Altronix ALTV129-DC User manual

Overview:
The Altronix ALTV129-DC DC CCTV Power Supply is designed with eight (8) individually fused outputs for
powering CCTV Cameras and other video accessories. It will provide 9 or 12 VDC distributed via eight (8) fuse
output with a total of 4 AMPS continuous supply current.
Specifications:
• Input 115VAC 60Hz, 1.45 amps
• Eight (8) individually fused outputs
• 4 amps continuous supply current
• Output fuses are rated at 3.5 amps / 250VAC
(see Fig.1,#4)
• Main fuses are rated at 5 AMP / 250VAC.
(see Fig. 1, #5)
• Switch selectable 12VDC or 24VDC output
• Filtered and electronically regulated outputs
• AC input and DC output LED indicator
• Power ON/OFF switch
• Surge protection
• Spare fuses included
• Ease of installation saves time and eliminates costly labor
• Unit maintains camera synchronization
• Unit is supplied assembled in enclosure
Enclosure dimensions: 15.5"H x 12"W x 4.5"D
Optional available with 220VAC input
order model # ALTV129-DC/220.
Power Supply Output Specifications:
Output Switch Maximum
VDC Position Load DC
9VDC SW1 Open 4 amps
12VDC SW1 Closed 4 amps
Installation Instructions:
1. Mount ALTV129-DC enclosure in desired locations.
2. Slide switch SW1 (see Fig. 1, #1) to OFF position.
3. Set the ALTV1224-DC to desired DC output voltage by setting switch (SW1) (see Fig 1, #7) on the power supply
board to the appropriate position (see power supply output specification table).
4. Connect the AC (115 VAC 50 / 60 Hz) to the black and white flying leads of the transformer (see Fig 1, #2).
5. Connect each DC device to terminal pairs 1 to 8, marked “1P-1N thru 8P - 8N” (see Fig 1, #3) carefully
observing correct polarity.
Note: Is good operating practice to measure output voltage before connecting devices.
6. When batteries are being used the DC output voltage must be increased by approximately 15% by turning the
trim pot VR1 (see Fig 1, #8) clockwise. Connect battery to terminals - BAT + (see Fig. 1, #6) as marked on the unit
(battery leads included).
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the
output voltage.
7. Slide switch SW1 (see Fig. 1, #1) to ON position.
8. Green LED will illuminate when AC power is present..
9. Upon completion of wiring, secure enclosure door with screws (supplied).
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be
made by qualified service personnel and should conform to all local codes and in accordance with the National Electrical
Code.
Altronix®
ALTV129-DC
CCTV Camera & Accessory Power Supply
XFMR
Black
Lead
Fig. 1
+ DC OUTPUT -
- BAT +
AC AC
SMP5
POWER SUPPLY / CHARGER
DC
AC
White
Lead
115VAC input
60 Hz,
1.45AMP
Open for 12VDC
Close for 24VDC
PD8
F1 F2 F3 F4 F5 F6 F7 F8
SPARE
MAIN
FUSE
FUSED POWER OUTPUTS
JMP1
12345678 LED
SW1
COMMON POWER OUTPUTS
MOV
ON OFF
P
NNP
7
3
4
6
2
5
1
8
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.

Terminal Identification:
SMP5
Terminal Legend Function/Description
AC/ AC Low voltage AC input (28VAC / 175VA).
Altronix part # T28140.
+ DC - 12 or 24VDC 4 amps total continuous output.
- BAT + Stand-by battery connections. Maximum charge rate .5 amp.
PD8
1P - 8P Positive DC power outputs.
1N - 8N Negative DC power outputs.
Altronix Corp.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIALTV129DC-Rev. 030899
MEMBER
.875"
.99" .99"
1.299"
1.299"
9.97"
13.52"
2.0"
1.22"
2.24" 3.68" 8.24"
1.22" 1.22"
1.22"
2.24" 3.68" 8.24"
1.22"
1.22"
1.22"
3.24"
1.22"
1.22"
2.2"
.98"
.875"
1.25"
2.0"
1.22"