Satel Integra Series User manual

Alarm Control Panel Firmware version 1.08
GDAŃSK
integra_u_en 08/10
USER
MANUAL

WARNING
In order to avoid any operational problems with the control panel, it is recommended that you
become familiar with this manual before you start using the equipment.
Making any construction changes or unauthorized repairs is prohibited. This applies, in
particular, to modification of assemblies and components. Maintenance and/or repair
operations should be performed by authorized personnel (i.e. the installer or factory service).
The INTEGRA 24, INTEGRA 32, INTEGRA 64 and INTEGRA 128 control panel should be
connected to analog lines only. Connecting its telephone circuit to a digital network (e.g.
ISDN) may cause damage to the equipment. In case of changing the analog line to the digital
one, it is necessary to contact the alarm system installer.
Pay special attention if the telephone line used by the control panel is frequently busy and/or
failures are reported concerning the line and/or monitoring. Report such situations to the
alarm system installer immediately.
CAUTION!
The alarm system is fitted with a battery. After expiry of its lifetime, the battery must not be
thrown away, but disposed of as required by the existing regulations (European Directives
91/157/EEC and 93/86/EEC).
The latest EC declaration of conformity and product approval certificates
are available for downloading on website www.satel.pl
The INTEGRA alarm control panels INTEGRA 24, INTEGRA 32, INTEGRA 64 and
INTEGRA 128 meet requirements as per CLC/TS 50131-3, Grade 3, and have been certified
by Det Norske Veritas Certification AS, Norway.
Environmental class of the INTEGRA series control panels: II.

INTEGRA SATEL 1
New features in firmware versions 1.07 and 1.08
System operation The new INT-CR proximity card arm/disarm device enables arming /
disarming and alarm clearing in many partitions by means of proximity
cards, keyfobs and other passive transponders.
Users The installer can define a minimum length of codes used in the
system.
New right: ZONE ISOLATION.
Data entering A new, more intuitive way of entering hexadecimal values and names.
Arming /
disarming with 2
codes
The installer can configure the system so that the validity period of the
first code in the partition is always 60 seconds (in such a case, the
user does not program any validity period for the first code).
Zone bypasses The zones can be permanently bypassed (isolated) i.e. they will not be
unbypassed on disarming the partition they belong to.
User functions The ZONE BYPASSES function has taken on the role of submenu
offering the following functions:
– INHIBIT
– ISOLATE
The PERMANENT DLOADXACCESS option has been added to the
CHANGE OPTIONS submenu.

User Manual INTEGRA2
CONTENTS
1. GENERAL............................................................................................................................4
2. ABOUT THIS MANUAL............................................................................................................4
3. TECHNICAL RELIABILITY OF THE ALARM SYSTEM......................................................................4
4. ALARM SYSTEM OPERATING COSTS .......................................................................................5
5. INTEGRA CONTROL PANEL .................................................................................................5
5.1 BASIC FUNCTIONS OF THE CONTROL PANEL....................................................................................5
5.2 CONTROL PANEL PERFORMANCE ...................................................................................................6
6. OPERATION OF INTEGRA CONTROL PANEL ..........................................................................6
6.1 LCD KEYPADS..............................................................................................................................8
6.1.1 Keypads with mechanical keys.........................................................................................................8
Display................................................................................................................................................. 10
Keys..................................................................................................................................................... 10
LED indicators ..................................................................................................................................... 10
6.1.2 Audible signals in keypads .............................................................................................................11
6.1.3 Using LCD keypad..........................................................................................................................12
6.1.4 Entering data by means of the LCD keypad...................................................................................13
Selection from the single-choice list.................................................................................................... 14
Selection from the multiple-choice list in the text mode ...................................................................... 14
Selection from the multiple-choice list in the graphic mode ................................................................ 14
Entering decimal values ...................................................................................................................... 14
Entering names ................................................................................................................................... 14
6.1.5 Reading alarm source name ..........................................................................................................15
6.1.6 Proximity card reader (INT-KLCDR-GR/INT-KLCDR-BL only).......................................................15
6.2 PARTITION KEYPADS ...................................................................................................................16
6.3 MULTIFUNCTIONAL KEYPAD WITH PROXIMITY CARD READER..........................................................20
6.3.1 Operation in partition keypad mode (INT-S/SK).............................................................................20
6.3.2 Operation in partition keypad mode with proximity card reader (INT-SCR) ...................................21
6.3.3 Operation in entry keypad mode (INT-ENT)...................................................................................23
6.4 CODE LOCKS ..............................................................................................................................24
6.5 PROXIMITY CARD AND DALLAS CHIP READER..............................................................................26
6.6 CODES AND USERS .....................................................................................................................26
6.7 PREFIXES ...................................................................................................................................27
6.8 PROXIMITY CARDS/DALLAS CHIPS..............................................................................................28
6.8.1 Adding proximity card / DALLAS chip by means of LCD keypad...................................................28
6.8.2 Adding proximity card / DALLAS chip by means of DLOADX program ...........................................28
6.8.3 Adding proximity card / DALLAS chip by means of GUARDX program...........................................28
6.8.4 Deleting cards/DALLAS chips by means of LCD keypad...............................................................29
6.8.5 Deleting proximity card / DALLAS chip by means of DLOADX program .........................................29
6.8.6 Deleting proximity card / DALLAS chip by means of GUARDX program.........................................29
6.9 APT-100 KEYFOBS .....................................................................................................................29
6.9.1 Adding keyfob by means of LCD keypad .......................................................................................30
Entering the serial number manually................................................................................................... 30
Reading the serial number during transmission.................................................................................. 31
6.9.2 Adding keyfob by means of DLOADX program................................................................................31
Entering the serial number manually................................................................................................... 31
Reading serial number during transmission........................................................................................ 31
6.9.3 Removing keyfob by means of LCD keypad ..................................................................................32
6.9.4 Removing keyfob by means of DLOADX program...........................................................................32
6.9.5 Assigning zones to buttons by means of LCD keypad ...................................................................32
6.9.6 Assigning zones to buttons by means of DLOADX program............................................................32
6.9.7 Assigning the outputs to the LEDs by means of LCD keypad........................................................33
6.9.8 Assigning the outputs to the LEDs by means of DLOADX program ................................................33
6.9.9 Configuring event generation rules by means of LCD keypad.......................................................33
6.9.10 Configuring event generation rules by means of DLOADX program................................................34

