Overview:
Pace1ST is a long range hardened Ethernet transceiver designed for use with Pace1PRM, Pace4PRM, Pace8PRM
and Pace16PRM receivers. They transmit data at 100Mbps full duplex and power via CAT5e or higher cable in
a PoE(+) compliant format. Pace1ST will not deliver power to non-compliant devices, thus avoiding damage to
improperly connected non-PoE cameras/devices. The receiver passes the PoE(+) compliant power over the cable
to the Pace1ST transceiver which, in turn, passes this power to an enabled IP camera/device. These plug and
play units facilitate cost-effective solutions for IP devices that need to be installed at distances greater than 100m.
Features:
Agency Listings:
• UL/cUL Listed for Information
Technology Equipment (UL 60950-1).
• CE European Conformity.
Input:
• PoE (15W) IEEE 802.3af compliant or
PoE+ (30W) IEEE 802.3at compliant from
Pace1PRM, Pace4PRM,
Pace8PRM or Pace16PRM.
Ethernet:
• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair CAT5e.
• Speed: 10/100BaseT, half/full duplex,
auto negotiation.
PoE compliant to IEEE 802.3af (15W) and
PoE+ compliant to IEEE 802.3at (30W) delivered to
camera by Pace1ST.
• Throughput is rated to pass 100Mbps of data.
CAT5e or Higher:
• Distance: up to 500m @ 100Mbps.
LED Indicators:
• Green - PoE active.
•Yellow and Green LED IP Link status,
10/100Base-T/active.
Environmental:
• Operating Temperature:
For 15W: – 40ºC to 75ºC (– 40ºF to 167ºF).
For 30W: – 40ºC to 49ºC (– 40ºF to 120ºF).
• Storage Temperature:
– 40ºC to 75ºC (– 40ºF to 167ºF).
• Relative humidity:
20 to 85%, non-condensing.
Functions:
• Auto detection and protection of legacy
non-PoE cameras/devices.
Applications:
• Retrofit digital IP cameras in an analog
CCTV CAT5e installations.
• Extend Network link distance in an
industrial environment over 610m.
• Works with Megapixel, HD720, HD1080 and VGA
(SD) cameras with proper headend equipment.
Mechanical:
• Dimensions (W x L x H approx.):
2.27” x 2.645” x 1.12”
(57.7mm x 67.2mm x 28.4mm).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes
and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application.
Pace1ST is not intended to be connected to outside plant leads and should be installed indoors within the pro-
tected premises. Pace1ST is intended for indoor use only.
1. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s mounting hole
(Fig. 2a, pg. 3). Unit should be mounted in the proximity of camera/device.
2. Connect structured cable from IP camera/device to RJ45 jack marked [IP Device] (Fig. 2, pg. 3).
3. Connect CAT5e or higher to the connector marked [Pace Receiver] from receiver
(Pace1PRM, Pace4PRM, Pace8PRM or Pace16PRM) (Fig. 2, pg. 3).
Caution: once PoE connection is established between the receiver and Pace1ST, disconnection from Pace1ST will
not disable the PoE output voltage on the receiver. Although the Pace1ST can be reconnected, caution should be
taken not to connect the CAT5e wiring from the receiver to any non-PoE device.
Pace1ST
Hardened Transceiver
IP and PoE+ Over
Extended Distance CAT5e
Installation Guide
I.T.E. 43KC
