Altronix HubWay ld User manual
Rev. 030408
Active UTP Transceiver Hub
with Integral Isolated Camera Power
Installation Guide
Models Include:
HubWayLD8Di HubWayLD16Di
- UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP
Transceiver Hub with Integral Isolated Camera Power Transceiver Hub with Integral Isolated Camera Power
HubWayLD82Di HubWayLD162Di
- UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP
Transceiver Hub with Integral Isolated Camera Power Transceiver Hub with Integral Isolated Camera Power
- Includes eight (8) UL Listed Accessory - Includes sixteen (16) UL Listed Accessory
HubWayAv Video Balun/Combiners HubWayAv Video Balun/Combiners
HubWayLD83Di HubWayLD163Di
- UL Listed eight (8) Channel Active UTP - UL Listed sixteen (16) Channel Active UTP
Transceiver Hub with Integral Isolated Camera Power Transceiver Hub with Integral Isolated Camera Power
- Includes eight (8) UL Listed Accessory - Includes sixteen (16) UL Listed Accessory
HubWayDv Video Balun/Combiners HubWayDv Video Balun/Combiners
More than just power.TM
Video • Data • Power
- 2 - HubWayLD Active Isolated Unit
Overview:
Altronix HubWayLD8Di/16Di Active UTP Transceiver Hub w/Integral Isolated Camera Power transmits UTP video,
RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 8 or 16 camera channels in
a space saving 1U EIA 19” rack mount chassis which may be rack, wall or shelf mounted. Video transmission range is
up to 3000 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix
HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners. In addition, the unit features individu-
ally selectable 24VAC or 28VAC PTC protected outputs with surge suppression. An optional HubSat4D Passive UTP
Transceiver Hub with Integral Camera Power can be used as an accessory module to transmit video from up to 4 cameras
over a single CAT-5 or higher structured cable back to the HubWayLD8Di/16Di. In addition, the HubSat4D provides
power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs.
WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
Installation Instructions:
1. Set the input voltage selector switch located on the left side of the HubWayLD8Di/LD16Di unit (facing front panel)
for 115VAC or 230VAC operation (Fig. 1k, pg. 4).
2. Attach mounting brackets to HubWayLDi unit for rack or wall mount installation (Figs. 6-7, pg. 8). Affix rubber pads
to HubWayLD for shelf installation (Fig. 8, pg. 8).
HubWayLD Specifications:
HubWayLD82Di
• HubWayLD8Di with eight (8) UL Listed Accessory
HubWayAv Video Balun/Combiners for 24VAC Cameras.
HubWayLD83Di
• HubWayLD8Di with eight (8) UL Listed Accessory
HubWayDv Video Balun/Combiners for 12VDC Cameras.
HubWayLD162Di
• HubWayLD16Di with sixteen (16) UL Listed Accessory
HubWayAv Video Balun/Combiners for 24VAC Cameras.
HubWayLD163Di
• HubWayLD16Di with sixteen (16) UL Listed Accessory
HubWayDv Video Balun/Combiners for 12VDC Cameras.
Agency Listings:
• ULListedforCommercialCCTVEquipment(UL2044).
CUL Listed - CSA Standard C22.2 No.1-04, Audio,
VideoandSimilarEquipment.
Data:
• RS422/RS485datainputs.
Power:
• Individuallyselectable24VACor28VACpoweroutputs
with OFF position.
• IndividualelectronicallyisolatedPTCoutputs.
• PTCsarerated@1ampperchannel.
• Surgesuppression.
Visual Indicators:
•ACinputpowerindicator.
•VideosignalandpowerLEDindicators.
Features:
• PictureandGaincontrol.
• Illuminatedmasterpowerdisconnectcircuitbreaker
with manual reset.
• IEC320-3-wiregroundedlinecord(detachable).
• Unitcanberack,wallorshelfmounted.
• 1UrackmountchassisforuseinstandardEIA19”rack.
