NAPCO Gemini GEM-P3200 User manual

INSTALLATION
INSTRUCTIONS
HARDWIRE WIRELESS
GEM-P3200
CONTROL PANEL/COMMUNICATOR
WI817C 08/00© Napco 2000
R
R
COMPUTERIZED SECURITY SYSTEM
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
D
E
F
G
NEXT/YES
PRIOR/NO
AREA
GEMINI
ENT A1
48
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
GEM-RP2ASe2
R
COMPUTERIZED SECURITY SYSTEM
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
D
E
F
G
NEXT/YES
PRIOR/NO
AREA
GEMINI
READY
AC ON
READY
AC ON
GEM-RP1CAe2
R
COMPUTERIZED SECURITY SYSTEM
GEMINI
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
DE
F
G
NEXT/YES
PRIOR/NO
AREA
SYSTEM ARMED
01/01/00 12:00 AM
GEM-RP3DGTL

CHANGES FROM PREVIOUS EDITION
The following changes have been made to this manual (WI818D) since the last edition (WI818C).
New GEM-P3200 Version 20 Features:
! New Easy Menu Programming allows the system to be completely programmed through Menu Driven Easy
Program Mode. Requires the use of the following version keypads:
• GEM-RP1CAe2, Version 6
• GEM-RP2ASe2, Version 5b
• GEM-RP3DGTL, Version 1c
! Maximum Wireless Zones expanded from 32 to 48
! Maximum Number of Users expanded from 32 to 48
! Chime 2 zone provides second distinct pulsating “Chime Zone” tone
! Set System Time and Date in User Program Mode
! System Trouble Audible Automatic Timeout
! Inhibit System Trouble Audible
! Easy Programming of PC Preset Auto download ID and Callback Numbers
! Support of GEM-PRINT module
! Cancel Reporting Code
! Wireless Trouble Reporting by Zone
! Pager (Telco 3) Reporting Delay
! Pager - Programmable Number of Reports of Same Signal
! Pager - Maximum Number of Consecutive Pages
! Specific Logging of Communication Failure Modes
! New Relay Event “Area Disarmed” (PCD3000 programmable only)
! Programmable DST start date (PCD3000 programmable only)
! 20 Digit Dialing Prefix
NOTE: Typically, any version GEM-P3200 control panel could be upgraded to the latest firmware by replacing the
EPROM with a newer version. This is no longer the case. The Firmware Version 20 EPROM must only be used in a
Version 18 (or greater) PCBoard. Do NOT attempt to upgrade a GEM-P3200 control panel which currently is running
Firmware Version 11C (or prior) to version 20 (or greater) by replacing the EPROM.
The PCBoard version ( triangle number) is printed on a triangular shaped sticker affixed to the GEM-P3200 circuit board.
THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN CONTROL PANEL
FIRMWARE VERSION 20 OR LATER.
NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: [phone]
For direct line to Technical Service, call toll free: [phone]
Internet: http://www.napcosecurity.com
Upon entering program mode, the keypad display will flash the control panel
firmware version, followed by the keypad firmware version:
GEM-RP1CAe2: [2006], GEM-RP2ASe2: [205b], GEM-RP3DGTL: [20/1C]

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 3
TABLE OF CONTENTS
Refer to accompanying GEM-P3200 Programming Instructions (WI818) for programming information.
INTRODUCTION...............................................................4
General Description .....................................................4
Features.......................................................................4
Specifications...............................................................6
Ordering Information ....................................................6
Summary of UL Requirements.....................................8
INSTALLATION................................................................9
Mounting ......................................................................9
Wiring...........................................................................10
Wireless Systems ........................................................10
Typical Residential Fire Installation .............................10
Typical Partitioned Installation .....................................10
UL Commercial-Burglary Installations..........................11
Testing the System ......................................................12
WIRING CONNECTIONS .................................................13
Battery..........................................................................13
Transformer .................................................................13
Siren/Bell Output..........................................................13
Auxiliary Alarm Output .................................................13
PGM Outputs ...............................................................13
Remote Bus .................................................................14
Earth Ground ...............................................................14
Auxiliary Power ............................................................14
Reset Output................................................................15
Basic Zone Configuration.............................................15
Expanded Zone Configuration .....................................15
4-Wire Smoke Detectors..............................................16
2-Wire Smoke Detectors..............................................16
Telephone Lines ..........................................................17
KEYPAD CONFIGURATION MODE ................................18
Keypad Installation.......................................................18
Configuring the Keypads..............................................18
BASIC OPERATION.........................................................21
User Codes & Zone Descriptions.................................21
Arming and Disarming the System ..............................22
Bypassing Zones .........................................................24
Alarm Indication ...........................................................24
Function Mode .............................................................25
Keypad Messages .......................................................30
GLOSSARY ......................................................................31
STANDBY-BATTERY CALCULATION WORKSHEET... 53
WIRING LEGEND ............................................................ 54
KEYPAD PROGRAMMING MODES ............................... 55
GEM-P3200 WIRING DIAGRAM ..................................... 61
STATEMENT FOR CANADIAN MODELS (DOC) ........... 52
FCC STATEMENT ........................................................... 63
LIMITED WARRANTY ..................................................... 64
NOTE: THESE INSTRUCTIONS ARE INTENDED AND WRITTEN FOR PROFESSIONAL INSTALLATION PERSONNEL HAVING SUITABLE
TRAINING, EXPERIENCE AND INSTALLATION EQUIPMENT. IT IS RECOMMENDED THAT AFTER PROGRAMMING, THE ERROR CHECK
UTILITY OF THE PCD3000 DOWNLOADER BE USED TO VERIFY THAT THE CONTROL PANEL PROGRAM CONTAINS NO ERRORS OR
CONFLICTS WHICH MAY INHIBIT ITS INTENDED OPERATION.

