Amart Furniture 53038 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1-5
63cm
62cm
115-125cm
Bathurst Gaming Chair
ITEM CODE:53038
53038

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean,level,spacious assembly area.Avoid hard surfaces that
may damage the product
2.Take care when lifting.Product should be assembled as near as possible to
the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning
assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
ALLOW 20 MINUTES 1 PEOPLE REQUITED
ADDITIONAL TOOLS REQUIRED
2-5 53038

PARTS LIST
1 BACK
2 ARMREST (L)&(R)
3 SEAT
4 MECHANISM
5 GAS LIFT
6 GAS LIFT COVER
7 BASE
8 CASTOR
45 6
7
8
4xPCS
1/4"x16mm
bolt bolt
AB
10xPCS
1/4"x25mm
C
6xPCS
14x8.5mm
3
1
2
D
4xPCS
16x6.5mm
Washer
Washer
3-5 53038

STEP 1: STEP 2:
8
7
5
6
4-5 53038
Insert castor (8) to base (7). Insert gas lift (5) to base (7) as
instruction shown, then put gas lift
cover (6) on gas lift (5).
A
4
3
Mount mechanism (4) to seat (3)
using bolt A.
CARE AND MAINTENANCE
DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER
USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME
DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
OFFICE CHAIR
DO NOT REMOVE THIS LABEL
STEP 4:
Connect back (1) with mechanism
(4) using bolt B and Washer D.
Then connect armrest (2) with
seat (3) using bolt B and Washer C.
B
B
CD
1
2
STEP 3:
CARE AND MAINTENANCE
DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER
USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME
DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
OFFICE CHAIR
DO NOT REMOVE THIS LABEL

STEP 5:
5-5 53038
Put back (1) on gas lift (5). Assembly is complete.
STEP 6:
CARE AND MAINTENANCE
DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER
USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME
DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
OFFICE CHAIR
DO NOT REMOVE THIS LABEL