Accessories:
• VideoBalun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayAv2 - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
- HubWayDvi - for use with non-isolated 12VDC cameras.
• OptionalHubSat4Dallowstransmissionofupto
four (4) video signals over a single CAT-5 or higher
structured cable.
HubWayLD8Di/LD82Di/LD83Di
Input:
• 115VAC60Hz,2.5ampor
230VAC 50/60Hz, 1.5 amp.
Video:
• Eight(8)channelsofvideoovertwistedpairupto
a distance of 3000 ft. per channel.
• Eight(8)75ohmvideooutputs.
Power:
• Unitprovidesupto1ampmax.perchannelnotto
exceed a total of 8 amp (150VA) maximum current.
HubWayLD16Di/LD162Di/LD163Di
Input:
• 115VAC60Hz,5ampor
230VAC 50/60Hz, 2.5 amp.
Video:
• Sixteen(16)channelsofvideoovertwistedpairupto
a distance of 3000 ft. per channel.
• Sixteen(16)75ohmvideooutputs.
Power:
• Unitprovidesupto1ampmax.perchannelnotto
exceed a total of 16 amp (300VA) maximum current.
Common Specifications:
Additional Models:
HubWayLD Active Isolated Unit - 3 -
3. Secure the unit in a rack, mount unit to a wall or place unit on a shelf as desired (unit should be spaced at least 3”
from any video monitors).
4. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5, pg. 7).
5. Plug the grounded AC line cord (included) into the IEC 320 connector of the HubWayLD8Di/HubWayLD16Di
unit (Fig. 1j, pg. 4). Insert the plug end of the line cord into a grounded AC receptacle.
6. Set voltage output selector switch of each camera channel for 24VAC or 28VAC (Fig. 1d, pg. 4).
7. ConnecttheBNCvideooutputsforHubWayLD8Di/LD16DiChannels1-8(Channels1-16)tothe
correspondingvideoinputsontheheadendequipment(DVR)(Fig. 1f, pg. 4).
8. ConnecttheRS422/RS485outputoftheheadendequipment(DVR)totheone(1)orbothdatainputterminal
blocks of the HubWayLD8Di or HubWayLD16Di unit (polarity must be observed) (Fig. 1e, pg. 4).
Note: The Data input terminals of the HubWayLD8Di or HubWayLD16Di must be wired in parallel for proper
operation. When using fixed cameras disregard this step.
9. Connect Video Balun/Combiner at camera 1 to the HubWayLD8Di or HubWayLD16Di unit utilizing CAT-5 or
higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked
[Channel 1] of the HubWayLD8Di/LD16Di (Fig. 1a, pg. 4). Plug the RJ45 connector at the opposite end of the
structured cable into the RJ45 jack of the Video Balun/Combiner located at camera 1.
• For24VACcamerasuseAltronixmodelHubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e, pg. 5).
• For12VDCcamerasuseAltronixmodelHubWayDvVideoBalun/Combiner(Figs. 2c, 2d, pg. 5).
• Fornon-isolated12VDCcamerasuseAltronixmodelHubWayDviVideoBalun/Combiner(Figs. 2c, 2d, pg. 5).
Repeat steps 6-9 for each additional camera (Channels 2-8 or Channels 2-16).
Note: When a particular camera exceeds the maximum distance for power transmission, a local external power
sourceisrequired.Optionally,anAltronixHubSat4DPassiveUTPTransceiverHubwithIntegralCameraPower
may be utilized (Fig. 4a, pg. 6).
The combined total cable distance must not exceed 3000 ft. for video transmission between the
HubWayLD8Di/LD16Di and each camera routed through the HubSat4D.
10. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5, pg. 7) and measure the
output voltage at the power output of each Video Balun/Combiner (Figs. 2b, 2d, pg. 5) before powering each camera
to ensure proper operation and avoid possible damage.
• HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 5).
• HubWayDv/HubWayDvi-Terminalsmarked[–12VDC+](Figs. 2c, 2d, pg. 5).