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 4
INTRODUCTION
GENERAL DESCRIPTION
NAPCO's Gemini GEM-P3200 is a state-of-the-art microcomputer-based burglary and residential fire alarm control panel
of modular design. Integrally an 8-zone panel, it will support up to 32 hardwire zones with optional zone expansion
modules, and/or GEM-RP1CAe2 Keypads, and up to 48 wireless zones with the optional wireless receiver modules.
Each panel includes an integral digital communicator.
The control panel features programmable area partitioning. That is, the system may be divided into up to two discrete
multiple-zone areas, each allowing access by only those users programmed for their respective area.
Opening Suppression and Closing Suppression, available through Napco Quickloader software, suppress reporting within
programmed “windows”. Conversely, Exception Reporting can transmit a “fail to close” if the panel is not armed within
programmed intervals and, similarly, a “fail to open” if the panel is not disarmed within programmed intervals.
Furthermore, the panel can be programmed to automatically arm either area at any time. A log containing up to 800
events (accessible through QuickloaderTM software) monitors control-panel activity referenced to a precision real-time
clock. A detailed event history may be displayed at the computer, using NAPCO's PCD3000 Quickloader Software.
Keypads feature a liquid-crystal display for messages. In normal use, the LCD shows zone identification and status
messages. Conventional LEDs and a sounder are also provided for annunciation.
Data may be quickly and easily downloaded to the control panel using a PC-compatible computer with NAPCO's
PCD3000 Quickloader software and PCI2000 computer interface. Or, the panel may be programmed using the keypad in
its secondary mode of operation. In the keypad programming modes (there are two: Dealer and User), the LCD shows
memory address, data values, programming prompts, and the alphanumeric characters required for entering up to 32
user codes and custom zone descriptions.
GEM-P3200M
The standard GEM-P3200 may be converted to the Mercantile “GEM-P3200M” version with the optional accessory,
H1217. The H1217 kit includes the model H217 heavy-duty UL commercial enclosure, the required (2) tamper switches
and required tamper screws.
Note: Do not use Fire Zones in a Mercantile installation.
FEATURES
Control Panel Features
! Eight end-of-line-resistor burglary zones programmable for Area, Exit/Entry Delay, Interior, Follower, Day Zone,
Chime, Fire options, Sensor Watch, Swinger Shutdown, Zone Anding and a variety of other features.
! Supports up to 32 hard-wire zones with optional zone-expansion modules and 4-zone keypads.
! Supports up to 48 wireless zones with optional wireless receivers.
! Supports up to 48 individually coded users, each with a programmable authority level.
! Supports three on-board relay outputs and up to 24 external relay outputs.
! Supports three keypad panics: Fire, Police & Auxiliary
! Supports up to 2 independent area partitions.
! Supports up to 8 separate access stations by up to 48 users.
! Supports up to 24 separately-addressable X-10 devices with the GEM-X10KIT and PC04 interfaces.
! English-language prompts & system status messages.
! User-customized zone descriptions, re-programmable as required.
! Supports 2-wire and 4-wire smoke detectors.
! Reports alarms, restores and troubles by zone.
! 255 Event Schedule
NOTE: Failure to install and program as described in this manual for UL-listed systems voids the listing mark of
Underwriters Laboratories, Inc.

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 5
! 800 Event Log.
! Overview Mode permits monitoring and control of total system from one keypad.
! Guard-Tour programmable for start time, tour length, and check points (tour stations).
! Two programmable entry delay times.
! Two Interior-Zone groups.
! Dynamic battery test interrupts charging and places battery under load every four hours.
! Chime by zone; programmable duration.
! Non-volatile RAM retains memory during power losses.
! Quickloader programmable.
! Auto-Download Log.
! Exclusive V.A.L.I.D. feature (Verifying Automatic Line-Integrity Diagnostic) reduces false alarms due to changes in
line resistance.
Communicator Features
! Compatible with all major receiver formats, including BFSK, 4/2, Modem 2, SIA, 4/3/1, 4+2 Express and Point ID.
! Rotary dial and TouchToneTM with Rotary backup.
! Three 20-digit telephone numbers.
! Backup Reporting; Double Reporting; Split Reporting.
! 48 User Codes with Opening/Closing Reporting by user.
! Ac Failure Reporting with programmable report delay.
! Supervised telephone line with programmable delay.
! Pager capability.
Keypad Features
! English-language LCD display; LED and sounder annunciators.
! Supports up to 7 4-wire keypads.
! Access only capability.
! Provisions for fire, police and auxiliary panic alarms.
! Integral 4-zone EZM included in each keypad (GEM-RP1CAe2 only).
! Communicator Test to Central facilitates testing; Locate, Fault-Find and EZM-Locate diagnostics simplify
troubleshooting.
! PGM output.

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 6
SPECIFICATIONS
GEM-P3200
Panel Dimensions: 12.375” x 13.875” x 3.55” (H x W x D)
Operating Temperature: 0-49°C (32-120°F)
Input Power: 16.5VAC via CLASS 2 Plug-In 40VA or 50VA Transformer
Loop Voltage: 10-13Vdc
Loop Current: 2.4mA with 2.2KΩend-of-line resistor (Model EOL2.2K); 5mA for 2-wire smoke-detector zones.
Loop Resistance: 300Ωmax.; 50Ωfor 2-wire smoke-detector zones
Relay Outputs (Burglary; Reset; Aux): Wet, 12Vdc, 1.2A max.; Dry (cut related jumper for dry contacts; see Wiring
Diagram), SPDT contacts 24Vdc, 2A, 0.6 PF
Auxiliary Power Output: 12Vdc regulated
Remote Power Output: 12Vdc regulated (for keypads)
Combined Standby Current (Remote Power + Aux. Power + Reset Relay Power): See following charts.
Note: (1) With 1 RBAT6 battery, GEM-
P3200 combined standby current + PS3002 standby current may not exceed 1.2A.
(2) W(2) With 2 RBAT6 batteries, GEM-P3200 combined standby current + alarm current may not exceed 1.9A
(3) Not evaluated by U.L.
Standby Time: Residential Fire/Burglary & Commercial Burglary, 4 hours minimum
EZM Module: GEM-EZM8: Input, 50mA (not including PGM output)
PGM Output: 5mA, 12V Special Application
Keypad Current: GEM-RP1CAe2: 100mA; 35mA if backlighting is disabled (cut W1, W2 & W3)
GEM-RP2ASe2: 50 mA
GEM-RP3DGTL: 50 mA
PGM Output: 5mA, 12V Special Application
Maximum Number of Keypads: 15
Maximum Wiring Length for each run (#22AWG): 1000' divided by total number of keypads and EZMs on run
Keypad Dimensions: 4” x 5” x 1” (H x W x D); 11.1cm
ORDERING INFORMATION
System Components
GEM-P3200: Residential UL-Listed Burg Control Panel.
GEM-RP1CAe2: 32-Character LCD Burg & Residential Fire Keypad with 4 EOL Zones.
GEM-RP2ASe2: LCD Burg & Residential Fire Keypad with remote panic.
GEM-RP3DGTL: Digital Burg and Residential Fire Keypad with remote panic.
RESIDENTIAL BURGLARY & COMMERCIAL BURGLARY
TRANSFORMER RECHARGEABLE
BATTERY
POWER
SUPPLY
GEM-P3200
COMBINED
STANDBY CURRENT
GEM-P3200
ALARM
CURRENT
POWER SUPPLY
STANDBY
CURRENT
STANDBY
TIME
TRF11 (16.5 VAC, 40 VA) RBAT4 (12 VDC, 4 AH) N/A 650 mA 2.0 A N/A 4 Hours
TRF11 (16.5 VAC, 40 VA) RBAT6 (12 VDC, 6 AH) N/A 650 mA 2.0 A N/A 6 Hours
TRF11 (16.5 VAC, 40 VA) (3) RBAT6 (12 VDC, 6 AH) PS3002 (13.2 VDC, 1.9 A) 650 mA (1) 1.9 A (2) 1.2 A (1,2) 4 Hours
TRF11 (16.5 VAC, 40 VA) (3) 2 RBAT6 (12 VDC, 6 AH) PS3002 (13.2 VDC, 1.9 A) 650 mA 1.9 A 1.4 A 4 Hours
RESIDENTIAL FIRE, COMBINATION RESIDENTIAL FIRE & BURGLARY
TRANSFORMER RECHARGEABLE
BATTERY
GEM-P3200
COMBINED
STANDBY CURRENT
GEM-P3200
ALARM
CURRENT
STANDBY
TIME
TRF11 (16.5 VAC, 40 VA) RBAT7 (12 VDC, 7 AH) 150 mA 650 mA 24 Hours