INTEGRA SATEL 3
6.10 SYSTEM ARMED MODE................................................................................................................ 34
6.11 ALARMS ..................................................................................................................................... 37
6.12 ALARM MESSAGING BY TELEPHONE............................................................................................. 37
6.13 ANSWERING PHONE CALLS ......................................................................................................... 38
6.14 OTHER FUNCTIONS USING TELEPHONE LINE................................................................................. 39
6.15 SMS CONTROL ONLY INTEGRA 128-WRL................................................................................. 40
7. USER FUNCTIONS ............................................................................................................. 40
7.1 MAIN MENU ................................................................................................................................40
7.1.1 User function menu ........................................................................................................................40
7.2 DESCRIPTION OF USER FUNCTIONS ............................................................................................. 43
View cleared alarms .................................................................................................................................44
System reset.............................................................................................................................................44
Disarm ......................................................................................................................................................44
Clear alarm ...............................................................................................................................................44
Clear other alarms ....................................................................................................................................44
Abort voice messaging .............................................................................................................................44
Arm ...........................................................................................................................................................44
Arm (2 codes) ...........................................................................................................................................44
Disarm (2codes) .......................................................................................................................................45
Defer auto-arming.....................................................................................................................................45
Set auto-arming delay ..............................................................................................................................45
Arming mode ............................................................................................................................................46
Cancel 1st code ........................................................................................................................................46
Change own code.....................................................................................................................................46
Change prefix ...........................................................................................................................................47
Masters .....................................................................................................................................................47
Users ........................................................................................................................................................47
Zone bypasses .........................................................................................................................................50
Inhibit....................................................................................................................................................50
Isolate...................................................................................................................................................51
Set time.....................................................................................................................................................51
Troubles....................................................................................................................................................51
Events.......................................................................................................................................................52
Reset zones..............................................................................................................................................53
Clear latched outputs................................................................................................................................53
Fire door opening finished ........................................................................................................................53
Change options.........................................................................................................................................53
Tests .........................................................................................................................................................55
Service access..........................................................................................................................................57
Open door.................................................................................................................................................57
Outputs control .........................................................................................................................................57
Controlling the MONO SWITCH type of output.......................................................................................58
Controlling the BI SWITCH type of output...............................................................................................58
Controlling the REMOTE SWITCH type of outputs ....................................................................................58
Controlling the SHUTTER UP and SHUTTER DOWN type of outputs..........................................................58
Service mode............................................................................................................................................59
Take SM over ...........................................................................................................................................59
Downloading.............................................................................................................................................59
8. CONFORMANCE TO CLC/TS 50131-3 REQUIREMENTS ......................................................... 60
9. APPENDIX A...................................................................................................................... 61
10. APPENDIX B...................................................................................................................... 63
11. APPENDIX C ..................................................................................................................... 64
12. BRIEF DESCRIPTION OF OPERATING THE SYSTEM FROM KEYPAD ............................................ 69
13. HISTORY OF THE MANUAL UPDATES..................................................................................... 70