11. Set illuminated master power disconnect circuit breaker to the (OFF) position to make the final connections
(Fig. 5, pg. 7).
12. Connect the power outputs of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to
the power inputs of the cameras (Figs. 2a-2e, pg. 5). Polarity must be observed.
13. Connecttheterminalsmarked[+DATA-- ] of the HubWayAv or HubWayDv Video Balun/Combiners to the data
terminals of the cameras for PTZ control (Figs. 2a-2e, pg. 5). Polarity must be observed.
When using fixed cameras disregard this step.
14. Connect the BNC connector of the HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners
to the BNC video outputs of the cameras (Figs. 2a-2e, pg. 5).
15. Upon completion of wiring set illuminated master power disconnect circuit breaker to the RESET (ON) position
(Fig. 5, pg. 7).
16. The power LEDs (Red) located on the front of the HubWayLD8Di/LD16Di will illuminate when AC power
is present (Fig. 1c, pg. 4).
Note: If any of these LEDs are not illuminated either a voltage output selector switch is in the OFF position or the
PTC is tripped for that channel.
ToresetthePTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain
in the OFF position for approximately 2 minutes in order for the PTC to reset.
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for 24VAC or 28VAC (Fig. 1d, pg. 4).
17. ACLED(Green)oftheHubWayAvorDCLED(Red)oftheHubWayDv/HubWayDviVideoBalun/Combiners
will illuminate indicating power is present at the cameras (Fig. 2b, 2d, pg. 5).
18. The video signal indicator LEDs (Red) located on the rear of the HubWayLD8Di /LD16Di will illuminate when
video signal is present (Fig. 1i, pg. 4). If any of these LEDs are not illuminated, no video signal is present for
that corresponding channel.
19. OptimizethepicturequalityforChannels1-8(Channels1-16)byadjustingthecorrespondingpotentiometers
marked [Picture] (Fig. 1g, pg. 4).
20. SetgainforChannels1-8orChannels1-16byadjustingthecorrespondingpotentiometersmarked[Gain]
(Fig. 1h, pg. 4).
- 4 - HubWayLD Active Isolated Unit
1 2 3 4 CH 1-4 CH 5-8
28VAC
OFF
24VAC
+ DATA -
1-8
+ DATA -
9-16
5 6 7 8 9 10 11 12 CH 9-12
28VAC
OFF
24VAC
13 14 15 16 CH 13-16
AC POWER
16
PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTUREGAINPICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN
15 14 13 12 11 10 987654 32 1
OFF
RESET
1a - Channels 1-8 (HubWayLD8i)
or Channels 1-16 (HubWayLD16i):
CAT-5 or higher structured cable to
Video/Balun Combiners at
cameras 1-8 or 1-16. When using an
optional HubSat4D any of the out-
puts can be utilized for the data trans-
mission to PTZ”s.
1f - BNC
Connector: Video
outputs to head end
equipment(DVR).
1d - Output voltage
switches: Selects
24VAC/28VAC/
OFF
for each output.
1b - Channels 1-4, Channels 5-8, Channels 9-12 & Channels 13-16:
CAT-5 or higher structured cable from optional HubSat4D enables
video transmission from up to four (4) cameras.
1i - LED(s) 1-16:
Video signal indicators.
1j - IEC 320 Connector:
115VAC 60Hz/230VAC
50/60Hz (grounded line
cord included).
Fig. 1
1g - Picture:
Adjusts video
quality.
1h - Gain:
Regulates the
output video
and sync levels.
1e - Data: Removable
terminal blocks for RS422/
RS485 input from head end
equipment(DVR)forPTZcontrol.
+ --
Data input from
Head End
Equipment (DVR).
Top View
1k - Input Voltage
Switch: Selects 115VAC
60Hz/230VAC 50/60Hz
(switch is located on the left
side of the unit).
115VAC 220VAC
1c - LED(s) 1-16:
Power indicators.
