Amano Pioneer Eclipse PE250AP User manual

Commercial Air Purifier
PE250AP
Operator’s Manual

2
FOR YOUR SAFETY
DO NOT store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
Record This Important Information
Date of Purchase
Purchased From
Address
City State Zip
Phone Contact
Machine Model
Machine Serial Number
Important Phone Numbers
Medical Emergency
Police
Fire Department
WARNING!: The Products sold with this Manual contain or may contain chemicals that
are known to certain governments (such as the State of California, as identied in its
Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other reproductive harm.
In certain locations (including the State of California) purchasers of these Products that place them
in service at an employment job site or a publicly accessible space are required by regulation
to make certain notices, warnings or disclosures regarding the chemicals that are or may be
contained in the Products at or about such work sites. It is the purchaser’s responsibility to know
the content of, and to comply with, any laws and regulations relating to the use of these Products
in such environments. The Manufacturer disclaims any responsibility to advise purchasers of any
specic requirements that may be applicable to the use of the Products in such environments.

3
In this Operation Manual you will find three statements that you must read and observe
to ensure safe operation of this machine.
DANGER! indicates that the possibility of severe bodily injury or death can occur if
DANGER! statements are ignored. Read and observe all DANGER! statements
included in the Operation Manual and attached to the machine.
WARNING! indicates that the possibility of bodily injury to the operator and other
people can occur if WARNING! statements are ignored. Read and observe all
WARNING! statements included in the Operation Manual and attached to the
machine.
CAUTION! indicates that the possibility of damage to the machine or other property
can occur if CAUTION! statements are ignored. Read and observe all CAUTION!
statements included in the Operation Manual and attached to the machine.
Table of Contents
***This product is intended for commercial use only***
Safety Precautions ........................................................... 4
Grounding Instructions ..................................................... 5
Technical Specifications ................................................... 5
Appliance Components .................................................... 6
Appliance Preparation ...................................................... 6
Appliance Maintenance .................................................... 8
Wiring Diagram............................................................... 10
For Best Performance .................................................... 11
Trouble Shooting ............................................................ 11
Parts Manual. ................................................................. 12
Limited Warranty ............................................................ 16

4
WARNING: Read all safety warnings, instructions,
illustrations, and specications provided with
this appliance. Failure to follow all instructions
listed below may result in electric shock, re, and/
or serious injury. This appliance is designed and
manufactured for indoor use. Amano Pioneer Eclipse
Corporation (APEC) does not recommend use of this
appliance in any environment other than an indoor
environment. This oor machine is designed and
manufactured for commercial use only.
WARNING: To reduce the risk of re, electric shock or
injury:
• Do not leave appliance when plugged in.
• Do not leave appliance connected to the electricity
supply when not in use.
• Do not leave the appliance unattended while running.
• Unplug from outlet before servicing.
• Use only as described in this manual. Use only
manufacturer’s recommended components and
attachments.
• Use only indoors. Do not use outdoors or expose to rain.
• Do not use with damaged cord or plug. If appliance is
not working as it should, has been dropped, damaged,
left outdoors, or dropped into water, return it to an
authorized service center.
Safety Precautions
• Do no pull or carry by cord, use cord as a handle,
close door on cord, or pull cord around sharp edges or
corners. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Turn o󰀨 all controls before unplugging.
• Do not attempt to service the unit while appliance is
plugged in.
• Appliance may cause a re when operating near
ammable vapors or materials. Do not operate this
machine near ammable uids, dust or vapors.
• Connect to a properly grounded outlet.
• Do not use with any solid state speed control device.
• This unit is thermally protected.
DANGER: To avoid injury, keep hands, feet, and loose
clothing away from all moving parts on the machine. Do not
operate the machine unless all guards are in place. Never
leave the machine unattended while connected to a power
source.