User Manual INTEGRA4
1. GENERAL
Thank you for choosing the product offered by the SATEL Company. High quality, large
number of functions and simple operation are the main advantages of our alarm control
panel. Wishing you full satisfaction with the choice you made, we are always ready to provide
you with professional assistance and information on our products. Please note that, besides
the control panels, SATEL manufactures many other components of alarm systems. Detailed
information on our full offer can be found nationwide at retail dealers offering our products, on
website www.satel.eu.
2. ABOUT THIS MANUAL
This Manual allows you to familiarize yourself with the basic operation of modules designed
to control the operation of alarm systems based on the INTEGRA control panels and with the
functions performed by these panels. The INTEGRA includes alarm control panels:
INTEGRA 24, INTEGRA 32, INTEGRA 64 and INTEGRA 128 and INTEGRA 128-WRL.
The part OPERATION OF INTEGRA CONTROL PANEL of this Manual describes the modules that
control operation of the control panel and how they should be used. It also presents some
functions related to the alarm system operation, and includes some basic information on
functioning of the system and use of the telephone line by the control panel.
The part USER FUNCTIONS of this Manual contains full specification of functions accessible
from the alphanumeric LCD keypad.
The text in this Manual contains some technical terms: for explanation please refer to
APPENDIX B at the end of this Manual.
Please read carefully the entire manual since familiarity with the control panel functions will
allow you to take full advantage of the equipment possibilities. The control panel can perform
functions that are nor related directly to monitoring. The use of all control panel functions and
the operational efficiency of the entire system depend to a large extent on its installation
method and its programming by the installer. The control panel may perform its functions in
many ways, which are defined when installing and programming the system. Therefore, you
should obtain from the installer more detailed information on how the alarm system operates
and how it should be used.
All situations in which the way of the control panel operation depends on previous installer
decisions (made at the time of programming) are additionally marked by inserting the PROG
symbol (after description of the situation).
The term "service", as used in this manual, refers to the user who takes care of the alarm
system and is authorized to use the service code. He can be installer, maintenance
technician, security guard employed for protection of the facility, etc.
3. TECHNICAL RELIABILITY OF THE ALARM SYSTEM
The alarm system is composed of technical devices whose reliability is vital for the
effectiveness of the facility protection. The elements of the alarm system are exposed to the
impact of various outside factors, including weather conditions (outside sirens), atmospheric
discharges (overhead telephone lines, power lines, outside sirens), mechanical damage
(keypads, detectors, etc.). Only routine inspection of the alarm system operation will make it
possible to keep a high level of burglary and fire protection.
The control panel is provided with a number of safeguards and auto-diagnostic functions for
testing the system reliability. If the keypad [TROUBLE] LED is lit, it indicates that the
control panel has detected a fault. You should immediately respond to such a signal,
and, if necessary, consult the installer.

INTEGRA SATEL 5
It is necessary to periodically carry out a functional test of the alarm system. Check that the
control panel responds to violation of individual detectors, that their fields of view are not
masked, that there is a reaction to opening protected windows, and that sirens and telephone
messaging work normally.
Detailed instructions on the system testing should be provided by the installer. It is
recommended that the installer carry out periodic maintenance of the alarm system, when
ordered by the user.
It is in the user's best interest to anticipate and plan beforehand appropriate procedures in
case the control panel signals an alarm condition. It is important that he should be able to
verify the alarm, determine its source on the basis of keypad information, and take
appropriate measures, e.g., to organize evacuation.
4. ALARM SYSTEM OPERATING COSTS
The main task of the control panel is signaling and efficient reporting of alarm situations and,
in the case of the monitoring function, providing the monitoring station with real-time
information about the protected facility status. Realization of these functions, based on the
use of telephone line, entails financial costs. Generally, the level of costs incurred by the
alarm system owner depends on the amount of information the control panel has to transfer
to the monitoring station. A failure of the telephone links, as well as incorrect programming of
the control panel, may to a large degree increase these costs. Such a situation is usually
related to an excessive number of connections made.
The installer can adjust functioning of the alarm system to the specific conditions and kind of
the protected site, however it is the user who should decide if his or her priority is transferring
information at any price, or, if some technical problems occur, the control panel is allowed to
skip some events, the reception of which has not been confirmed by the monitoring station.
5. INTEGRACONTROL PANEL
The INTEGRA alarm control panel is designed for the security supervision in small, medium-
size and large facilities. The supervision is not limited to protection against burglary, but it
may also include monitoring of the facility for correct functioning for 24 hours a day.
The status of the alarm system is monitored on a continuous basis. Violation of any alarm
system component triggers the so-called tamper alarm. The control panel responds to signals
from individual detectors and decides whether to signal the alarm or not. Since various
detectors may be connected to the control panel, the type and way of alarming depends on
the way of control panel programming (the control panel may respond in one way to a signal
from fire detector and in another way to a signal from a water level detector).
The control panel makes it possible to group zones and detectors connected to them into so-
called partitions, and to freely determine which partition is to be supervised (armed).
Activation of any detector from such a group (hereinafter called “zone violation") may trigger
an alarm. A great advantage of the control panel is its high flexibility in determination which
partitions may be armed at the moment.
5.1 BASIC FUNCTIONS OF THE CONTROL PANEL
•signaling burglary, attack, fire, technical and auxiliary alarms,
•monitoring – communication with the monitoring stations (real time sending detailed
information on selected events in the protected facility),
•telephone messaging on alarms – either with the use of a voice message or to a pager,