Front
Rear
HubWayLD Active Isolated Unit - 5 -
HubWayAv, HubWayAv2, HubWayDv, and HubWayDvi Video Balun/Combiners:
Altronix
Model Number
Input Voltage
from HubWay
Unit Output Voltage to Camera Camera Type Power LED
HubWayAv *24VAC/28VAC *24VAC/28VAC *24VAC/28VAC Green
HubWayAv2 *24VAC/28VAC *24VAC/28VAC *24VAC/28VAC N/A
HubWayDv *24VAC/28VAC 12VDC
12VDC cameras
Red
HubWayDvi *24VAC/28VAC 12VDC electronically isolated 12VDC cameras without isolation Red
*Based on camera load and structured cable length.
1 - White/Orange [VIDEO +]
2 - Orange [VIDEO -- ]
3 - White/Green [DATA +]
4 - Blue [AC 1]
5 - White/Blue [AC 2]
6 - Green [DATA -- ]
7 - White/Brown [AC 2]
8 - Brown [AC 1]
Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations
HubWayAv/HubWayAv2 passes AC voltage from pins
4,5,7,8toterminalsmarked[ACPower](Fig. 3, pg. 5).
HubWayDv/HubWayDvi converts AC voltage to DC
voltagefrompins4,5,7,8toterminalsmarked
[--12VDC+](Fig. 3, pg. 5).
VIDEO BALUN/COMBINER
CAT5 + D ATA-- POWER
AC
VIDEO
HubWayAv
VIDEO
AC Power
to Camera
Data to
Camera
--
+
Data to
Camera
Green Power LED
12VDC Power
to Camera
+
--
Red Power LED
Wire
Connectors
RJ45 Jack RJ45 Jack
To BNC
Connector
of Camera
To BNC
Connector
of Camera
Structured
Cable from
HubWay8CD
or
HubWay16CD
Structured
Cable from
HubWay8CD
or
HubWay16CD
VIDEO BALUN/COMBINER
HubWayDv
CAT5 + D ATA-- -- 12VDC+
--
+
Wire
Connectors
* Also Available as:
HubWayDvi
Video Balun/
Combiner
for non-isolated
12VDC cameras
Fig. 2
Fig. 2c
Fig. 2a
Fig. 2b
Fig. 2e
HubWayAv2
Fig. 2d
Video from Camera
Data to Camera
Power to Camera
Cat5
back to
HubWay
or
HubSat
- 6 - HubWayLD Active Isolated Unit
115VAC
Input, 50/60Hz
Video
Power
Video
Data
Power
Video
Power
HubWayDv/Dvi
Video Balun
Combiner
CAT- 5
CAT- 5CAT- 5
Fixed
Camera Fixed
Camera
HubWayAv
Video Balun
Combiner
Data
Video
Head End Equipment (DVR)
RS485
Video (Coax)
Four (4) Video
signals on a
single CAT- 5
Data
(CAT-5)
Power
HubWayDv/Dvi
Video Balun
Combiner
Video
Data
PTZ
Camera
PTZ
Camera
Power
Video
Data
Power
HubWayAv
Video Balun
Combiner
HubWayAv
Video Balun
Combiner
Fixed
Camera
Fixed
Camera
Max.
video
3000 ft.
PTZ
Camera
Video
Power
HubWayDv/Dvi
Video Balun
Combiner
CAT- 5
24VAC/28VAC
Camera Power
Provided
by HubSat4D
Video
Data
Power
Outdoor
NEMA
Rated
Power
Supply
Outdoor
PTZ
Camera
115VAC Input,
50/60Hz
HubWayAv or
HubWayDv/Dvi
Video Balun
Combiner
Monitor
Rear
Front
1234CH 1-4 CH 5-8
28VAC
OFF
24VAC
+ DATA -
1-8
5678
PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE AC POWER
GAIN
87654321
Fig. 4
Typical Applications:
Fig. 4a - Optional hookup utilizing HubSat4D.