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 7
Optional Accessories and Peripherals
EOL130: 2-Wire Fire Zone Resistor, 130W, 3W
EOL2.2K: End-of-Line Resistor Assy., 2.2K for Fire Circuit
FT2200: End-of-Line Relay/Resistor Supervisory Module
GEM-DT: Wireless Dual-Technology Sensor **
GEM-EVA 1: Electronic Voice Annunciator *
GEM-EZM4: 4-Zone Expansion Zone Module
GEM-EZM8: 8-Zone Expansion Zone Module **
GEM-GB: Wireless Glass-Break Detector **
GEM-KEYF: Key Fob Transmitter **
GEM-HEAT Wireless Heat Detector **
GEM-PIR: Wireless PIR **
GEM-PRINT: Parallel Printer Interface *
GEM-RECV8: Wireless Receiver, 8 Zones **
GEM-RECV16: Wireless Receiver, 16 Zones **
GEM-RECV96: Wireless Receiver, 96 Zones **
GEM-RS232KIT: Home Automation Interface *
GEM-SMK: Wireless Smoke Detector **
GEM-TRANS2: Window/Door Transmitter, 2-Point **
GEM-WP: Waterproof Panic Transmitter **
GEM-X10KIT: X-10 Interface *
H1217:Mercantile Conversion Kit
PCD3000: Downloading Software for IBM PC-Compatible
PCI2000/3000: Software with Interface for IBM PC-
Compatible Computer
PCI-MINI: Notebook Computer Interface *
PS3002: Power-Supply Module, 13.2Vdc, 1.9A
RB1000: Relay Board *
RBAT4: Rechargeable Battery, 12Vdc, 4AH
RBAT6: Rechargeable Battery, 12Vdc, 6AH
RBAT7: Rechargeable Battery, 12 VDC, 7AH
RBATH1: Dual Battery Harness *
RM3008: Relay Module (in enclosure)
RPB-3: Universal Junction Box
TRF11: Transformer, 16Vac/40VA, Class 2
TRF14: Transformer, 16Vac/50VA, Class 2
WIZARD IIe: Telephone Interface Module *
WL1: Wire Assembly with Lug Connector, 20”
VERI-PHONE: Two-Way Voice/Listen-In Module *
W834-1: Keypad Cable, plug-in (20”)
OI163: Instruction Manual, GEM-P3200
OI192: Instruction Manual, GEM-RP2ASe2
OI193: Instruction Manual, GEM-RP1CAe2
OI249: Instruction Manual, GEM-RP3DGTL
WI818: GEM-P3200 Programming Manual
* Not investigated by UL.
** Not investigated by UL for commercial applications.
UL LISTINGS
Household Burglar Alarm System Units: UL1023
Household Fire Warning System Units: UL985
Local Burglar Alarm Units and Systems: UL609
Central Station Burglar Alarm Units: UL1610
Police Station Alarm Units: UL365
COMPATIBLE UL-LISTED DEVICES
Refer to the following list of recommended devices.
Bells:
Ademco AD8-12; AD10-12
Amseco MBL-8/12V; MBL-10/12V
Wheelock 46T-G4-12-R*; 46T-G6-12-R; 46T-G10-12-R
Hochiki America AL-VB-1012*; AL-MB-612*
*Not for Household Fire applications (<85dB at 10')
Grade-A Bell:
Ademco AB-12 Bell in Box
Horns:
Wheelock 34T-12-R; MT-12/24; MT4-12/24; MIZ-12
Faraday 6120-0-0-12-DC*
Federal Signal 450E-24
Hochiki America AL-FH-12M*
*Not for Household Fire applications (<85dB at 10')
Mini-Horn:
Federal Signal 460-024-R (red); -W (white); -BG (beige)
Chimes:
Wheelock CH-CF1-12; CH-DF1-12 (both for private-mode
signalling only)
Strobes:
System Sensor SS1215ADA; SS1215ADAB
Wheelock LS12
Strobe/Horns:
Wheelock 7002T-12-W-FR; 7001T-12-W-FR; V7001T-12-
W-FR
Gentex SHG-12H
System Sensor MASS1215ADA; MASS1215ADAB
Electronic Signals:
Wheelock ES-BH2-R; ES-DL2-R; ES-EL2-R
Electronic Signal/Strobes:
Wheelock ES-BH2-WH-12DC-HF-R; ES-DL2-WS-12DC-
VF-R; ES-EL2-WS-12DC-HF-R
Bell/Strobes:
Wheelock 46T-G6-12-WS-12-HF-R; 46T-G10-12-WS-12-
HF-R
Transformers:
Basler Electric BE116240CAA 40VA; BE116250CAA 50
VA

