Amana RSKP0012 User manual

1
ATTENTIONINSTALLINGPERSONNEL
As a professional installer you have an obligation to know the
product better than the customer. This includes all safety
precautions and related items.
Prior to actual installation, thoroughly familiarize yourself with
this Instruction Manual. Pay special attention to all safety
warnings. Often during installation or repair it is possible to
place yourself in a position which is more hazardous than when
the unit is in operation.
Remember, it is your responsibility to install the product safely
andtoknowitwellenoughtobeabletoinstructacustomerinits
safe use.
Safetyisamatterofcommonsense...amatterofthinkingbefore
acting. Most dealers have a list of specific good safety
practices...follow them.
The precautions listed in this Installation Manual are intended
as supplemental to existing practices. However, if there is a
directconflictbetweenexistingpracticesandthecontentofthis
manual, the precautions listed here take precedence.
RECOGNIZE THIS SYMBOL
AS A SAFETY PRECAUTION.
Description
Control board installation procedures are described in detail in
these instructions. Read and follow these instructions carefully
beforereplacingthecontrolboard.Failuretodosomayresultin
control board damage. Pages 3 through 5 are procedures for
programmingthecontrolboardandthediagnosticcodesforthe
control board.
PTAC CONTROL BOARD KIT
RSKP0012
I NSTALLATION I NSTRUCTIONS
Important Note:
Damagetothecontrolboardcanoccurfromfailuretodisconnect
powersupplyorfailuretosetthemasterswitch(locatedonthe
controlboard) to OFFbefore removing thelowvoltage terminal
stripcoverfromaninstalledcontrolboard.Damagetothisboard
bynotfollowingtheseinstructionsisconsideredmisuseandnot
coveredundereitherthestandardunitwarrantyoranyextended
service contract.
ImportantNote:
All warranty replaced boards must be returned to the parts
source from which they were purchased to insure proper war-
ranty credit.
ElectrostaticDischarge(ESD)Precautions
Beforeremovingthenewcontrolboardfromthestaticwrap,itis
very important to discharge any static electricity. This can be
accomplishedintwomethods. Servicercanwearagroundstrap
or by touching the metal chassis before replacing the board.
ExistingControlBoardRemovalProcedures
1. Disconnect electrical power to the unit.
2. Removefrontcover.
3. Remove the two mounting screws, one on each side of
controlboardcover.Liftthecoveruptogainaccesstothe
ribbonconnector.Unplugribbonconnectorfromcontrol
boardandremovecovercompletely.Removethescrewon
right side of the control panel.
4. If a remote thermostat or any low voltage accessory is
beingused,removethelowvoltagepinconnectorfromthe
low voltage terminal strip.
5. Removethewiresfromthecontrolboardandunplugthe
thermistors from the control board. Remove the four
screwsthatsecurethecontrolboardtothecontrolpanel
and remove the existing control board.
®
isatrademarkofMaytagCorporationandisusedunderlicensetoGoodmanCompany,L.P. Allrightsreserved.
5151 San Felipe, Suite 500 • Houston, TX 77056
www.amana-ptac.com
©2014,2016 GoodmanCompany,L.P.
IO-823A
July 2016

2
New Control Board Removal Procedures
6. Set the new control board in place and reattach to control
panel with the four screws removed in Step 5.
7. Reconnect the wires across the top terminals of the control
board (Refer to Figure 1).
8. Installhighandlowvoltagewiresfromthetransformertothe
control board.
9. Reconnect the thermistors to the control board. The Black
thermistor connects to the IAT BLACK terminal and the Red
Thermistor connects to the ICT RED terminal on the control
board. The Yellow Thermistor connects to the IDT YELLOW
terminal on the control board.
10. If any remote thermostat or low voltage accessory is being
used, reconnect the low voltage pin connector to the low
voltage terminal strip on the control board.
11. The control board cover is now ready to be installed. The
ribbonforthetouchpadwillneedtobereconnectedtothe
controlboard. Takecautionnottobendorfoldthe ribbon
(Seefigure1forribbonconnection).Ensurethatnowiresare
pinchedorcaughtbetweenthecoverandthepanelandthen
reinstall the screws removed in Step 3.
*CRITICAL STEP*
This service control until it has been
configured to control a heat pump or cooler. As long as
the display shows Eo, the unit .
Follow the directions on Pages 4 and 5 to set feature
codes C3 and “dd”.
For C3, select option H if the unit is a heat pump or option
C if the unit is a cooler with or without electric heat.
For HE* and 32* models, configuration code “dd” must be
set to correct cooling capacity: 7,000, 9,000, 12,000
15,000 or 17,000 btu’s.
will not operate
will not operate
Failure to set “C3” and “dd”
configuration codes correctly will cause the unit to not
operate properly.
12. Setthe master switch to theON position, restore electrical
power and verify that the unit is functioning correctly.