5
THIS APPLIANCE MUST BE GROUNDED.
If it should malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk electric shock. This machine is equipped
with a cord having an equipment grounding conductor
and grounding plug. The plug must be inserted into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service person if
you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the
appliance - if it will not t the outlet, have a proper outlet
installed by a qualied electrician.
This appliance is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug
illustrated in sketch A.
*This applies only
to North America.
Most other countries
use 230V circuit.
WARNING: UV-C emitted from this product. Avoid
eye and skin exposure to unshielded product. Follow
installation instructions and user manual.
WARNING: Do not operate device without lter and
cover securely attached. Operating in this manner could
expose those nearby to UV-C radiation UV-C radiation
can cause severe burns of the skin and eye injuries,
(photokeratitis).
WARNING: This device uses UV-C bulbs
or lamps that contain Mercury. The U.S.
Environmental Association, (EPA),
classies Mercury as hazardous waste.
The bulbs cannot be disposed as trash
or rubbish. They must be recycled.
For more information, see the following:
US: http://www.lamprecycle.org/
Canada: https://www.canada.ca/en/environment-
climate-change/campaigns/diverting-mercury-
light-bulbs.html
Australia: https://recyclingnearyou.com.au/
For all other regions, please consult your local recycling
authority.
CAUTION: Fan must be operating prior to supplying
power to UV-C bulbs. Supplying power to bulbs without
fan operating will cause bulbs to overheat and fail.
Grounding Instructions
GROUNDING
PIN
GROUNDING
OUTLET
GROUNDED
OUTLET BOX
Description 250AP115 250AP115C 250AP230
Voltage (V) 115 115 230
Current (A) 3.5 3.5 1.8
Power (W) 403 403 414
AIR FLOW
High Speed 2700 CFM 2700 CFM 2700 CFM
4587 CMH 4587 CMH 4587 CMH
Low Speed 1785 CFM 1785 CFM 1785 CFM
3033 CMH 3033 CMH 3033 CMH
Weight 57 lbs (25,9 kg) 57 lbs (25,9 kg) 55 lbs (24,9 kg)
Length 24” (61 cm) 24” (61 cm) 24” (61 cm)
Width 22.5” (57 cm) 22.5” (57 cm) 22.5” (57 cm)
Height 34” (86 cm) 34” (86 cm) 34” (86 cm)
SOUND LEVEL
High Speed 68.9 dBa 68.9 dBa 68.9 dBA
Low Speed 61.9 dBa 61.9 dBa 61.9 dBA
Cord 20 ft x 16/3 SJTW 20 ft x 16/3 SJTW 60 cm x 3,3 mm2| C20 Connection
Fan Blade 6 x 16.5” (42 cm) 6 x 16.5” (42 cm) 6 x 16.5” (42 cm)
Circuit Breaker 12 Amp 12 Amp 5 Amp
GFCI Yes Yes No
Technical Specifications

6
ALL RIGHTS RESERVED - AMANO
PIONEER ECLIPSE CORP.
This drawing and the included concepts are
the property of Amano Pioneer Eclipse Corp.
and is to be returned immediately upon
demand. The designs and concepts shown
hereon are confidential and are not to be
copied, divulged or submitted to others.
CHECKED
FINISH
TOLERANCES UNLESS
OTHERWISE SPECIFIED
FRACTION
2 PLACE DEC.
3 PLACE DEC.
ANGULAR
 1/16
.03
.010
1
REV
DESCRIPTION
APPROVED
DRAWN
MATERIAL
PART OR ASSY. # SCALE SHEET #
AMANO PIONEER ECLIPSE
NOTES:
1. ALL DIMENSIONS ARE IN INCHES (UNLESS OTHERWISE NOTED)
5/14/21
DAC
250AP COMPONENTS
A
NTS
1 OF 1
REVISION HISTORY
REV DESCRIPTION ECN # DRAWN CHECK APPROVED
A INITIAL ISSUE X
POWER CORD
INTERCONNECT CORD
GCFI RECEPTACLE
CIRCUIT BREAKER
POWER SWITCH
HEPA FILTER
PRE FILTER
UV-C BULB
LIGHT FILTER
Appliance Components
Appliance Preparation
Unpacking the Appliance
When the appliance is delivered, carefully inspect the
shipping carton and the machine for damage. Unpack
the machine with caution. If damage is evident, save the
shipping carton so that it can be inspected. Contact the
Amano Pioneer Eclipse Customer Service Department
or your authorized Amano Pioneer Eclipse Distributor.
Bulb Installation
WARNING: UV-C emitted from this product.
Avoid eye and skin exposure to unshielded product.
CAUTION: Do not operate device without lter and
cover securely attached
1. Make sure appliance is not plugged into a power
source.
2. Disconnect interconnect cord (Figure 1) from the
appliance’s cover.
3. Remove retaining screw (Figure 2) from the cover.
Note the orientation of the cover relative to the
appliance.
4. Remove cover and lay upside down.
Figure 1
Figure 2

7
Appliance Preparation
5. Remove the two packaged bulbs from inside
the HEPA lter.
6. Remove bulbs from packaging and screw into
sockets (Figure 3) attached to the cover.
CAUTION: Do not use a tool to tighten the bulbs.
Only tighten by hand. Tighten bulbs by grasping the
plastic base. Do not grasp the glass tubes.
7. Carefully reposition the cover (Figure 4) over the
HEPA lter. Make sure cover is oriented as
previously installed and bulbs are not contacting
any surface.
8. Secure cover with retaining screw. Connect
interconnect cord. Device is now ready for
operation.
Operation
1. Unwrap the power cord and plug into the properly
grounded outlet.
2. Make sure the interconnect cord is connected to the
receptacle on the base unit and the receptacle on
the cover above the fan.
3. Place the air mover in the desired operating position.
4. Set the switch at the desired speed: low or high.
Circuit Protection
The 250AP features a circuit breaker that will “trip” if
more than the rated electrical current is drawn through
the cord. In addition, some models are equipped with
a duplex GFCI outlet. The GFCI protection promotes
operator safety and will “trip” if an electrical ground fault
is sensed. To test the GFCI protection, press the TEST
button. If operating properly, the RESET button on the
GFCI outlet will pop out.
Figure 3
Figure 4