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 8
SUMMARY OF UL REQUIREMENTS
Residential
! Recognized Limited-Energy Cable for initiating, indicating and supplementary circuits.
! Initiating loops supervised if longer than 3 feet
! FT2200 End-of-Line Relay for Fire (if using 4-wire smoke detectors)
! Minimum alarm timeout of 5 minutes
! Maximum exit time: 60 seconds
! Maximum entry time: 45 seconds
! Do not program “Swinger Shutdown”, “Force Arming”, “Selective Bypass”, “Group Bypass”, or “50 ms Loop
Response”
! “Abort Delay” may not exceed 45 seconds
! Program “Disable Callback Download”
! Automatic dialer may not dial a police station number that has not been dedicated for such service
! System must be tested at least weekly under AC/battery and Battery-Only conditions
! Replace the rechargeable battery at least every 5 years
! If the battery is heavily discharged, replace it or have it tested by a qualified technician
! For silent panic, connect only to UL-listed holdup devices
! All zones must be programmed for “Priority”
! Do not program any zones for “Keyswitch Arming”
! System must be serviced at least once every 3 years
! Residential Fire and Combination Residential Fire & Burglary must program “Residential Fire”
! Keypad Expansion (EZM) Zones are not to be used as fire zones
Compatible Smoke Detectors
2 Wire Smoke Detectors
Manufacturer Model Base
NAPCO FW-2 N/A
Sentrol/ESL 429C, 429CT N/A
711U, 711UT, 712U 701U,
702U,
713-5U, 713-6U N/A
721U, 721UD, 721UT 702RE,702R
U
521, 541 & 741
series N/A
722U, 722UT, 731U,
732U N/A
System
Sensor 1100, 1151, N/A
1400, 2100, N/A
2100T, 2100S,
2100TS N/A
2100AT, 2151, N/A
2400, 2400TH N/A
Note: Voltage Rating: 8.5–13.3 VDC
Maximum Number of Detectors per zone:
10
4 Wire Smoke Detectors
Manufacturer Model Base
Gentex 812, 812T, 812P,
812PT, N/A
812PH, 8120, 8120T, N/A
8120P, 8120PTY, 8120-
PH N/A
Hochiki SLG-12 w/YBC-RL4-RA
base N/A
NAPCO FW-4 N/A
Sentrol/ESL 445AT, 445C, 445CT,
445CR, N/A
445CT, 445CR, 445CRT N/A
449 series N/A
System
Sensor 1112, 2112, 21112T, 211TSRB N/A
1412TH, 2412TH,
2312/24T, 1412, N/A
Note: Subtract total smoke-detector alarm
current from available standby current.
UL Compatible Smoke Detectors (Providing UL Recognition or Listing)
Note: Any normally-open devices that do not require power from the control panel, such as pull stations,
waterflow and thermostats may be used if acceptable to the Authority Having Jurisdiction.

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 9
INSTALLATION
INSTALLATION
MOUNTING
Control Panel
Choose a mounting location accessible to (a) a continuously-powered AC source, (b) system ground, a steel or copper
ground rod, ideally no further away than 10 feet, and (c) telephone lines (keep telephone wiring away from keypad wires).
Remove appropriate knockouts for cables. Place the control panel at a convenient viewing height and mark the mounting
holes. Attach the enclosure using screws suitable for the mounting surface.
Grounding
Connect the control-panel grounding screw through a No. 16 AWG. or larger wire to a long steel or copper ground rod
driven deeply into the earth. Do not use a gas pipe, plastic pipe or ac ground connections. Make the run as short and
direct as possible, without any sharp bends in the wire.
Tamper Switches
Tamper switches may be installed to prevent opening of the control-panel door or removal of the cabinet from the wall.
Ideally, tamper switches should be connected to a zone that is active at all times, thus it may be necessary to program
that zone as a 24-Hour Zone or Day Zone. When used on a normally-open zone, normally-closed tamper switches (open
when set) should be wired in parallel. On a normally-closed zone, install Napco TPS-2 normally-open tamper switches
(closed when set) in series.
There are two places in the cabinet to mount tamper switches: (1) To prevent cabinet removal from the wall, there are
three mounting holes on the left side of the cabinet, another hole on the back that allows the switch button to contact the
wall. (2) To prevent opening the cabinet door, there are three mounting holes on the right side of the cabinet. When
mounted, the switch button should contact the inside of the door. Be sure to alert the user that opening the enclosure
door will cause a tamper alarm. Note: Each tamper switch is furnished with three machine screws for mounting, and one
self-tapping screw. The sole purpose of the self-tapping screw is to tap the holes for the machine screws; it may be
discarded after use.
Keypad
A keypad should be located near each exit/entry door. The keypad features a handy pull-up reference label. Before
mounting the keypad onto the wall, push the Sliding Label Plate (with label and felt backing affixed and handle facing
forward) down the guides at the rear of the keypad until it snaps into place. Once installed, the Sliding Label Plate cannot
be removed without first removing the keypad from the wall. Note: (1) The keypad fire and panic keys should not be
considered a substitute for a listed manual initiating device, such as a pull box. (2) Each GEM-RP1CAe2 includes
provisions for four additional zones. See ADDING EXPANSION ZONES.
If installing onto a double-gang box, insert mounting screws through the two vertical elongated holes on the left side of
the case and into the box. If the box is visible when viewed from the front, adjust the keypad vertically and tighten the
screws. Then, using hardware suitable for the mounting surface, add one or two screws at the right side of the keypad
case directly into the wall to ensure a secure installation. Note: Do not overtighten the screws! Uneven walls may cause
the keypad case to distort.
CAUTION: This equipment generates and uses radio-frequency energy. If not installed using conventional installation
practices for RF devices, it may cause interference to radio and television reception. It has been tested and found to
comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed
to provide reasonable protection against such interference. However, there is no guarantee that interference will not
occur in a particular installation. If it has been found to cause interference to radio or television reception, which can be
determined by removing and reapplying AC and battery power to the equipment, the installer should try to correct the
interference by one or more of the following measures: reorient the receiving antenna; connect the power transformer to
a different outlet so that the control panel and receiver are on different branch circuits; relocate the control panel with
respect to the receiver.

