Amart Furniture VIKA 64084 User manual

ASSEMBLY INSTRUCTION
ITEM CODE -
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any assistance with
assembly or for missing parts please phone Amart Furniture, Customer Service
Freecall 1800 351 084.
1 / 3 64084
64084
VIKA BEDSIDE
Furniture

2 / 3 64084
Restraint to avoid tipping of Bed Side
It is strongly recommended that you fit the restraint strap provided with your furniture chest
to avoid accidental tipping on uneven flors or from improper use.
Parts List
1. Bracket...................2 pcs
2. Short Screw............2 pcs
3. Long Screw............2 pcs
4. PLastic Anchor.......2 pcs
5. Strap.......................1 pcs
Installation Instruction :
Step 1 :
Attach a Bracket (1) to the back of the furniture frame near the top using Short Screw(2).
Step 2 :
Mark a spot on the wall approximately one inch below the level of the Bracket(1) that is
installed on the furniture.
Attach a second Bracket(1) to the wall on this mark so that it lines up vertically with the
Bracket(1) on the back of the furniture.
To install the Bracket(1) to the wall, first drill two 3/16'' holes in the wall at the mark using
the Bracket(1) as a templete for hole position.
Insert Plastic Anchors(4) into the holes in the wall.
Tap Plastic Anchors(4) lightly with a hammer until they are seated flush with the wall.
Attach Bracket(1) to the Plastic Anchors(4) using Long Screws(3).
Step 3 :
Move the furniture to its final position. Line up the Bracket(1) on the wall with the Bracket(1)
that is located on the back of the furniture. Thread Strap(5) through each of the two
brackets(1) as shown. Pull Strap(5) snug, but do not over tighten.
Step 4 :
Check to make sure Bracket(1) are securely fastened to the wall and to the furniture and that
the Strap(5) is locked and snug.
This complete the tipping restraint installation.
12 3 4 5
1
22
3
3
14
451
1

3 / 3 64084
Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
.Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.