Altronix SMP1012X Series User manual

SMP1012Xseries - 1 -
Overview:
These units will convert a 115VAC 50/60Hz input into a regulated 12VDC output at up to 10 amp continuous supply
current (see specifications).
SMP1012X Series Power Supply Configuration Reference Chart:
Altronix
Model Number
Accessory
Power
Distribution
Module(s)
Number of Outputs Fused Outputs PTC Outputs Output Rating (amp) per Output Supervised 115VAC 50/60Hz Input Current (amp) 12VDC Total Output Current (amp)
SMP10C12X - 1 - - 10 - 1.45 10
SMP10C12XX* - 1 - - 10 - 1.45 10
SMP10PMC12X - 1 - - 10 x 1.45 10
SMP10PMC12XX* - 1 - - 10 x 1.45 10
SMP10PM12P4 PD4 4 - 3.5 x 1.45 10
SMP10PM12P4CB PD4CB 4 - x 2.5 x 1.45 10
SMP10PM12P8 PD8 8 x - 3.5 x 1.45 10
SMP10PM12P8CB PD8CB 8 - x 2.5 x 1.45 10
SMP10PM12P16 PD16W 16 x - 3.5 x 1.45 10
SMP10PM12P16CB PD16WCB 16 - x 2.5 x 1.45 10
*Refer to Enclosure Dimensions on pg.7 for enclosure size.
Specifications:
Installation Instructions:
Wiring methods should be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 6-7).
Secure enclosure to earth ground.
2. Connect AC power to the terminals marked [L & N].
Use 18 AWG or larger for all power connections (Battery, DC output).
3. Measure output voltage before connecting devices. This helps avoiding potential damage.
Battery Backup:
• Built-inchargerforsealedleadacidorgeltypebatteries.
• Maximumchargecurrent0.7amp.
• Filteredandelectronicallyregulatedoutputs.
• Automaticswitchovertostand-bybatterywhen
AC fails (zero voltage drop).
Features:
• ACinputandDCoutputLEDindicators.
Features (cont’d):
• Shortcircuitandthermaloverloadprotection.
• Completewithpowersupply,powerdistributionmodule
(when applicable), enclosure, cam lock & battery leads.
• PowerON/OFFswitch.
Supervised models only:
• ACfailsupervision(form“C”contacts).
• Lowbatterysupervision(form“C”contacts).
SMP1012X Series - Installation Guide

- 2 - SMP1012Xseries
4. Connect devices to be powered: a. For Power Supply Board connect to the terminals marked [– DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N through 4P & 4N] (Fig. 3, pg. 4) 1 to 8 marked [1P & 1N through 8P & 8N] (Fig. 4, pg. 4)
or 1 to 16 marked [1P & 1N through 16P & 16N] (Fig. 5, pg. 4), carefully observing correct polarity.
*Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board. When servicing the unit,
AC mains should be removed.
5. When using stand-by batteries, they must be lead acid or gel type. Connect battery to the terminals marked [– BAT +]
(battery leads included). Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
6. Connect appropriate signaling notification devices to the AC Fail & Low Bat supervisory relay outputs
marked [NC, C, NO] (Fig. 1a, below).
Power Supply
Board
LG N
OFF ON
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT + --- DC +
AC DC
5A 250V
15A
Power
Distribution
Module(s)
Earth
Ground
Wire
Strap
(from
Enclosure
to Door)
115 power
mains
INPUT
Divider
LOW BAT
NC C NO NC C NO
AC FAIL
CAUTION: De-energize unit prior to servicing. For continued protection
against fire hazard replace fuse with the same type and rating, 15A, 32V.
12VDC Rechargeable Battery
(optional)
CAUTION: Optional rechargeable stand-by batteries must match the power supply
output voltage setting.
Keep power-limited wiring separate from non power-limited. Use minimum 0.25" spacing.
Fig. 1
Fig. 1a

SMP1012Xseries - 3 -
Earth Ground
Wire Strap
(from
Enclosure
to Door)
115 power mains
CAUTION: De-energize unit prior to servicing. For continued protection
against fire hazard replace fuse with the same type and rating, 15A, 32V.
Power Supply
Board
LG N
OFF ON
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT + --- DC +
AC DC
5A 250V
15A
12VDC Rechargeable Battery
(optional)
CAUTION: Optional rechargeable stand-by batteries must match the power supply
output voltage setting.
Keep power-limited wiring separate from non power-limited. Use minimum 0.25" spacing.
Fig. 2