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 10
WIRING
Wire keypad(s), zones, expansion zone modules and output devices as shown on the Wiring Diagram. Note that the
Wiring Diagram contains important information not available elsewhere in this manual.
Adding Expansion Zones
GEM-P3200 Series control panels will handle up to 8 zones as is, however this number may be increased to as many as
32 programmable zones using optional expansion zone modules (EZMs).
WIRELESS SYSTEMS (NOT EVALUATED BY U.L.)
With the addition of at least one GEM-RECV series receiver, the GEM-P3200 will support up to 48 wireless transmitters.
The panel can accommodate one to four receivers within the premises, responding to the one with the stronger
transmitter signal. If any transmitters are selected for the default program, a GEM-RECV receiver will automatically be
programmed.
The keypad can display the status of any transmitter, indicating the condition of the zone (normal or open) and transmitter
troubles (low battery, tamper or supervisory failure), and signal strength of the last transmission. A receiver failure will be
indicated by “E06-NN” (“no response”, with NN representing the receiver number).
TYPICAL RESIDENTIAL FIRE INSTALLATION (WHERE PERMITTED BY
LOCAL CODES)
At least one smoke detector should be installed directly outside
each sleeping area. If there is more than one floor, additional
smoke detectors should be installed on each level, including the
basement. The living-area and basement smoke detectors should
be installed near the stairway of the next upper level.
For increased protection, additional detectors should be installed
in areas other than those required, such as the dining room,
bedrooms, utility room, furnace room, and hallways. Heat
detectors, rather than smoke detectors, are recommended in
kitchens, attics, and garages due to conditions that may result in
false alarms and improper operation. Large areas and areas with
partitions, ceiling beams, doorways, and open joists will require
additional detectors.
Refer to NFPA Standard No. 74 (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269) for
additional information, including proper mounting of detectors.
TYPICAL PARTITIONED INSTALLATION
Described and illustrated here are an example of a partitioned system
with common-area protection of the control-panel room. This system
meets UL requirements for a partitioned installation.
! Both areas must be owned and managed by the same person(s).
! Both areas must be part of one building at one street address.
! The control panel and all wiring protecting each partitioned area must be
confined to the respective area and may not encroach upon the other area. This
requires that the control panel room have redundant protection; that is (a)
multiple sets of door contacts, each wired to a separate zone and (b) one of
those zones programmed for each area. In order to gain access to this protected
area without causing an alarm, both partitions must be disarmed. In lieu of
redundant protection, 24-Hour Zones may be used. Any zone protecting the
control panel and transformer may not be programmed for bypass.
The sounding device must be placed such that the bell test can be heard by all
partitions. Note: NFPA 74 (Household Fire Warning Equipment) requires that a
fire alarm audible device be installed indoors. The User Program Code is not to be given to anyone except the authority responsible
for all partitions.
CAUTION: Do not run telephone wiring near speaker wires; do not run keypad wiring with loop wiring.
INSTALLATION

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 11
UL COMMERCIAL-BURGLARY INSTALLATIONS (PENDING)
The GEM-P3200M can be used as part of a UL Central
Station Grade C, B, or A installation. Normally, a digital
communicator is classified as Grade C and may be
classified Grade B if used with the specified Grade-A Local
bell and bell housing. A UL Central Station Grade-A
installation requires the use of a Napco RM3008 Relay
Board and Ademco 7720 Radio System. Refer to the
installation instructions furnished with each component for
respective installation requirements.
For a UL Commercial Grade-A Police Station Connection,
refer to GRADE-A LOCAL MERCANTILE
INSTALLATIONS, which follows. Use the M278 Line-
Reversal Monitor to provide basic line security; refer to the
instructions accompanying the M278 for other installation
requirements.
For UL Commercial safe and vault applications, use a
UL-listed shock sensor suitable for metal enclosures.
Install tamper switches on front and rear of control-panel
enclosure.
Grade-A Local Mercantile Installations
A Grade-A Local Mercantile installation must use at least
a 6.0AH standby battery. Programming must include Auto
Bell Test on Arming. Trouble on Night Open may not be
programmed for any zone.
The minimum requirements for a listed Grade-A Local
system include:
! Low-Battery Annunciation.
! An Ademco AB-12 Bell and Box (12-volt).
! Program Auto Bell Test on Arming.
! a maximum Entrance and Exit Delay of 60 seconds.
Interfacing to the Ademco 7720 Long-Range Wireless System
The RM3008 may be used to interface the GEM-P3200M control panel to the Ademco 7720 transmitter in order to meet
UL Central Station Grade-A or Grade-B requirements by using a digital communicator combined with one-way wireless.
(Normally, a digital communicator is Grade C, and may be Grade B if the specified Grade-A local bell is used.) Refer to
the wiring diagram which follows, and to the instructions furnished with the Napco and Ademco equipment for further
information concerning the DACT, listed compatible receiver and formats, Grade-A local bell and bell housing. Enable
Line Fault Test must be programmed.
Central Station Grade-B Requirements (Pending)
Wiring to the Ademco 7720 transmitter must be enclosed in rigid conduit when outside walls, or in flexible conduit when
inside walls or above ceilings, for the entire length up to the transmitter room. The transmitter room must be protected by
a UL listed intrusion detection unit that is connected to one of the input channels of the Ademco 7720. Relays must be
programmed to trip the Ademco 7720 for alarms on all protective circuits, including tampers, telco phone failure, 24-hour
test timer, transmitter low battery and ac loss. (See PCD3000 External Relay Control screen.) One zone on the
GEM-P3200M, programmed as a 24-Hour Zone, must supervise the radio.
Central Station Grade-A Requirements (Pending)
In addition to Grade-B Requirements (above), one relay on the RM3008 must be programmed to trip the Ademco 7720
when the telephone line fails. Daily openings and closings are required to be transmitted by the Napco panel along with
the 24-hour DACT test signal and DACT trouble conditions.
INSTALLATION