User Manual INTEGRA6
•answering phone calls (this function is protected with a separate code) which allow to:
−inform the user on the system status,
−control via telephone some of the control panel functions, which were programmed by
the service,
•real-time printout of information regarding all or selected events that have occurred in the
alarm system with the use of an external printer,
•control of access to the facilities through doors provided with electromagnetic locks,
•monitoring individual alarm system components (e.g. power supplies, batteries, wiring) for
correct operation.
5.2 CONTROL PANEL PERFORMANCE
•various means of operating and controlling the security system:
– LCD keypad,
– partition keypad,
– proximity card reader,
– 433 MHz keyfob (optionally, with INT-RX module installed),
– 868 MHz keyfob (INTEGRA 128-WRL control panel and, optionally, the other control
panels, if ACU-100 controller with firmware version 2.0 or later is connected),
– computer with DLOADX or GUARDX program installed,
– SMS message (INTEGRA 128-WRL control panel and, optionally, the other control
panels, if GSM-4S module is connected),
– Internet browser (optionally, with ETHM-1 module connected),
– cellular phone with MobileKPD application installed (optionally, with ETHM-1 module
connected),
– palmtop (PDA or MDA) with suitable application installed (optionally, with ETHM-1
module connected).
•installer defined descriptions of zones and partitions for easy identification of the alarm
source,
•visible system date and time to better check the real-time dependent functions for correct
operation,
•optional display of the status of partitions (up to 16 selected or all),
•available viewing of the alarm/trouble log (or detailed memory of all events) with textual
description of event, name of zone, module, partition or the user who operates the system,
together with accurate time of the event occurrence,
•monitoring, depending on the mainboard, of up to 8 independent alarm systems and up to
32 armed independently partitions,
•individual control of the output types of MONO SWITCH, BI SWITCH, REMOTE SWITCH,
SHUTTER UP and SHUTTER DOWN,
•dynamically changeable menu (dependent on authority level) to provide access to
a number of user functions, the selection made by accepting the suitable function from the
list shown on the LCD keypad screen,
•key shortcuts to facilitate calling frequently used functions,
•service note shown on LCD display.
6. OPERATION OF INTEGRACONTROL PANEL
The SATEL company offers a number of devices that enable operating the INTEGRA control
panel, including, first and foremost, the LCD keypads, but also keyfob transmitters, proximity

INTEGRA SATEL 7
card arm/disarm devices, partition keypads, code locks, as well as proximity card / DALLAS
chip readers.
The LCD keypads and proximity card arm/disarm devices INT-CR may be used to control
many partitions in various objects. The partition keypads control just one partition. Individual
control devices are assigned by the installer to specified partitions. The users may operate
the control panel only if they have access to partitions operated by particular keypads. This
means that the partitions assigned to the user at the stage of creating/editing a new user (see
DESCRIPTION OF USER FUNCTIONS ÆUSERS) must correspond to those operated by the
keypad. The list of partitions operated by LCD keypad or proximity card arm/disarm device
INT-CR is defined by the installer.
Example: LCD keypad controls partitions 1,2,3,4,5 and 6. The user has access to partitions
5,6,7 and 8. Hence, using this LCD keypad he can control partitions 5 and 6.
A similar principle applies to partition keypads, code locks, proximity card readers and
DALLAS chip readers. With keypads, the user can control the partitions he has access to,
and he may open the doors with code locks and proximity card/DALLAS chip readers, to
opening of which he has been authorized. The installer defines the list of users of individual
partition keypads, code locks and readers (separately for each module).
The access to the control panel control functions and the vital information on the system
status are protected with a CODE (the code is a combination of 4 to 8 digits). In systems
which require enhanced protection, it is possible to extend the code by a prefix (1 to 8 digits),
periodically changed by the object master user code.
The installer can allow some functions to be run in the keypad without entering the code
PROG. Press and hold down the keys below for 3 seconds to:
[1] – view zones status,
[4] – view partitions status,
[5] – view alarms log,
[6] – view troubles memory,
[7] – view current troubles,
[8] – switch on/off chime signal in LCD keypad,
[9] – toggle the display between standby mode and partitions state presentation mode,
Xor W– view messages about partition alarms (use the same keys to scroll through the
list of messages),
Sor T– view messages about zone alarms (use the same keys to scroll through the list of
messages),
– trigger the auxiliary alarm (for example, calling for medical aid),,
– trigger the fire alarm,
– trigger the panic alarm. The installer can determine whether the triggered panic
alarm will be an audible one (initiating the alarm signaling), or a silent one (with
no signaling).
It is recommended that the above way of calling functions be only available in
LCD keypads which are not accessible to unauthorized personnel.
If the installer has allowed for the quick arming option, the armed mode can be enabled
without entering any code, by pressing in turn the following keys:
−[0] and [#] – fully armed;
−[1] and [#] – fully armed plus zone bypasses with BYPASSED IF NO EXIT option enabled;
−[2] and [#] – armed without interior;
−[3] and [#] – armed without interior and without entry delay.

User Manual INTEGRA8
In case of the LCD keypad, the partitions indicated by the installer will be armed. In case of
the partition keypad, the partition to which the keypad is assigned will be armed. The types of
armed mode are described in section SYSTEM ARMED MODE.
Press and hold down simultaneously the Sand Tkeys for approx. 40 seconds to restart the
keypad and display the information about keypad and control panel firmware version.
6.1 LCD KEYPADS
SATEL offers a wide range of keypads which enable operating the INTEGRA alarm control
panels. The INT-KSG keypad with touch keys is described in a separate manual.
6.1.1 Keypads with mechanical keys
SATEL's portfolio includes the following mechanical keypads:
−INT-KLCD-GR/INT-KLCD-BL
−INT-KLCDR-GR / INT-KLCDR-BL
−INT-KLCDK-GR
−INT-KLCDL-GR / INT-KLCDL-BL
−INT-KLCDS-GR / INT-KLCDS-BL
These keypads differ by their size, shape and current consumption. The INT-KLCDR-GR /
INT-KLCDR-BL keypad incorporates a built-in proximity card reader. Most of the keypads are
available in two versions: with green or blue display and key backlight of the same color.
Designation of the models with green display ends with "GR" letters, and that of the models
with blue display – with "BL" letters.
Fig. 1. View of INT-KLCDR-GR keypad.