3
BK
DANGER HIGH VOLTAGE
24VAC TRANSFORMER
12VA CLASS 2 ONLY
ON OFF
MASTER SWITCH
HEATER 1 HEATER 2
LINE 1
IN1 COM IN2
A
UXILIARY
CR
GL W2 Y/W1 B GH
REMOTE THERMOSTAT
IAT
BLACK
ICT
RED OCT
BLUE IHD
ORANGE OAT
GREEN IDT
YELLOW
REV.
VALVE
FAN
HIGH LOW
OD
FAN
HIGH LOW
LINE 2 COMPRESSOR
L2
L1
MC
9
BK
BK
7
OR
RD
TB
EM
FAN
MOTOR
CM
FAN
MOTOR
TR 1
265
230
S
ID
OR
13
BK
DANGER HIGH VOLTAGE
24VAC TRANSFORMER
12VA CLASS 2 ONLY
ON OFF
MASTER SWITCH
HEATER 1 HEATER 2
LINE 1
IN1 COM IN2
A
UXILIARY
CR
GL W2 Y/W1 B GH
REMOTE THERMOSTAT
IAT
BLACK
ICT
RED OCT
BLUE IHD
ORANGE OAT
GREEN IDT
YELLOW
REV.
VALVE
FAN
HIGH LOW
OD
FAN
HIGH LOW
LINE 2 COMPRESSOR
L2
L1
MC
9
BK
BK
7
OR
RD
TB
EM
FAN
MOTOR
CM
FAN
MOTOR
TR 1
265
230
S
ID
OR
13
M70ControlBoard
Figure 1

4
ConfigurationSettings
Thecontrolcanbeconfiguredtooperateawiderangeofoptions.
The options listed below with the * are the factory default
settings. Iftheseareacceptable,thentheunitdoesnotrequire
anyadditional configurationand isfullyoperable. To configure
the unit, first select the configuration feature code setting and
thenan optioncode tochangefrom thefactory defaultsetting.
Toenter configuration feature mode:
1. Press andcontinue to hold theupand down arrow keys
andquicklypresstheOFFkeytwicewithinatwo(2)second
timeframe. Thelowerright doton thedisplaywillflash,
and the display will indicate a double dash ( - - ). Press
theHEATkeyonetime. Thedisplaywillalternatebetween
displaying the feature code C1,for example, and the
option code 0 (factory default setting).
Toselectaconfigurationfeaturecode,presstheHEATkey
until the desired configuration comes up. To scroll to a
previously viewed configuration codes press the COOL
key.
Onceyouhavescrolledtothecorrectfeature,thenselect
the option code for your desired configuration. Press
eithertheUP orDOWN key toscrollthroughtheoptions
oftheselectedfeaturecode.
Toexitconfigurationmode:
1. Press the OFF key. Configuration feature mode will also
exitifnokeysarepressedforaperiodoftwo(2)minutes.

5
ConfigurationSettings
*Indicates factory default
See manufacturer for additional configuration options.
Configuration Code Configuration Feature Option Code Option
0 * Chassis Membrane*
L5 Wired Thermostat
rE Wireless Stat & 7-Button
L0 Locked Membrane
Au do not use
On do not use
bP Button present
bA* Revert to Cyclic
A Always run fan (even if Off)
Cdo not use
bC Revert to Continuous
C Cooler Only PTC
H* Heat Pump PTH *
0 Sevice No Operation "Eo"
dC Dry Cooler DRY
dH do not use
uC do not use
uH do not use
C4 Room I.D. Di
g
it 1 & 2 00* - 99 00* - 99
C5 Room I.D. Di
g
it 3 & 4 00* - 99 00* - 99
0* Off*
1On
18 18 Hour Automatic Entry
2 Bound T-stat PIR w/o Door
C8 Tem
p
. Limitin
g
Cool 60* - 80 60* - 80
C9 Tem
p
. Limitin
g
Heat 68 -90, 80* 68 - 90, 80*
8* B*
0O
c3 Un-rent ClnTem
p
.45 -95, 79* 45 - 95, 79*
c4 Un-rent HtnTem
p
.45 -95, 63* 45 - 95, 63*
0* Not Twinned*
5Twinned
F* Fahrenheit Scale*
CCelsiusScale
L* On, Low Fan*
HOn,HighFan
0Off
d6 Sensorless Un-Occ. Time 1 - 32,18* 1 - 32,18*
d7 1st Un-Occ. Set Back Temp. 1 - 16, 2* 1 - 16, 2*
d8 1st Un-Occ. Set Back Time .1, .5*, 1 - 24 .1 ,.5 ,1 - 24, .5*
d9 2nd Un-Occ.Set Back Temp. 1 - 16, 3* 1 - 16, 3*
dA 2nd Un-Occ. Set Back Time .5, 1*- 24 (d8)- 24,1*
db 3rd Un-Occ. Set Back Temp. 1 - 16, 6* 1 - 16, 6*
dC 3rd Un-Occ. Set Back Time 1 - 24,3* (dA)- 24,3*
dd CoolingCapacity 7,9,12, 15,17 7,000,9,000, 12,000, 15,000, 17,000 BTU
dF Platform Group Code 00* - 99 00*- 99
dH ElectricHeater Size 00*, 15,20, 25,35, 50 00*,15, 20,25, 35,& 50
dJ Operating Voltage 2,3*,4,5 2,3*,4,5
r4 Room Prefix 00* - 99 00* - 99
r5 Room Suffix 00* - 99 00* - 99
0* Dis-enabled*
78 - 99 78 - 99
0* Door Switch
1 Motion Sensor
2FrontDesk
3 Wired Un-rented Set Back
4EmergencyHydronic
5 Load Shedding
6AlarmSensor
0* Door Switch
1 Motion Sensor
2FrontDesk
3 Wired Un-rented Set Back
4EmergencyHydronic
5 Load Shedding
6AlarmSensor
uL Config. Security Code 00* - 99 00*- 99
u9 Input Pins UN2 & COM
u3 Heat Protection
u8 Input Pins UN1 & COM
Cd English / Metric Temp
CE Freeze Protection
C0 T-stat B/O Term.
CA Wireless Twin Unit
C3 Reverse Cycle Operation
C6 Wired Occupancy
C1 Interface
C2 IDFan Operation