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 12
INSTALLATION
TESTING THE SYSTEM
After installation is completed, test the system as follows.
! 1. Call the central station to inform them of the test.
! 2. Initiate an alarm, preferably on a zone that activates a steady siren, and verify proper signaling.
! 3. Wait 5 minutes.
! 4. Call the central station to confirm their receipt of a good transmission.
Note: Be sure to test all enabled keypad panics.
Signal Strength Testing/Wireless Systems
To test the operation of wireless transmitters, proceed as follows. (Note: Wireless systems have not been investigated by
UL.)
! Fault a point of each transmitter to be tested by faulting the zone.
The transmitter signal strength can be displayed using the DISPLAY RF XMITTER STAT function. Enter a Level 3 User
Code or enter the Dealer Code, press the Abutton and answer NO until “DISPLAY RF XMITTER STAT” is displayed. Press
YES (Ebutton) and the Wireless Signal Strength of the wireless zone will be displayed. The Wireless Signal
Strength will be displayed from 1 to 10 with 10 being the strongest signal and any signal under 3 as unacceptable. Except
in the Fault-Find Mode, signal strengths less than 3 will be entered into the system log. Press NEXT (Ebutton) to
step the next zone.
The last received signal strength for each transmission is always stored in memory and can viewed at any time using this
procedure. Signal strength can also be viewed through the PCD3000 Status Screen.

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 13
WIRING CONNECTIONS
WIRING CONNECTIONS
AUXILIARY ALARM OUTPUT
Auxiliary Output can be activated depending on the programming options selected (see
GEM-P3200 Programming Instructions). Connect the device controlled by the programmable
output between terminal 8 (+) and terminal 14 (-). A programming option “Aux. Output Chirp on
Key-fob Arming” is available. If selected, an external siren driver can be connected to these
terminals.
TRANSFORMER
Connect a 16.5 VAC Transformer to Terminals 1 and 2, using a wire of #18 AWG. or
less at a distance of 15 ft. or less from the control panel. NOTE: Do not connect to a
switched outlet.
AC IN, 16.5V/60HZ VIA
TRF11 OR TRF14
CLASS 2 TRANSFORMER
DO NOT CONNECT TO
SWITCHED OUTLET
1
2
BATTERY
The RED (+) and BLACK (-) flying leads must be connected to
a 12VDC 4, 6 or 7 AH Rechargeable Battery, to serve as
backup power in the event of AC Power Failure. NOTE: To
calculate the available standby time refer to the Standby-
Battery Calculation Worksheet at the back of this manual.
4 AH, 6 AH OR 7 AH
RECHARGEABLE
BATTERY 12 VDC
Connect the alarm sounding devices (self-contained sirens, speakers or a mechanical bells) to
terminals 5 (+) and 14 (-). Any self-contained siren requiring a 12 VDC input can be connected.
When connecting a mechanical bell, it must be supervised using a 2.2k Ohm resistor. To
connect 8 Ohm Speakers use a Siren Driver with the proper polarity observed. NOTE: Refer to
the Wiring Diagram for alarm current specification, bell supervision and burglary output relay.
SIREN/BELL BURG/FIRE ALARM OUTPUT

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 14
EARTH GROUND
NOTE: Do not use a gas pipe, plastic
pipe or AC ground connections.
Connect the control panel EARTH GROUND screw through a No. 16 AWG.
or larger wire to a metal cold-water pipe. Do not use a gas pipe, plastic pipe
or AC ground connections. Also, connect the circuit board to the metal
enclosure. Connect a wire with a ground lug crimped or soldered onto one
end of the EARTH GROUND screw to the cabinet. NOTE: Grounding
connections should avoid bends in the grounding wire whenever possible.
WIRING CONNECTIONS
REMOTE BUS
AUXILIARY POWER
Connect the auxiliary devices (motion detectors, glass breaks, etc.) to Terminals 13 and 14.
Auxiliary Power provides a filtered 12 VDC nominal output which is used for powering auxiliary
devices. NOTE: To calculate the available standby time refer to the Standby-Battery Calculation
Worksheet at the back of this manual.
13
(+)
14
(-)
AUX POWER
Connect the available devices as shown above to the remote bus terminals (9, 10, 11 & 12). Observe the correct color
wire connections. When connecting a keypads, first configure them accordingly (refer to the Keypad Configuration Mode
at the back of this manual). Keypads should be located near every exit/entry door. Up to seven keypads may be
connected if the longest cable run from the panel, to the farthest keypad (daisy chained or home-run) is less than 1000
feet. The maximum distance for seven keypads is 300 feet using 22 AWG. wire. NOTE: When running keypad wire, avoid
wiring parallel to other types of wiring that can cause electrical interference.
R
COMPUTERIZED SECURITY SYSTEM
GEMINI
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
DE
F
G
NEXT/YES
PRIOR/NO
AREA
GEM-RP1CAe2
(2 LINE LCD KEYPAD)
NOTE: Refer to the EZM Installation Instructions for specific
wiring information.
AVAILABLE DEVICES
1. KEYPADS: GEM-RP1CAe2, GEM-RP2ASe2 & GEM-RP3DGTL
2. X-10 INTERFACE: GEM-X10
3. WIRED ZONE EXPANDER: GEM-EZM4 & GEM-EZM8
4. WIRELESS RECEIVERS: GEM-RECV8, GEM-RECV16 & GEM-RECV96
5. RELAY MODULE: RM3008
6. VOICE INTERFACE: GEM-EVA 1
7. TELEPHONE INTERFACE: WIZARD IIe