8
Appliance Maintenance
Scheduled Maintenance
Operation Interval
Replace Pre-Filter Every 30 days or 600 hrs.1
Replace Light Filter Every 90 days or 1800 hrs.1
Tighten UV-C Bulbs Every 90 days or 1800 hrs2
Replace HEPA Filter Every year or 8,000 hrs.1
Replace UVC-Bulbs Every year or 8,000 hrs.2
1 Replace lters more frequently in dusty or dirty environments.
2Replace bulbs more frequently if appliance is commonly moved.
Pre-Filter Replacement
WARNING: Those replacing the Pre-Filter should wear
appropriate personal protective equipment, (PPE):
- A properly-tted N95 or higher mask
- Eye protection, (safety glasses, goggles, or face shield)
- Disposable gloves
1. Make sure appliance is not plugged into a power
source.
2. Disconnect interconnect cord from the appliance’s
cover.
3. Remove dirty Pre-Filter, secure in trash bag, and
dispose with regular trash.
4. Place new Pre-Filter over HEPA (Figure 5). Connect
interconnect cord. Device is now ready for operation.
HEPA Replacement
WARNING: UV-C emitted from this device.
CAUTION: Do not operate device without lter and
cover securely attached.
1. Follow all safety guidelines and instructions for
removing Pre-Filter.
2. Make sure appliance is not plugged into a power
source and the interconnect cord is disconnected
from the appliance’s cover.
3. Remove retaining screw from the cover. Note the
orientation of the cover
4. Remove the HEPA lter, secure in a trash bag,
and dispose with regular trash.
5. Place new HEPA lter (Figure 6) on unit base.
6. Carefully reposition cover over HEPA lter. Make
sure cover is oriented as previously installed and
bulbs are not contacting any surface.
7. Secure cover with retaining screw. Place new
Pre-Filter over HEPA lter.
8. Connect interconnect cord. Device is now ready
for operation.
Light Filter Replacement
WARNING: UV-C emitted from this device.
CAUTION: Do not operate device without lter and
cover securely attached.
1. Follow all safety guidelines and instructions for
removing Pre-Filter and HEPA lter.
Figure 5
Figure 6

9
Appliance Maintenance
2. Make sure appliance is not plugged into a power
source and the interconnect cord is disconnected from
the appliance’s cover. Remove cover and HEPA lter.
3. Loosen, but do not remove, the four screws that
secure cover support to the base.
4. Twist the cover support (Figure 7) clockwise
approximately 1 in, (2,54 cm), and lift up.
5. Remove the old light lter and discard.
6. Replace with new light lter and reverse the
removal process.
NOTE: When securing the cover support to the base,
align dots (Figure 8) on the cover support with the base.
Light Bulb Replacement
WARNING: UV-C emitted from this device.
CAUTION: Do not operate device without lter and
cover securely attached.
WARNING: This device uses UV-C bulbs or lamps that
contain Mercury. The U.S. Environmental Protection
Agency, (EPA), classies Mercury as hazardous waste.
The bulbs cannot be disposed as trash or rubbish.
They must be recycled. For more information, see the
following:
US: http://www.lamprecycle.org/
Canada: https://www.canada.ca/en/environment-
climate-change/campaigns/diverting-mercury-
light-bulbs.html
Australia: https://recyclingnearyou.com.au/
For all other regions, please consult your local recycling
authority.
CAUTION: Fan must be operating prior to supplying
power to UV-C bulbs. Supplying power to bulbs without
fan operating will cause bulbs to overheat and fail.
1. Make sure appliance is not plugged into a
receptacle or other power source and the
interconnect cord is disconnected from the
appliance’s cover.
2. Remove retaining screw from the cover. Note the
orientation of the cover.
3. Place the cover upside down on a sturdy, horizontal
surface.
4. Remove the old bulb(s) (Figure 9) and replace with
the new one(s).
CAUTION: Do not use a tool to tighten bulbs. Only
tighten by hand. Tighten bulbs by grasping the plastic
base. Do not grasp the glass tubes.
5. Recycle old bulbs in accordance with all applicable
regulations.
Figure 7
Figure 8
Figure 9

10
Wiring Diagram