HubWayLD Active Isolated Unit - 7 -
(ON)
16
PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE AC POWER
GAIN
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
1 2 3 4 CH 1-4 CH 5-8
28VAC
OFF
24VAC
+ DATA --
1-8
+ DATA --
9-16
5 6 7 8 9 10 11 12 CH 9-12
28VAC
OFF
24VAC
13 14 15 16 CH 13-16
1.625"
41.28mm
17.625"
447.67mm
8.5"
215.9mm
19.125"
485.78mm
0.75"
19.05mm
TOP & BOTTOM
REAR
FRONT
Fig. 5
Illuminatedmasterpowerdisconnectcircuitbreaker:
• OFFpositionCircuitbreakertripped–Switchnotilluminated.
• RESET(ON)position–Switchilluminated.
Thelightningflashwitharrowheadsymbolwithinanequilateraltriangleisintendedtoalerttheusertothe
presenceofaninsulatedDANGEROUSVOLTAGEwithintheproduct’senclosurethatmaybeofsufficient
magnitude to constitute an electric shock.
Theexclamationpointwithinanequilateraltriangleisintendedtoalerttheusertothepresenceofimportant
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure. There
arenouserserviceablepartsinside.Referservicingtoqualifiedservicepersonnel.
Rack Mount Chassis Mechanical Drawing & Dimensions (H x W x D approximate):
1.625” x 19.125” x 8.5”(41.275mmx486mmx215.9mm)
- 8 - HubWayLD Active Isolated Unit
Altronix is not responsible for any typographical errors.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
website:www.altronix.com,e-mail:[email protected],LifetimeWarranty,MadeinU.S.A.
IIHubWayLD8Di/HubWayLD16Di J15N MEMBER
Mounting Options:
Fig. 6
Wall Mount Installation
1- Install mounting brackets (A) on the left and right side of rack chassis using
four (4) flat head screws (B) (included) (Fig. 7a).
2- Place unit at desired location and secure with mounting screws
(not included) (Fig. 7b).
Caution: It is necessary to
make sure mounting screws
are securely fastened to a
beam when installing the
unit vertically.
Rack Mount Installation
1- Remove and discard factory installed screws from both sides of rack chassis (Fig. 6a).
2- Install mounting brackets (A) on the left and right side of rack chassis using the
four (4) flat head screws (B) (included) (Fig. 6b).
3- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 6c).
Fig. 8
Fig. 7
Shelf Installation
1- Position and affix rubber pads (C) (included) at each
corner on the bottom of the unit (Fig. 8).
2- Place unit in desired location.
B
A
C
Mounting Hardware (Included):
BA
Fig. 7b
Fig. 7a
C
A
B
Fig. 6b
Fig. 6a Fig. 6c
Top Top Top
Front
Left
Front
Left
Front Left
Left Side
Rubber Pad
Two (2) mounting brackets
Six (6) flat head screws
for mounting brackets.
Four (4) rubber pads.
Remove
Dotted lines indicate studs
behind sheetrock.
Table of contents
Other Altronix Transceiver manuals
Altronix
Altronix HubSat4DiV User manual
Altronix
Altronix HubWayEX1 User manual
Altronix
Altronix Pace1ST User manual
Altronix
Altronix Pace1PTM User manual
Altronix
Altronix HubWay 8CD User manual
Altronix
Altronix NetWaySP4P User manual
Altronix
Altronix HubWayD Series User manual
Altronix
Altronix HubSat4WP User manual
Altronix
Altronix HubWay8D User manual
Altronix
Altronix HubSat4DV User manual
Altronix
Altronix HubSat4WPV User manual
Altronix
Altronix HubWay LD Series User manual
Altronix
Altronix eBridge1CT User manual
Altronix
Altronix eBridge1ST User manual
Altronix
Altronix Pace1PTM User manual
Altronix
Altronix HubSat8D User manual
Altronix
Altronix eBridge Plus 100TM User manual
Altronix
Altronix eBridge100STR User manual
Altronix
Altronix HubWayLD8D User manual
Altronix
Altronix PACE1ST User manual