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 15
WIRING CONNECTIONS
BASIC ZONE CONFIGURATION
The basic zone configuration for the GEM-P3200 is 8 zones. Connect as shown above to terminals 16-27. Normally
Closed (N.C.) devices may be wired in series or Normally Open (N.O.) devices may be wired in parallel. Use the 2.2K Ohm
end-of-line (E.O.L.) resistor in each zone, if selected in programming (refer to the GEM-P3200 Programming Instructions).
Zones 1-8 can be selected for a “Fast Loop Response (10ms or 50 ms)” or a “Normal Loop Response (750 ms)”. Other
zone options include Zone Type (Entry/Exit, Interior, 24 Hour Protection, Trouble and Fire), Instant, Chime, Area Selection
and Relay Output selection.
RESET OUTPUT
Reset Output can be activated depending on the programming options selected (see GEM-
P3200 Programming Instructions). Connect the device controlled by the programmable output
between terminal 15 (+) and terminal 14 (-).
15
RESET
OUTPUT
EXPANDED ZONE CONFIGURATION
The GEM-P3200 Control Panel may be expanded up to 32 zones. This may be accomplished by adding 24 zones to the
basic 8 zone configuration. Hardwired zone expanders include: GEM-EZM4 (4 additonal zones per module), GEM-EZM8
(8 additional zones per module) and GEM-RP1CAe2 Keypad (4 additional zones per keypad). Wireless zone expanders
including the GEM-RECV8 (8 additional zones per receiver), GEM-RECV16 (16 additional zones per receiver) and
GEM-RECV96 (88 additional zones per receiver) may be used to increase the maximum number of zones top 48. Wireless
transmitters include: GEM-TRANS2, GEM-KEYF, GEM-SMK, GEM-PIR, GEM-DT and GEM-GB.
Additional Zones are numbered 9-32.
R
COMPUTERIZED SECURITY SYSTEM
GEMINI
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
DE
F
G
NEXT/YES
PRIOR /NO
AREA
GEM-RP1CAe2
(2 LINE LCD KEYPAD)

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 16
WIRING CONNECTIONS
4-WIRE SMOKE DETECTORS
4-WIRE SMOKE DETECTOR WIRING
The GEM-P3200 can use conventional 12 VDC 4-wire smoke detectors. To use them, the
select fire zone programming option and do not select 2-wire smoke detector
programming option for the desired fire zone (refer to the GEM-P3200 Programming
Instructions). Set JP7 to the BURG position as shown, if zones 7 or 8 are to be used.
Four wire smoke detectors may be connected to any programmed fire zone (1-8) as
shown, within the panel. If external EZMs are used for zones 9-32, then 4-wire smoke
detectors may be connected to any programmed fire zones (9-32).
Power must be obtained from terminal 28 (+) and 29 (-). If Fire Alarm Verification is
desired to reset the smoke detectors, select this option for the desired fire zone.
NOTE: Do not program Fire Alarm Verification in California
2-WIRE SMOKE
DETECTOR WIRING
Two-wire smoke detectors may be connected to control panel zones 7 and 8, which
are configured for 2 wire fire through the JP7 jumper settings. To enable, program
the zone(s) as Fire Zones, enable 2-Wire Fire (refer to the GEM-P3200
Programming Instructions) and set JP7 to the position as shown. Connect the
2-wire smoke detectors as shown.
If Fire Alarm Verification is desired to reset the smoke detectors, select this option
for the desired fire zone (zone 7 or 8).
NOTE: Do not program Fire Alarm Verification in California
2-WIRE SMOKE DETECTORS
26 27 28
(-)
29 28

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 17
WIRING CONNECTIONS
Connect the Model 368 Cord as follows: 30 (RED = Telco Tip), 31 (GREEN = Telco Ring), 32 (GRAY = Home Tip)
and 33 (BROWN = Home Ring). Insert the modular plug into an approved USOCRJ31X jack (or a CA31A jack for
Canadian installations). The Telco Line is used by the control panel to dial the central station and for downloading.
This line should not be connected to party lines or coin operated telephones. If connected to a line with call waiting,
then call waiting interrupt numbers must be programmed into the CS Telephone Numbers (refer to the GEM-P9600
Programming Instructions).
Model 368 Cord
TELEPHONE LINES
30 31 32 33

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 18
KEYPAD CONFIGURATION MODE
This section will focus on configuring the GEM-RP1CAe2, GEM-RP2ASe2 and GEM-RP3DGTL Keypads. If there is more than one
keypad in the system, only Keypad No. 1 may be used for programming.
KEYPAD INSTALLATION
Three types of keypads may be used with the GEM-P3200: the GEM-RP1CAe2, the GEM-RP2ASe2 and the GEM-RP3DGTL. Each
must be assigned an address number (1–7) and each requires its own configuration procedure (see CONFIGURING THE KEYPADS,
which follows, and DIRECT ADDRESS KEYPAD AREA OPTIONS). At least 1 keypad must be used; only 1 is required for a single-
area Commercial Burglary installation.
GEM-RP1CAe2 - is a 2-line combination fire/burglary/access keypad capable of supporting 4 EZM zones and a PGM output.
A GEM-RP1CAe2 is recommended for use as Keypad #1.
GEM-RP2ASe2 - is a fixed English Alpha Symbol LCD keypad combining several preset LCD words with a limited message line.
NOTE: Due to space constraints, available messages are abbreviated and will scroll automatically.
GEM-RP3DGTL - is a Digital Display numeric keypad combining a dual seven segment display with LED indicators to convey system
status.
CONFIGURING THE KEYPADS
A total of up to 15 keypads may be connected to the panel. GEM-RP1CAe2, GEM-RP2ASe2 and GEM-RP3DGTL
keypads may be intermixed but require different configuration procedures, as described in the following paragraphs.
However, Keypads 8 - 15 may only be GEM-RP1CAe2 model.
Configuring the GEM-RP1CAe2 Keypad
Each GEM-RP1CAe2 keypad must be configured for (a) keypad tactile beep; (b) entry sounder; (c)
keypad address; (d) compatibility number; (e) EZM address; and (f) zone response.
To enter the GEM-RP1CAe2 Configuration Mode:
1. Move jumper JP5 (located at the upper-right corner of the control panel board) from Pins 1-2 (top two) to Pins
2-3 (bottom two). NOTE: See Wiring Diagram.
2. After about 15 seconds, the display will read “XX OUT OF SYSTEM”, where XX indicates the keypad address.
3. Press 11123 Aand proceed as follows. (Repeat the following procedure for all keypads.)
Keypad Tactile Beep
Upon entering the Keypad Configuration Mode, “KEYPAD BEEP ON” will be displayed,
indicating that the tactile beep, which sounds when any button is pressed, is on. To
turn off the tactile beep, press the Jbutton (the Jbutton will toggle the tactile beep
on and off).
Press the Abutton to continue or press the Cbutton to exit.
Entry Sounder
To turn off the keypad sounder during entry time, press the Jbutton (the Jbutton
will toggle the tactile beep on and off). Press the Abutton to continue or press
the Cbutton to exit.
Keypad Address
If more than one keypad is installed, each must be assigned a unique
keypad address (that is, no two keypads may be numbered alike):
! keypads must be numbered consecutively (missing numbers are not permitted)
! only Keypad No. 1 may be used for programming.
To assign the keypad number, proceed as follows:
1. Enter the assigned keypad number 01–15, then press the Jbutton to save. A valid number will be acknowledged by a short
beep; an invalid number will be rejected by a long beep.
2. Press the Abutton to continue or press the Cbutton to exit.
KEYPAD BEEP
ON
ENTRY SOUNDER
ON
KEYPAD ADDRESS
01
NORMAL
KEYPAD
CONFIGURE
KEYPAD CONFIGURATION
R
COMPUTER IZED SECUR ITY SYSTEM
GEMINI
ARMED
STATUS
SYSTEM ARMED
01/01/97 12:00AM
12
4
3
56
7890
A
B
C
DE
F
G
NEXT/YES
PRIOR/NO
AREA