INTEGRA SATEL 9
Fig. 2. View of INT-KLCDS-GR keypad.
Fig. 3. View of INT-KLCDK-GR keypad.

User Manual INTEGRA10
Display
The keypads are provided with a 2x16 character display with backlighting. The backlighting
mode is determined by the installer. In the standby mode, the display shows the current date
and time, it can also permanently show the keypad name. The format of displayed
information is defined by the installer. The lower display line can be used to show the current
status of selected partitions (up to 16), the displayed symbols being as described in the
TESTS function.The first character in the lower line (from left) shows the status of the lowest
number partition, as selected by the installer. The following numbers show information on the
partitions in the ascending order.
The LCD display can also show important information transmitted by the service using the
so-called SERVICE MESSAGE. The displayed text can contain up to 29 characters and can be
displayed either permanently, or for a specified period of time. It can be visible either to all
users, or only to some of them after entering the access code.
Keys
Situated under the display are keys, which can be backlit (the backlighting mode being
determined by the installer), and which are used for:
•entering codes,
•moving through menu and selecting appropriate functions from the list,
•entering data for called functions.
The [#] and [ok] keys are electrically connected to each other and may be used
interchangeably. Therefore, if using the [#] key is mentioned elsewhere in the following part
of this manual, it should be understood that the [ok] key may also be used instead.
LED indicators
6 LEDs present information on the system state.
- ALARM (red) – permanent lighting of the LED indicates alarm. After expiry of the alarm
time, the blinking LED means alarm memory. The LED is going off after deletion of
alarm (see: ALARMS).
Note: The LED may not signal alarms in the armed mode if the installer has enabled the
option DO NOT SHOW ALARM IF ARMED, as required by the CLC/TS 50131-3 standard.
- TROUBLE (yellow) – blinking light indicates that a technical trouble has occurred in the
system. Emergency situations causing this LED to light up are described further in this
Manual (see DESCRIPTION OF USER FUNCTIONS ÆTROUBLES). The LED goes
temporarily off when the LCD keypad is in partially armed mode (at least one partition
accessible to the given LCD keypad is armed) or in fully armed mode (all partitions
accessible to the LCD keypad are armed) PROG. The LED is blinking until the
troubles are viewed and the trouble memory is reset (the option TROUBLE MEMORY
UNTIL REVIEW enabled) or until the trouble cause stops (the option TROUBLE MEMORY
UNTIL REVIEW disabled) PROG.
- ARMED (green) – the LED is blinking when some partitions are armed and lights
steadily when all partitions operated by the keypad are armed.
- SERVICE (green) – the LED is blinking when the control panel is in the service mode
(function only available to the user having a service code).
Note: The service mode limits normal operation of the control panel. Alarms from most
zones (except for the following types: PANIC, 24H CASH MACHINE, and 24H VIBRATION)
as well as tamper alarms are not signaled. To restore normal operation of the control
panel, you should exit the service mode, because the control panel will not
automatically return to its normal operating mode.

INTEGRA SATEL 11
- GROUP (two green LEDs) – used in graphic mode functions to indicate which data set is
currently displayed. The LEDs can show the number of zones or outputs, or indicate
the corresponding expander bus. (See: section SELECTION FROM THE MULTIPLE-CHOICE
LIST IN THE GRAPHIC MODE).
LED
INDICATION left side/upper right side/lower DESCRIPTION
OFF OFF group 1; numbers 1–32 (n)
OFF ON group 2; numbers 33–64 (32+n)
ON OFF group 3; numbers 65–96 (64+n)
ZONES/
OUTPUTS
ON ON group 4; numbers 97–128 (96+n)
OFF OFF
first expander bus
bus 1 numbers (addresses) 0-31 (DEC)
system addresses 00–1F (HEX)
EXPANDER
BUSES
OFF ON
second expander bus
bus 2 numbers (addresses 0-31 (DEC)
system addresses 20–3F (HEX)
n – number of LCD keypad field
6.1.2 Audible signals in keypads
When using the keypad the following signals, characteristic of some situations, can be heard
PROG.
•One long beep – refusal of arming - the zone, which shouldn't be violated at the time of
arming, is violated (PRIORITY option), there was a trouble with the battery, expander, or
keypad. The refusal includes all zones selected for arming. Also, warning of the system
failure - prior to arming.
•Two long beeps – unknown code/card, exit function/menu, or unavailable function.
•Three long beeps – the code is recognized, but the function called is not accessible
(for example, temporary partition blocking is activated or the user has no access to
partitions operated from the keypad).
•Two short beeps – selection accepted – entering more detailed menu level.
•Three short beeps – acknowledgement of arming or disarming.
•Four short and one long beeps – acceptance of execution of the selected function.
•Three pairs of short beeps – it is necessary to change the code (for example, another
user, when changing his code, indicated the combination of digits identical with that in the
given user code; the code validity is expiring).
Additionally, the following situations may be signaled:
•Alarm in partition – continuous beep.
•Fire alarm – long beep every second.
•Countdown of entry delay – 2 short beeps every second.
Note: The signaling of entry delay countdown by 2 short beeps refers to the LCD keypads
type INT-KLCD-GR/BL and INT-KLCDR-GR/BL with firmware in version 1.05, and to
the keypads type INT-KLCDL-GR/BL, INT-KLCDS-GR/BL and INT-KLCDK-GR with
firmware in version 6.05. In keypads with earlier firmware versions, the entry delay
countdown is signaled by short beeps every 3 seconds.
•Countdown of exit delay – long beeps every 3 seconds, completed with a series of
short beeps (for 10 seconds) and a single long beep. The way of “exit delay" signaling
informs that the countdown is ending prior to arming.