6
The Diagnostic Maintenance & Status Report provides detailed
information on PTAC control operation and operational status
including present modes, failures, airflow restriction warnings,
operatingtemperatures,andpastfailures. Thelowerrighthand
dotonthecenterdisplayflashesinthismode.Insomecasesthe
greenLEDlocatedinthelowerlefthandcornerofthetouchpad
belowtheOFF keywillalsobelit. ThisGreenLED“StatusLight“
onlyilluminatesifthereisanstatuscodethathasbeenactivated
andshouldbereviewed. Inmostcases,thislight indicates that
the indoor room filter is dirty should be cleaned or replaced.
NOTE:Dirtyfilterscausetheunittoconsumemoreenergythan
normallyneededtoconditiona room. Once the filter has been
cleaned or replaced, the LED should go out. If the LED is still
illuminated after the filter has been cleaned, activate the Diag-
nosticandStatusmode to view any active codes. The unit may
need additional cleaning or maintenance of the evaporator or
condenser coils. Please perform this step before calling a
servicer. Aservicershouldbecalledonlyifcleaningthefilteror
coils does not clear the status code or the code indicates that
servicershouldbecalled.
DIAGNOSTICSTATUSREPORTMODE.
ToenterDiagnosticStatusReportmode,pressandholdtheup
anddown arrowsand,whileholding,quicklypresstheCOOL
key twice.
ACTIVEFAILURES.
• If there are no active failures or lockouts, the display
will show a double dash, “- -”. If there is a code listed,
see the unit “Diagnostic Codes” chart for a list of defini-
tions.
DiagnosticMaintenance&StatusReport OPERATINGTEMPERATURES.
• If not in Diagnostic Status Report Mode, enter as in-
structed above and press the Fan Speed key.
• If already in Diagnostic Status Report mode, press the
FanSpeed key. Thedisplaywillshowthetempera-
ture of the desired set point, SP; the temperature at the
wirelessthermostat,rL;theindoorambienttemperature
behind the filter, IA; the indoor coil temperature, IC; the
indoor discharge air temperature, Id; the outdoor coil
temperature,OC;theoutdoorambienttemperature,OA;
andthespareprobetemperature,IH. Ifanyoftheprobes
are not populated the display will show the correspond-
ing failure code.
PASTFAILURELOG.
• If not in Diagnostic Status Report Mode, enter as in-
structedaboveandpresstheFanSpeed keytwice.
• If already in Diagnostic Status Report mode, press the
Fan Speed key. While the display is showing oper-
ating temperatures, the last 10 failure codes active or
past can be requested by pressing the Fan Speed
key again. The codes are displayed last entry first fol-
lowed subsequently by each preceding code.
Note that modes F1 and Fd are also displayed in the normal
control operation (see “Diagnostic Codes” chart).
ToexitDiagnosticStatusReportmode,presstheOFF key.