LNAPCO Security Systems X GEM-P3200 Installation Instructions
WI817C 08/00 ! Page 19
Compatibility Number
The compatibility number is a 4-digit security code that, if programmed into
both the control panel and each GEM-RP1CAe2 keypad, dedicates the
keypad to only that panel. That is, (a) similar keypads not having the correct
compatibility number will not operate in the system and (b) a keypad may
not be removed for use on a system with a different compatibility number. Note: (1) If assigning compatibility numbers,
record and store them in a safe place. (2) The GEM-RP2ASe2 and GEM-RP3DGTL Keypads will function with or without
a Compatibility Number.
While the compatibility number may be changed, the old number must be known in order to program the new number.
Note: If neither the control panel nor the keypad is given a compatibility number, both default to “0000” (thereby
maintaining compatibility).
To program the compatibility number, press the Abutton until “NEW COMPAT# 0000” is displayed. Enter the 4-digit
compatibility number that is programmed into the panel. Note: If the keypad had been previously programmed for a
compatibility number other than “0000”, the display would read “OLD COMPAT# XXXX”. Enter the existing number before
attempting to change it. Press the Abutton to continue or press the Cbutton to exit.
EZM Address
The keypad's internal EZM (Expansion Zone Module) may be utilized to
provide four additional wired zones. Whether used alone or in conjunction
with optional GEM-EZM series modules or other keypad EZMs, it must be
assigned a unique address (or Group number, see Keypad Programming
Workbook) similar to its keypad address. If no other EZMs are to be used,
designate the keypad as Group “01” at the “EZM ADDRESS 00” display. In multiple-EZM systems, enter an assigned group
number “01” through “06”. (Each EZM must have a unique assigned group number, starting with “01” and proceeding
consecutively.) Press the Abutton to continue or press the Cbutton to exit.
Zone Response
The normal loop response of each keypad expansion zone is 750mS,
however the response time of any zone can be reduced to 50mS as follows.
1. Of the following, circle the number(s) in parentheses associated with the
zone(s) to be changed: Zone 1=(1); Zone 2=(2); Zone 3=(4); Zone 4=(8)
2. Add up the circled numbers.
3. At the keypad, enter the sum as a two-digit number “01” through “15” on the display, then press the Jbutton.
Example. Change Zones 2, 3 and 4 to 50mS response.
1. Circle numbers for Zones 2, 3 and 4: (2), (4) and (8).
2. Add up the circled numbers: 2 + 4 + 8 = 14.
3. Enter “14” at the keypad, then press the Jbutton.
Press the Abutton to continue or press the Cbutton to exit.
Program Control Message
The Access-Control message normally displays “**ENTER NOW**” however
this display may be changed to any of the following messages:
Press the Abutton to continue (the display will loop back through selections,
for changes) or press the Cbutton to exit the Keypad Configuration Mode
(display will read “01 OUT OF SYSTEM”). Then replace Jumper JP5 across Pins 1–2
(top two).
NEW COMPAT#
0000
KEYPAD CONFIGURATION
EZM ADDRESS
01
ZONE RESPONSE
00
PROG CONTROL
MESSAGE# 1 ENTRY MESSAGE
0“**ENTER NOW**” (Default)
1“DOOR CONTROL”
2“GATE CONTROL”
3“LIGHT CONTROL”
4“CONTROL #1”
5“CONTROL #2”
6“CONTROL #3”

XGEM-P3200 Installation Instructions LNAPCO Security Systems
WI817C 08/00
!Page 20
Configuring the GEM-RP2ASe2 and GEM-RP3DGTL Keypad
Up to 7 GEM-RP2ASe2 and/or GEM-RP3DGTL keypads may be connected to the panel (Keypads 1–7). Each must be
configured for a keypad address. In addition, the keypad may be configured to disable (a) touchpad backlight; (b) LCD
backlight; and (c) entry sounder. Keypads are configured by the proper selection of jumpers. Refer to the label on the
circuit board inulation paper for jumper locations and a summary of settings.
KEYPAD ADDRESS
If more than one keypad is installed:
! Each must be assigned a unique address (that is, no two keypads may be
numbered alike).
! Keypads must be addressed consecutively (that is, missing numbers are not
permitted).
! Only Keypad No. 1 may be used for programming. (However, for ease of
programming, it is recommended that a GEM-RP1CAe2 be selected as Keypad
#1.)
Assign the keypad address number by selecting Jumpers J1–3 in
accordance with the table at left.
*Note: (1) Keypads are factory supplied with no jumpers installed and a as
such are automatically configured as Keypad No. 1. (2) Only one keypad
in the system may be configured as Keypad No. 1, otherwise none will
function.
TOUCHPAD BACK LIGHT
Cut Jumper A to disable touch pad backlighting to conserve 11mA standby current.
LCD BACKLIGHT
Cut Jumper B to disable LCD backlighting.
DISABLE SOUNDER
Cut Jumper C to disable the sounder. (Do not disable in UL applications.)
KEYPAD
NUMBER
1
2
3
4
5
6
7
123
OFF or
ON*
OFF OFF
OFF ON OFF
ON ON OFF
OFF OFF OFF
ON OFF ON
OFF ON ON
ON ON ON
KEYPAD NUMBER
PARK
STORE SPARE
JUMPER AT THIS
POSITION
NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: [phone]
For direct line to Technical Service, call toll free: [phone]
Internet: http://www.napcosecurity.com
KEYPAD CONFIGURATION