Altronix ALTV1224C User manual

Overview:
The Altronix ALTV1224C AC/DC Dual Output Power Supply is designed to provide both 12VDC and 24VAC out-
puts where a combination of both AC and DC outputs are required. It will provide eight (8) 3.5 amps 12VDC out-
puts and eight (8) 3.5 amps 24 VAC outputs.
Specifications:
• 115 VAC 50 / 60 HZ, 1.45 amps.
• 7 amps total continuous output current.
• 3.5 amps continuous supply current at
24VAC output.
• 3.5 amps continuous supply current at 12VDC.
• 16 individually fused outputs.
(8 outputs @ 12VDC and 8 outputs@ 24VAC)
(Fig. 1).
• Main fuses are rated at 5 amps / 250VAC
(Fig. 1).
• AC /DC power LED indicator.
• Surge protection.
• Spare fuses included.
• Unit maintains camera synchronization.
• Power ON/OFF switch.
• Ease of installation saves time and eliminates
costly labor.
Enclosure dimensions: 15.5"H x 12"W x 4.5"D
Optional available with 220VAC input order
model # ALTV1224C/220.
Installation Instructions:
1. Mount ALTV1224C enclosure in desired
location.
2. Slide switch SW1 (Fig. 1) to OFF position.
3. Connect the AC (115 VAC 50 / 60 Hz) to the two black and white flying leads of the transformers (Fig 1).
4. Connect devices to output terminals using the following procedure (Fig. 1).
Connect each DC device to terminal pairs on DC output board 1 thru 8, marked [P (+) and N (-)] carefully
observing correct polarity.
Connect each AC device to terminal pairs on AC output board 1 thru 8, marked [P (+) and N (-)].
Note: Is good operating practice to measure output voltage before connecting devices.
5. When batteries are being used the DC output voltage must be adjusted by turning the trim pot VR1 (Fig 1)
clockwise to increase the output voltage to 13.7 VDC. Connect battery to terminals marked [- BAT +] (Fig. 1)
on the unit (battery leads included).
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting
the output voltage. When the battery charging voltage is increased the DC output voltage will also increase.
6. Slide switch SW1 (Fig. 1) to ON position.
7. Green LED on the PD8’s will illuminate when power is present.
8. Upon completion of wiring, secure enclosure door with screws (supplied).
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should
be made by qualified service personnel and should conform to all local codes and in accordance with the
national electrical code.
ALTV1224C
AC/DC Dual Output Power Supply
XFMR
PD8
F1 F2 F3 F4 F5 F6 F7 F8
SPARE
MAIN
FUSE
FUSED POWER OUTPUTS
JMP1
12345678 LED
SW1
COMMON POWER OUTPUTS
MOV
ON OFF
P
N
+ DC INPUT -
- BAT +
AC AC
SMP5PM
SUPERVISED POWER SUPPLY / CHARGER
DC
AC
1234
ON
PD8
F1 F2 F3 F4 F5 F6 F7 F8
SPARE
MAIN
FUSE
FUSED POWER OUTPUTS
JMP1
12345678 LED
SW1
COMMON POWER OUTPUTS
MOV
ON OFF
P
N
AC Outputs
DC Outputs
Black
Lead White
Lead
120 VAC,
60 Hz Input,
1.45 A
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
Fig. 1

Terminal Identification:
SMP5
Terminal Legend Function/Description
AC/ AC Low voltage AC input (24VAC / 175VA).
Altronix part # T24175
+ DC - 12VDC 3.5 amps total continuous output.
- BAT + Stand-by battery connections. Maximum charge rate .5 amp.
PD8 (DC output)
1P - 8P Positive DC power outputs.
1N - 8N Negative DC power outputs.
PD8 (AC output)
1P - 8P AC power outputs.
1N - 8N AC power outputs.
Altronix Corp.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIALTV1224C-Rev. 061699
MEMBER
.875"
1"
1.3"
9.97"
13.53"
2"
2.25" 3.68" 4.56"
1.22"
1.22"
3.25"
1"
13.25"
2"
1.22"
12"
15.5"
8"
4.5"
2.25" 3.68" 4.56"
1.22"
1.25"
2.2"
1"
Enclosure dimensions:
15.5"H x 12"W x 4.5"D