7
DiagnosticCodes
STATUS DISPLAY ERROR
LIGHT SUGGESTED ACTION
FP Freeze Protection Engaged. The room temperature
measured by the wireless remote thermostat or indoor
ambient thermistor active sensor falls below 40°F. YN
No Action required. This setting will disengage when
the room temperature rises above 43°F.
Fd Front Desk switch is closed. All outputs are switched off. Y N Open front desk switch to allow occupant unit
operation.
Eo Un-Configured Service Board -
All operation held awaiting configuration YY
Enter Configuration Menu and set "C3" to "C"
for coolers with electric heat or "H" for heat pumps.
EH Emergency Hydronic En
g
a
g
ed. The EHH switch is closed.
Compressor is switched off. YN
Open front emergency hydronic switch to allow
occupant unit operation.
LS Load Shedding Engaged. The LS switch is closed.
Compressor and Electric heat is switched off. YN Open load shedding switch to allow occupant unit operation.
On Control is configured to respond to a wired thermostat Y N No action if a wired thermostat is being used.
Otherwise, see Configuration Settings.
oP Open Door Lockout
(DS1 & DS2 open; wireless) YY Close Room Door. Unit will not condition space with door open.
nP Window Switch Lockout -
(LS & INN open) YY Close Room Door or Window. Unit will not condition space with door or window open.
HP Heat Sentinel -
(WIAT > u3) YN
No action required. This setting will disengage when
the room temperature falls.
Ur Un-Rented Status
(EHH & INN or wireless) YN
Front Desk needs to set to Rented mode (if
applicable).
Indoor Ambient Thermistor reads outside the
range -20°F to 200°F &the wireless thermostat is not
communicating to the unit control or
Indoor Ambient Thermistor (IAT) without a wireless remote
thermostat reads outside the range -20°F to 200°F.
F2 Wireless Remote Thermostat failure N N Replace Wireless Thermostat.
F3 Indoor Ambient Thermistor reads
outside the range -20°F to 200°F Y N Replace black Indoor Ambient Thermistor.
F4 Indoor Coil Thermistor either above
or below operating tolerances. N Y Replace Red Indoor Coil Thermistor .
F5 Wireless Thermostat failure. N Y Attempt to rebind Wireless Thermostat
or Replace Wireless Thermostat.
F6 Indoor Discharge Thermistor either above
or below operating tolerances. NY Replace Yellow Indoor Discharge Thermistor.
Fb Low Remote Battery Warning. N Y Replace Batteries in Wireless Devices.
H1 High Voltage Protection engaged.
Power supply voltage is to high. Y N Check for incoming power at correct voltage.
br Brown Out Protection engaged.
Power was lost or voltage is low. N N Check for incoming power at correct voltage.
L6 Discharge Air Too Hot. N Y Clean Filter or Remove Air Blockage.
LC Outdoor Coil Thermistor temperature high. N Y Clean Condenser Coils, Check Fan for
fault. Code will reset after cleaning.
C2 Indoor Air Recirculation. Large delta between thermostat and
return. NY
Clean Filter or Remove Air Blockage or Close
Vent Door or Improve indoor to outdoor seal.
C5 Outdoor Coil temperature too high for outdoor ambient
temperature. N Y Check for Blocked Outdoor Air or Clean Coil.
Replace black Indoor Ambient Thermistor or
Wireless Remote Thermostat.
AIRFLOW
ALERTS
CODE
MODESFAILURES
F1 YY
C1 Indoor Coil is freezing up. N Y Clean filter, Check for fan and blower operation,
Check for Refrigerant loss
or Restricted capillary tube.
C3 Indoor Coil is freezing up. N Y Clean filter, Check for fan and blower operation,
Check for Refrigerant loss
or Restricted capillary tube.
C4 Indoor Coil froze up. N Y Clean filter, Check for fan and blower operation,
Check for Refrigerant loss
or Restricted capillary tube.
C6 Poor Unit Performance. N Y Check for blower motor, compressor,
or electric heat operation.
C7 Indoor Freezing Lockout (ICT - IAT > 20) +10 Min N Y Clean filter, Check for fan and blower operation,
Check for Refrigerant loss
or Restricted capillary tube.
REFRIGERATION
ALERTS

8
5151 San Felipe, Suite 500 • Houston, TX 77056
www.amana-ptac.com
®is a trademark of Maytag Corporation and is used under license to Goodman Company, L.P. All rights reserved.
NOTE: SPECIFICATIONS AND PERFORMANCE DATA LISTED HEREIN
ARE SUBJECT TO CHANGE WITHOUT NOTICE
Quality Makes the Difference!
All of our systems are designed and manufactured with the same high quality standards regardless of size or
efficiency. We have designed these units to significantly reduce the most frequent causes of product failure.
They are simple to service and forgiving to operate. We use quality materials and components. Finally, every
unit is run tested before it leaves the factory. That’s why we know. ... There’s No Better Quality.
Visit our website at www.amana-ptac.com for information on:
• Products • Parts
• Warranties • Contractor Programs and Training
•CustomerServices • Financing Options
®2014, 2016 Goodman Company, L.P.