User Manual INTEGRA12
•Auto arming delay countdown (timer-controlled partitions) – a series of 7 sounds
(of diminishing length).
•Chime in LCD keypad – five short beeps – this is a response to activation of some
detectors when the zone is disarmed.
6.1.3 Using LCD keypad
Operation of the system from LCD keypad starts with entering the user CODE and pressing
the key marked [#], [ok] or [*]. The control panel response (accessible functions) after
pressing the [#] or [ok] key is different than that after pressing [*].
[CODE][#] or [CODE][ok] you get access to functions of arming/disarming type,
[CODE][*] you get access to all functions in the user menu to which the user
is authorized.
Example: When you enter your code and press [#], the control panel will make available the
functions of partition arming (provided that no partition, operated from the LCD keypad, is
already armed) or disarming (if any of partitions is armed). In the event of alarm occurrence
in the system, the control panel may cancel this alarm and provide access to the function of
partition disarming (if the user is authorized to do that). When the function of telephone
messaging is activated – the CLEAR VOICE MESSAGING function may appear in menu. When
the user has access to a single partition only, entering the code and pressing [#] results in
immediate arming or disarming (if the partition is armed).
Entering the code and pressing [*] displays the list of functions accessible from the USER
MENU. The USER MENU provides also access to the following functions: ARMING and
DISARMING (if some partitions are armed). When all partitions are armed, the function ARMING
will not be accessible.
Note: Entering a wrong code (not recognized by the panel) three times may:
−trigger an alarm PROG,
−block a keypad for 90 sec. After this time each next wrong code entering will block
the keypad PROG.
The specific feature of the control panel is the dynamic changing of the accessible menu,
dependant on the system programmed parameters, as well as on the authorization level of
the user who entered the code. The user get access only to those function in the user menu
to which he is authorized.
In order to call some functions more quickly, the user can use some SHORTCUT KEYS.
Having called the menu ([CODE][*]), type in the suitable digit or combination of digits – the
control panel will enter directly the called function.
The following user functions are assigned to the digits / combinations of digits:
1Change own code
2Users/Masters
21 New user / New master
22 Edit user / Edit master
23 Remove user / Remove master
Note: The shortcuts to the MASTERS submenu and functions available therein are only active
when the service is not authorized to edit users.
3none
4Zone bypasses
41 Inhibit
42 Isolate
5Events

INTEGRA SATEL 13
51 Selected events
52 All events
6Set time
7Troubles
8Outputs control
9Service mode
0Downloading
01 Start DWNL-RS
02 Finish DWNL-RS
03 Start DWNL-MOD.
04 Start DWNL-TEL
05 Start DWNL-CSD [only INTEGRA 128-WRL]
06 Start DWNL-GPRS [only INTEGRA 128-WRL]
07 ETHM-1 – DloadX
08 ETHM-1 – GuardX
Note: The shortcuts in the DOWNLOADING menu are available when the control panel
configuration and settings make it possible to use the selected function.
The installer can assign functions to the arrow keys to facilitate the everyday operation of
the system. These functions are called in the following way:
[CODE] S
[CODE] W
[CODE] X
[CODE] T
One of the following functions can be assigned to each arrow:
−Arming (full)
−Arming (without interior zones)
−Arming (without interior zones, without entry delay)
−Disarming
−Alarm clearing
−Zones bypassing (inhibit)
−Bypass clearing
−Output MONO ON
−Output BI switch state
−Output BI ON
−Output BI OFF
−Arming (full+bypasses)
For each of the functions the installer determines the number of partition, zone or output it
refers to. The user, who wants to perform the given function must have an appropriate
authority level and access to the selected partitions.
All user functions, which are accessible from LCD keypad, are described in section
DESCRIPTION OF USER FUNCTIONS.
6.1.4 Entering data by means of the LCD keypad
The ways of data entering can differ, depending on the function and the type of data. In most
cases, the data are saved on pressing the [#] or [ok] key. Some functions require acceptance
of the entered data by pressing an additional key (the control panel can be configured by the

