIGGER
10A 250V
+INP- T + RET-
NO C NC
FACP INTERFACE
Power Control
- + - +
F1 F2 F3 F4 F5 F6 F7 F8
MAIN
TRG
FACP
1 2 3 4
1 2 3 4
ON
ON
1 2 3 4
1 2 3 4
ON
ON
Altronix - ACM8CB
INPUT
COMMON POWER OUTPUTS N P
N
P
FUSED POWER OUTPUTS
L
G
N
BAT FAIL
AC FAIL
NC
C
NO NC
C
NO
AC
DC
- BAT + + DC -
AC DELAY
Altronix - AL1024ULXB2
+ BAT -
L G N BAT FAIL NC C NO NC C NO AC FAIL
AC DC
- DC +
Altronix - AL1012ULXB
Software House
iSTAR Ultra GCM
Software House iSTAR Ultra ACM
USB PORT
USB PORT
Software House
I8, R8 or I8-CSI
Module
Software House
I8, R8 or I8-CSI
Module
Software House iSTAR Ultra ACM SE
Software House iSTAR Ultra ACM
USB PORT
USB PORT
Software House iSTAR Ultra ACM SE
Pem
Spacer
Power Supply or
Sub-Assembly Backplane
Pan Head
Screw
Fig. 4a
Altronix AL1024XB2V
Altronix AL1012XB220

- 6 - Trove Software House XBV PTC Kits Installation Guide
Notes:

Trove Software House XBV PTC Kits Installation Guide - 7 -
T2SK78D Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)
6.75” (171.5mm)8.25” (209.5mm)
8.00” (203.2mm)
2.00” (50.8mm)
2.00” (50.8mm)
1.25” (31.8mm)
1.25” (31.8mm)
5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)
1.25” (31.8mm)
6.25” (158.8mm) 19.80” (502.9mm)
1.00” (25.4mm)
27” (685.8mm)
1.5”
(38.1mm)
2.00” (50.8mm) 2.00” (50.8mm)
3.5”(88.9mm) 3.5”(88.9mm)
21.50” (546.1mm)
5.25” (133.35mm) 5.25” (133.35mm)
6.25” (158.8mm)
1.25”
(31.8mm)
0.85” (21.6mm)
0.5625” (14.3mm)
2.415” (61.3mm)
0.685” (17.4mm)
1.77”
(45mm)
0.885” (22.5mm)
1.125” (28.3mm)
Knockouts
2.00” (50.8mm) 2.00” (50.8mm)

- 8 - Trove Software House XBV PTC Kits Installation Guide
T3SK758D and T3SK7516D Enclosure Dimensions (H x W x D approximate):
36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)
G
G
2”
(50.8mm)
8.75” (222.3mm) 8.75” (222.3mm)
8.62” (219mm)
7.06” (179.3mm)
1.25” (31.8mm)
1.25” (31.8mm)
2.00” (50.8mm) 7.12” (222.3mm) 9.5” (241.3mm) 9.5” (241.3mm)
30.12” (768.1mm)
14.01” (355.9mm) 14.01” (355.9mm)
1.25” (31.8mm) 1.55” (39.4mm)
1.78” (45.2mm)
1.25” (31.8mm)
1.07”
(27.2mm)
1.10” (27.9mm)
2” (50.8mm)
10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)
2.00” (50.8mm)10.75” (273.1mm)10.75” (273.1mm) 10.62” (269.8mm)
36.12” (917.5mm) 33.63” (854.2mm)
2” Conduit
3/4” Conduit
1” Conduit
3/4” Conduit
1” Conduit
1.5” Conduit
1.25” Conduit 1.5” Conduit
1.25” Conduit
3/4” Conduit
1” Conduit
3/4” Conduit
1” Conduit
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IITroveSH XBV Kit D Series G25V MEMBER