Amart Furniture CHANELLE KING 64406 User manual

ITEM CODE : 64406
1 64406
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1190mm
1200mm
2120mm
ASSEMBLY INSTRUCTION
CHANELLE KING SINGLE BED

2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
3. Ensure that you have all required contents for complete assembly
64406
12
11 1
2
10
8
7
4
5
9 3
6
X2
ADDITIONAL TOOLS REQUIRED (not include)
ALLOW 30 MINUTES 2 PEOPLE REQUIRED

3
PART LIST
HARDWARE LIST
16 PCS
B. JCBC BOLT (M6x60MM)
3 PCS
A. JCBC BOLT (M6x35MM)
3
4
FOOTBOARD
1HEADBOARD PANEL (X1)
7
6(X3)
(X3)
SIDE RAILS
SUPPORT LEGS
2a HEADBOARD LEG RIGHT (X1)
5MIDDLE RAIL
SLATS
1190x705x50mm
850x70x25mm
278x40x40mm
1066x60x18mm
(X1)
(X2)
(X1)
1155x507x400mm
1588x120x50mm
1384x60x20mm
2b HEADBOARD LEG LEFT (X1) 850x70x25mm
3
6
6
6
4
4
5
1
2a
7
2b
C. JCBC BOLT (M8x25MM)
8 PCS
D. SCREW (M4x30MM)
20 PCS
64406
8(X10)
MIDDLE SLATS 1066x60x18mm
8
8
10 PCS
E. FLAT WASHER
(M6/Ø14MM)
10 PCS
F. SPRING WASHER
(M6/Ø10MM)
1 PC
G. ALLEN KEY M4 H. ADHESIVE FELF PAD
(20X20X5MM)
12 PCS

H
4 64406
H
With two people carefully lay the Footboard on to a sheet or piece of cardboard.
Attach adhesive felt pad onto the legs.
With two people carefully stand the Footboard upright.
H

STEP 2
Tighten the headboard leg 2a,2b to headboard panel 1with bolts A, spring washer Fand flat washer E.
1
AFE
G
2a
2b
64406
STEP 1
Attach the handle
Take out handle from drawer, use
screwdriver removing the bolts. Attach handle in front of drawers,
on the drilling hole position by using
screwdriver to tighten bolts up.
5

STEP 4
Tighten the slats 7and middle rail 5to all support legs 6with bolts B.
B
G
7
5
6
64406
3
4
4
2b
2a
C
G
STEP 3
Attach side rails 4to headboard legs 2a, 2b and footboard 3by interlocking the brackets on the side rail
with the bolts Con the headboard/footboard and then push down to lock in place
Assembly these components out of bed frame.
H frame
6
6
6

STEP 6
64406
STEP 5
Use two people to place H frame onto 4.
Attach H frame onto 4using the bolt (A), tighten it up by using an allen key (G).
G
A
H frame
4
4
Attach 8onto 4using the screws (D), tighten it up by using an screwdriver.
D
4
8
4
7

ASSEMBLY IS COMPLETE
864406
IMPORTANT NOTE:
.Once the bed is positioned and the support legs are adjusted to touch
floor, the slats can then be laid down and secured before putting on the
mattress.
. DO NOT push or pull the bed if there is a need for re-positioning as this
may result in broken support legs for the centre rail.

IMPORTANT: CARE GUIDE FOR YOUR TIMBER FURNITURE
Congratulations! You have just purchased a quality product from
Amart furniture. Please read on for important information
regarding your purchase…
A multi-step finish is applied to all our furniture, but all wood comes from nature.
Because of this, there will be natural variations in surface texture and grain like knots,
mineral streaks and sap runs that may affect the finish.
These differences in character are not defects, but distinctions that make each pie ce of
furniture unique.
Our furniture is built to last. Following these step, basic care should protect your
investment for years to come.
Dust frequently with a clean damp lint-free cloth. This will help remove abrasive
build up which can damage a finish over time.
Do not place hot objects on any furniture surface. Always use suitable placemat.
Laminate and lacquer finishes on table tops provide added scartch and heat
resistance to our furniture, but they can still be damaged without proper care.
Avoid exposing your furniture to strong sunlight, heat, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture and sudden extreme temperature and humidity change can cause
cracking or splitting.
Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require proffesional repairs.
Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placemats etc may soften and mark the finish in left in contact with
the furniture for period of time.