User Manual INTEGRA14
installer so that pressing the key [1] will be required). The [*] key enables exiting the function
without saving the changes (which can result in quitting the user menu).
Selection from the single-choice list
Shown in the upper line of display is description of the function, and in the lower one – the
currently selected item. You can scroll through the list of items, using the direction keys: T
(down) and S(up). The Xand Wkeys are not used.
Selection from the multiple-choice list in the text mode
Shown in the upper line of display is description of the function, and in the lower one - an
item which can be selected. You can scroll through the list of items, using the direction keys:
T(down) and S(up). An additional symbol is displayed in the upper right corner:
– item not selected (e.g. partition, zone, output, etc.);
– item selected (e.g. partition, zone, output, etc.).
Press any numeric key to change the currently displayed symbol to another one.
Selection from the multiple-choice list in the graphic mode
The graphic mode is available in some functions which enable multiple selection (e.g.
selection of the partitions which are to be armed; selection of the zones which are to be
bypassed, etc.). The keypad will enter the graphic mode on pressing the Xor Wkey. The
and symbols are used to present on the display the status of items available within the
function – these can be e.g. partitions, zones, outputs, etc. ( – item not selected; – item
selected). The numbers around the display are used for numbering the items. The Xkey will
move the cursor to the right, and the Wkey – to the left . Pressing any numeric key will
change the currently displayed symbol to another one. The blank spaces (where no symbol is
displayed) are the unavailable items (e.g. partitions which cannot be armed or disarmed;
zones which cannot be bypassed, etc.) over which you cannot hover the cursor.
The display makes it possible to simultaneously present up to 32 items in the graphic mode,
while the number of items in some functions can be higher (e.g. there are 128 zones in the
system). If this is the case, go to the last available item and press the Xkey to display the
next group of 32 items. If you press the Wkey when the cursor is on the first available item,
the previous group will be displayed. The number of currently displayed group is presented
by means of LEDs designated [GROUP] (see: description of the LEDs, p. 11). To calculate
the number of items in the subsequent groups, add the number 32 (second group), 64 (third
group) or 96 (fourth group), respectively, to the number placed on the glass.
Pressing the key [0], [1] or [2] in the graphic mode will result in:
[0][0][0] - canceling the selection of any item (the symbol will be displayed in all
available positions);
[1][1][1] - selecting all available items (the symbol will be displayed in all available
positions);
[2][2][2] - reversing the selections made (the symbol will replace the symbol, and the
symbol will replace the symbol in all positions).
On pressing the Tor Skey, the keypad will return to the text mode.
Entering decimal values
Press suitable keys to enter digits. Use the Xkey to move the cursor to the right, and the W
key – to move the cursor to the left. Use the Skey to delete the character before the cursor.
Entering names
Press the particular keys until the required character appears. The characters available in the
keypad are shown in Table 1. Hold down the key to display the digit assigned to the key.

INTEGRA SATEL 15
Key Characters available after next keystroke
1 ! ? ' ` " { } $ % & @ \ ^ | # 1
2 abc2
3 def3
4 ghi4
5 jkl5
6 mno6
7 p q r s 7
8 t u v
8
9 wxyz9
0 . , : ; + - / = _ < > ( ) [ ] 0
Table 1. Characters available when entering names. The lower case letters are available
under the same keys (to change the letter case, press Tkey).
Shown on the left side in the upper line of the display is information about the letter case:
[ABC] or [abc] (it will be displayed after pressing any key and will be visible for a few seconds
after the last keystroke).
The Xkey moves the cursor to the right, and the Wkey – to the left. The Skey deletes the
character on the left side of the cursor.
6.1.5 Reading alarm source name
The installer can enable the function of displaying the name of alarm source on the LCD
keypad, without necessity of entering the code. In such a case, the partition or zone name is
displayed on the keypad screen when an alarm occurs. If there are a few alarm causes, you
may scroll through the zone names which caused the alarm, and the names of partitions
where the alarm is (or was) signaled. The Wand Xarrow keys allow viewing partition names
(if the alarm occurred in several partitions), while the Sand Tkeys allow viewing the names
of zones which caused the alarm. These names (entered by the installer) are displayed
cyclically in the lower keypad screen line, in the order corresponding to the numbers of
zones/partitions in the system. To view the names of alarm sources when the alarm signaling
is over, press and hold down the corresponding arrow key.
6.1.6 Proximity card reader (INT-KLCDR-GR/INT-KLCDR-BL only)
The INT-KLCDR-GR/INT-KLCDR-BL keypads with built-in proximity card reader make
available a few extra functions, including:
•card code readout when the card is assigned to its user (functions: NEW USER,EDIT USER),
•performance of function specified by the installer,
•registering the guard round.
The keypad can respond to the card being briefly presented to the reader or to its being
presented and held for a few seconds (approx. 3 sec.). It is also possible to perform two
consecutive functions which are assigned to bringing the card closer and holding it at the
reader. This feature makes it possible, by a single use of the card, to perform rather
complicated functions which might be time-consuming when called from the keypad.
List of functions which can be called by using the proximity card:
1. no function – no response
2. as code *– enters the user functions menu
3. as code # – calls the function of selecting partitions to be armed or disarmed
(arming/disarming if the selection list for the particular code is limited to just one partition)

