Altronix Trove T1SPK34 User manual

T1SPK34
4 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove1 enclosure with TSP1 Altronix/Suprema backplane
- One (1) AL600ULXB - Power Supply/Charger
- One (1) ACM4 - Fused Access Power Controller
- One (1) VR6 - Voltage Regulator
- One (1) PDS8 - Dual Input Fused Power Distribution Module
Rev. 020922
Installing Company: _________________________ Service Rep. Name: __________________________________________
Address: _________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide
All components of this Trove kit are UL Listed sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.
Access & Power Integration

- 2 - T1SPK34 Installation Guide
Overview:
Altronix T1SPK34 Trove Suprema kit is pre-assembled and consists of Trove1SP1 enclosure/backplane with factory installed Altronix power supply/
charger and sub-assemblies. T1SPK34 kit also accommodates one (1) Suprema CoreStation module for up to four (4) doors in a single enclosure.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the
wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure. Mark the position
of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes
over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent)
in desired location, opposite hinge. Slide the tamper switch bracket onto the edge
of the enclosure, approximately 2” from the right side (Fig. 1, pg. 2).
Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device. To activate alarm signal
open the door of the enclosure.
4. Mount Suprema CoreStation module to TSP1 backplane, refer to page 3.
5. Refer to the ULXB Power Supply/Charger Installation Guide for AL600ULXB
and corresponding Sub-Assembly Installation Guides for the following models:
ACM4, PDS8 and VR6 for further installation instructions.
Hardware:
Nylon Spacer | 5/16” Pan Head Screw | Lock Nut
Fig. 1
Tamper Switch
(included)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure

T1SPK34 Installation Guide - 3 -
Configuration of Suprema CoreStation module:
1. Fasten spacers (provided) to pems that match the hole pattern for Suprema CoreStation module (Fig. 2, pg. 3).
2. Mount module to spacers utilizing 5/16” pan head screws (provided) (Fig. 2, 2a, pg. 3).
Note: Suprema CoreStation modules have one (1) RJ45 jack each.
Please make sure that it is mounted correctly, as shown in Fig. 2 below.
4. Fasten TSP1 backplane to Trove1 enclosure utilizing hardware (provided).
Fig. 2
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
Common Power Outputs (NEG)
P
N
+ INP1 - + INP2 -
PWR1+
PWR2+
COM(-)
PWR2+
COM(-)
P
N
Fuse1 Fuse2 Fuse3 Fuse4 Fuse5 Fuse6 Fuse7 Fuse8
IN1 Fuse
IN2 Fuse
PWR1+ Dual Voltage
Power Distribution
Module
PDS8
1 2 3 4 5 6 7 8
TRG
TRIGGER
INPUT
ACM4
ACCESS POWER
CONTROLLER
LED1 LED2 LED3 LED4
MAIN
OUTPUT 1
NC C NO COM NC C NO COM NC C NO COM NC C NO COM
OUTPUT 2 OUTPUT 3
IN GND
1
IN GND
2
IN GND
3
IN GND
4
OUTPUT 4
-- +
CONTROL
-- +
POWER
+INP- T +RET-
INTERFACE
NO C NC
FACP
Altronix PDS8
with VR6 below
BAT FAIL NC C NO NC C NO AC FAIL
AC DC BAT
+BAT- + DC -
L G N
OFF - 24V
ON - 12V
ON
Altronix
AL600ULXB
Altronix ACM4
5
Suprema
CoreStation
RJ45
Pem
Spacer
Suprema CoreStation
module Backplane
Pan Head
Screw
Fig. 2a

- 4 - T1SPK34 Installation Guide
Trove1 Enclosure Dimensions (H x W x D approximate):
18” x 14.5” x 4.625” (457mm x 368mm x 118mm)
4.5” (114.3mm) 4.5” (114.3mm) 2.75”
(69.9mm)
1.115” (28.3mm)
1.36” (34.5mm)
1.25” (31.8mm) 1.25” (31.8mm)
1.5” (38.1mm)
8.5” (215.9mm)6.5” (165.1mm)
1.5” (38.1mm)
8.5” (215.9mm)6.5” (165.1mm)
4.5” (114.3mm)
13.0” (330.2mm)
0.6” (15.2mm)
14.5” (321.3mm)
1.45” (36.8mm)
7.25” (184.2mm)
1.95” (49.5mm)
1.1” (27.9mm)
0.6” (15.2mm)
0.57” (14.5mm)
18.0” (457.2mm)
1.25” (31.8mm)
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIT1SPK34 B09V
MEMBER