Amacam AM-VX1 User manual

High Definition
Ambarella A7 chipset
DASH CAMERA
User Manual
V3

– Do not expose the dash camera to dusty, dirty or sandy
conditions, if these gets into the camera or on the lens it can
damage the components.
– Do not expose the dash camera to high temperatures.
The normal operating temperature of the dash camera is -10 C
to 40 C (14F to 104F) and storage temperature is -20C to 80C (-
4F to 176F).
High temperatures can shorten the life span of electronic
device, and extremely high temperature will shorten the battery
life and/or degrade the plastic components. Note extreme
temperatures can be achieved in parked cars in direct sunlight.
Expose the dash camera to strong sunlight when using Motion
Detection mode may cause the dash camera to malfunction or
become damaged as the temperature can be too high in your car
in summer.
– Do not expose the dash camera to a cold environment.
Extremely low temperatures can also damage the electronic
components; if there is water moisture in cold environment,
freezing water can cause damage, as can thawing.
– Do not try to dismantle or open the casing. Doing so may result in
electrical shock and will most likely result in damaging the dash
camera.
– Do not mistreat the dash camera, dropping, sudden impact, and
vibration can cause damage.
– Do not clean the dash camera with chemicals, cleaning solution
or a high concentration detergent. Only a slightly damp cloth
should be used.
– Do not use a hardwire kit cable to connect the camera to
constant power supply for 24 hours recording for safety reason.
When the camera expose in summer sunshine the temperature
inside camera will be extremely high which may damage the
camera even your vehicle.
PRECAUTIONS

APPEARANCE
17
20
19
1
2
3
1, microphone hole
2, microSD slot
3, lens turning knob
4, miniUSB socket
5, GPS mouse in socket
6, AV-out socket
7, MIC indicator
8, power indicator
9, recording indicator
10, 1.5" LCD screen

APPEARANCE
11, MIC button
12, REC button
13, SOS button
14, menu button
15, power button
16, mounting base
17, reset button
18, cable conduit
19, vent holes
20, vent holes
1112131415

STANDBY MODE
When the camera is on standby mode, you can:
press
turn off
screen
switch
recording
and
playback
take a
photo
start
recording
turn
on/off
MIC
hold for 1
sec
turn off
camera
enter
recording
setting
Here is a quick instruction of the button operations on different
working modes:

RECORDING MODE
When the camera is on recording mode, you can:
press
turn off
screen
SOS lock
current
video
stop
recording
turn
on/off
MIC
hold for 1
sec
save
video and
turn off
camera
un-lock
current
video
PLAYBACK MODE
When the camera is on playback mode, you can:
press
turn off
screen
cancel,
switch
playback
and
recording
previous
item
next item
hold for 1
sec
turn off
camera

SETTING MODE
When the camera is on setting mode, you can:
press
turn off
screen
cancel
previous
item,
scroll up
next item,
scroll
down
hold for 1
sec
quit
setting
and turn
off
camera
quit
setting
LED OFF
no microSD
card detected or
card invalid
no power input,
or the camera
was turn off
LED blinking
recording &
writing to
microSD
battery invalid
GPS status
indicated and
GPS connecting
LED constant
on standby or
playback or
setting mode,
and card valid
external power
connected
MIC is ON,
or GPS status
indicated and
GPS connected

SETTING

SETTING

SETTING

SETTING

LANGUAGE
Here you can set the language you prefer.
options: ENGLISH
РУССКИЙ
SETTING

UI
RECORDING
Registrator Viewer
VIDEO AREA
PROGRASS
BAR
CONTROL
CENTER
FILE LIST
SPEED
G-SENSOR
DATA

camera box content