User Manual INTEGRA16
4. as code Ç– performs function assigned to the arrow key (p. 46)
5. as code Å– performs function assigned to the arrow key
6. as code Æ– performs function assigned to the arrow key
7. as code È– performs function assigned to the arrow key
8. open door (entry) – controls the electromagnetic door lock (generates a USER ACCESS
event)
9. open door (exit) – controls the electromagnetic door lock (generates a USER EXIT event)
10.2 long sounds – signals reading of the card code
11.1 short beep – signals that the card code has been read
Notes:
•Selecting the function 2 or 3 to be started by PRESENT CARD will block access to the HOLD
CARD.
•The 8 and 9 functions require that the installer select the door to be opened by the keypad.
It is possible to control any door handled by the system (i.e. opened by code locks,
partition keypads or expanders of proximity card readers).
•Two long beeps can also mean readout of a card with unknown code.
•Readout of an unknown (wrong) code, if repeated three times, may generate a panel
recorded event or an alarm PROG. It can also block the reader in the keypad for 90 sec.
6.2 PARTITION KEYPADS
Fig. 4. INT-S-GR/INT-S-BL partition keypad.

INTEGRA SATEL 17
SATEL offers the following partition keypads for INTEGRA control panels:
−INT-S-GR/INT-S-BL
−INT-SK-GR
These keypads differ by size and shape. The keypads are available with green or blue
backlighting of the keys. Designation of the models with green display ends with "GR" letters,
and that of the models with blue display – with "BL" letters. The backlighting may be
permanent or time-controlled (switched on automatically).
Fig. 5. INT-SK-GR partition keypad.
The partition keypads are provided with LED indicators:
- ALARM (red) – permanent lighting of the LED means alarm. After the alarm time
expires, blinking of the LED indicates the alarm memory. The LED goes off after the
alarm is cleared (see: ALARMS).
Note: The LED may not signal alarms in the armed mode if the installer has enabled the
option DO NOT SHOW ALARM IF ARMED, as required by the CLC/TS 50131-3 standard.
- ARMED (green) – steady light indicates that the partition the keypad is assigned to, is
armed. Blinking indicates that exit delay countdown is underway.
- TROUBLE (yellow) – blinking indicates occurrence of a technical problem. The signaling
refers to the troubles from the entire alarm system, not only from the keypad controlled
partition. Check the LCD keypad for the type of trouble. The LED is off when the
partition controlled by the keypad is armed. Disarming will restore the trouble
signaling. The LED is blinking until troubles are viewed in the LCD keypad and the
trouble memory is reset (option TROUBLE MEMORY UNTIL REVIEW enabled) or until the
trouble cause stops (option TROUBLE MEMORY UNTIL REVIEW disabled) PROG.

User Manual INTEGRA18
When all the LEDs are alternately blinking (from top to bottom), there is no communication
between the keypad and the control panel. This situation may occur when the STARTER
program is running in the control panel or the cable connecting the partition keypad to the
control panel is damaged.
It is possible to program the partition to be armed or disarmed after entering two codes
PROG. In this case, entering the first code causes the LEDs labeled [ARMED] and
[TROUBLE] to blink alternately, while the control panel waits for entering the second code.
Like the LCD keypad, the partition keypad may generate audible signals:
•One short beep – acceptance of the code entry (provided that the option ACCES CODE
SIGNALING (HARDWARE) is enabled).
•One long beep – refusal of arming.
•Two long beeps – the code is unknown to the control panel.
•Two short beeps – acceptance of the first of two codes required for arming or disarming.
•Three long beeps – the code cannot control this partition.
•Three short beeps – confirmation of partition arming and disarming.
•Three pairs of short beeps – it is necessary to change the code – another user, when
changing his code, entered the identical combination of digits to that of the given user, or
the code validity period is expiring.
•Four short and one long beeps – confirmation of performance of a control function, code
change, or a guard round.
•Five short beeps – the dependent door is open – the door control has not been
performed. To operate the lock it is necessary to close the dependent door and reenter the
code.
The audible signaling may be substituted by the keypad illumination blinking PROG.
The beeps are consequently translated into the keypad extinguishing pulses, when the
backlighting is on, or illumination pulses, when the backlighting is normally off.
The partition keypad may also audibly indicate other situations PROG.
•Alarm in partition – continuous sound for the total alarm duration.
•Alarm memory – long beeps every two seconds until the alarm is reset. The sounds are
synchronized with the [ALARM] LED blinking. Pressing any numeric key will mute the
signaling for approximately 40 seconds.
•Fire alarm – a series of long beeps every second for the total alarm duration.
•Fire alarm memory – short beeps every two seconds until the alarm is reset.
The sounds are synchronized with the [ALARM] LED blinking. Pressing any numeric key
will mute the signaling for approximately 40 seconds.
•Countdown of entry delay – 2 short beeps every second.
•Countdown of exit delay – long beeps every 3 seconds, ended with a series of short
beeps (for 10 seconds) and a single long beep. This way of signaling the exit delay
indicates that the countdown is coming to an end before arming.
•Autoarming delay time countdown (timer-controlled partitions) – a series of 7 beeps
(of ever shorter duration).
•Door open too long – short beeps repeated with a high frequency until the door is
closed (with door control function activated).
•Chime in expander – five short beeps – information on violating selected zones in the
partition (CHIME option must be enabled in the partition keypad, and CHIME IN MODULE
option must be active for the zone).
Using the partition keypad you can control the armed mode in one partition and execute the
access control functions for a single door (door lock control).