Amart Furniture NAHLA 70751 User manual

ASSEMBLY INSTRUCTION
NAHLA QUEEN BED
ITEM CODE - 70751
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Pty Ltd,Qld, Brisbane Australia. For any assistance with
assembly or for missing parts please phone Amart Furniture, Customer Service
Freecall 1800 351 084.
170751
1027mm
1620mm
2111.5mm
Furniture

PRE-ASSEMBLY PREPARATION
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
270751

3
HEADBOARD FRAME1
2
3
4
5
6
CENTRE BAR
SIDE RAILS - L/R
PARTS LIST
M8- Allen key
M6- Allen key
G-1 Pc
C-9 Pcs D-8 Pcs
M6x35mm M8x35mm
B-6 PcsA-12 Pcs
M8x25mm M6x15mm
E-8 Pcs H-1 Pc
Chipboard screw
F-4 Pcs
#4 x 30 mm
1 PC
1 UNIT
1 PC7
8
9- 18mm x 59mm x 1523mm
WOOD SLATS
2 PCS
2 PCS
12 PCS
Wood Dowel M8 x 30mm
HEADBOARD LEG - RIGHT
FOOTBOARD FRAME
2 PCS
CROSS BARS
SUPPORT LEGS c/w
M8 x 40mm JCBB Bolt
HEADBOARD BACK SUPPORT
1 PC
8
8
10
1
2
5
4
5
6
7
9
3
10
70751
10
HEADBOARD LEG - LEFT 1 PC
1 PC

4
STEP 1 : Attach headboard legs '2' & '3' to the headboard frame '1' using bolts 'D' as shown
and tighten with allen key 'H'. After that attach back support '10' using bolts 'C' and dowels 'F'
and tighten with allen key 'G'.
STEP 2 : Fix headboard ' 1 ' & footboard drawer box ' 4 ' to the side rails ' 5 ' with bolts 'A' as
shown using allen key ' H '.Important note : Do not tighten the bolts yet!
D
2
1
3
1
C
F
10
C-8 Pcs
D-8 Pcs
M6x35mm
M8x35mm
F-4 Pcs
Wood Dowel M8 x 30mm
A1
5
4
A-12 Pcs
M8x25mm
70751
M6- Allen key
G-1 Pc
M8- Allen key
H-1 Pc
M8- Allen key
H-1 Pc

5
STEP 3 : Fix cross bar ' 6 ' to the side rail with bolts ' B ' as shown using allen key ' G '.
B
STEP 4 : Fix center bar ' 7 ' to the cross bar ' 6 ' and footboard drawer box with bolts ' B ' & ' C ' as
shown using allen key ' G '.
B-4 Pcs
M6x15mm
6
C-1 Pc
M6x35mm B-2 Pcs
M6x15mm
C
B
7
6
70751
M6- Allen key
G-1 Pc
M6- Allen key
G-1 Pc

6
ASSEMBLY COMPLETE
STEP 6 : Put wood slats ' 9 ' to the side rails support and fix screws ' E ' at hole as shown.
STEP 5 : Fix bed support legs ' 8 ' as shown and tighten all bolts using allen key ' H '.
8
E
9
E-8 Pcs
Chipboard screw
#4 x 30 mm
IMPORTANT NOTE:
ALWAYS LIFT YOUR BED WHEN MOVING/RELOCATING - DO NOT DRAG.
DRAGGING CAN CAUSE THE CENTER SUPPORT LEGS TO BEND/BREAK.
70751
M8- Allen key
H-1 Pc

7
Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
.Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.
70751