- 4 - SMP1012Xseries
INPUT
LED
PD4
POWER DISTRIBUTING UNIT
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
F1
F1 F2 F3 F4
COMMON POWER OUTPUTS
1P 1N 2P 2N 3P 3N 4P 4N
DC Output to devices From Power Supply
Board
(Factory Installed)
Used
on PTC
Models
PD8
N
COMMON POWER OUTPUTS
P
FUSED POWER OUTPUTS
1 2 3 4 5 6 7 8
1
D1
INPUT
R1 LED
DC Output to devices From Power Supply
Board
(Factory Installed)
Used
on PTC
Models
Fig. 3 Fig. 4
Power Distribution Module(s):
LED Diagnostics:
Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF Loss of AC, Stand-by battery supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module
Green Power Distribution Module Status.
ON Normal operating condition.
3.5A 250V
For continuous protection against
risk of fire replace fuses with
same type and rating.
common
outputs
protected
outputs
P
N
NPS
XFMR Input
12345678
9 10 11 12 13 14 15 16
NP
DC Output to devices
1P-16P Power Outputs,
1N-16N Common Outputs
) )
From Power
Supply
Board
(Factory
Installed)
1
Used
on PTC
Models
Fig. 5

SMP1012Xseries - 5 -
Terminal Identification:
Power Supply Board
Terminal Legend Function/Description
L, G, N Connect 115VAC to these terminals: L to Hot, N to Neutral.
– DC + 12VDC @ 10 amp continuous outputs.
*AC FAIL
NC, C, NO
Indicates loss of AC power, e.g. connect to audible device or alarm panel. Relay normally energized
when AC power is present. Contact rating 1 amp @ 120VAC / 28VDC
*Low Battery NC,
C, NO
Indicates low battery condition, e.g. connect to alarm panel. Relay normally energized when DC
power is present. Contact rating 1 amp @ 120VAC / 28VDC Low battery threshold: 12VDC output
threshold set @ approximately 10.5VDC
– BAT + Stand-by battery connections. Maximum charge rate 0.7 amp.
*Note: Supervised Models Only.
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module
Terminal Legend Function/ Description
PD4/PD4CB PD8/PD8CB PD16W/PD16WCB
1P to 4P 1P to 8P 1P to16P Positive DC power outputs.

- 6 - SMP1012Xseries
Enclosure Dimensions for:
SMP10C12X SMP10PMC12X
SMP10PM12P4 SMP10PM12P4CB
SMP10PM12P8 SMP10PM12P8CB
SMP10PM12P16 SMP10PM12P16CB
13.5”x13”x3.25”(342.9mmx330.2mmx82.55mm)
1.40”
(36mm)
1.40”
(36mm)
4.85”
(123mm)
4.85”
(123mm)
1.40”
(36mm)
1.40”
(36mm)
5.10”
(130mm)
5.10”
(130mm)
13.0”
(330mm)
5.10”
(130mm)
6.5625”
(167mm)
1.20”
(31mm)
1.20”
(31mm) 1.20”
(31mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
1.0”
(25mm)
1.0”
(
25mm
)
10.5”
(
267mm
)
1.0”
(
25mm
)
1.0”
(25mm)
0.75”
(19mm)
0.75”
(19mm)
0.9375”
(24mm)
0.9375”
(24mm)
11.0”
(279mm)
12.5”
(318mm)

SMP1012Xseries - 7 -
Enclosure Dimensions for:
SMP10C12XX
SMP10PMC12XX
15.5”x12”x4.5”(393.7mmx304.8mmx114.3mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
5.0”
(127.0mm)
5.0”
(127.0mm)
1.5”
(38.1mm)
2.0”
(50.8mm)
2.0”
(50.8mm)
1.75”
(44.45mm)
1.75”
(44.45mm)
4.5”
(114.3mm)
1.25”
(31.75mm)
4.5”
(114.3mm) 1.25”
(31.75mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.1”
(27.94mm)
1.1”
(27.94mm)
0.79”
(20.06mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
0.91”
(23.114mm)
1.375”
(34.925mm)
1.125”
(28.575mm)
15.5”
(393.7mm)
4.615”
(117.22mm)
12.23”
(310.64mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)

- 8 - SMP1012Xseries
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
web site: www.altronix.com, e-mail: [email protected], Made in U.S.A.
IISMP1012X Series - Rev. 051105 H06M MEMBER
Notes: