Amart Furniture ESKO 70369 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
ESKO BEDSIDE
ITEM CODE 70369
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351
084
1ITEM CODE 70369

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2 ITEM CODE 70369
ALLOW 20 MINITES 2 PEOPLE REQUIRED
TOOLS REQUIRED
12
11
10
9
8
765
4
3
2
1
We recommend using a
screwdriver to put this item
together. However if you choose
to use a power drill it must be
used on LOW SPEED (LOW
TORQUE) as too much pressure
could damage the product

3 ITEM CODE 70369
PARTS LIST

ITEM CODE 703694
1
SIDE BOARD
2
SIDE BOARD
3
TOP SUPPORT BOARD
4
BOTTOM BOARD
5
BACK BOARD
6
DRAWER SIDE BOARD
7
DRAWER SIDE BOARD
8
DRAWER BACK BOARD
9
DRAWER BOTTOM BOARD
10
DRAWER SURFACE BOARD
11
GLASS TOP
N.

ITEM CODE 703695

ITEM CODE 703696
STEP:1
STEP:2

ITEM CODE 703697
STEP:3
STEP:4

ITEM CODE 703698
STEP:5
STEP:6

ITEM CODE 703699
STEP:7
STEP:8

ITEM CODE 7036910
STEP:9

ITEM CODE 7036911
STEP:10

ITEM CODE 7036912
STEP:11
STEP:12

ITEM CODE 7036913
STEP:13
STEP:14

14 TEM ICODE 70369
ASSEMBLY IS COMPLETE

15 TEM ICODE 70369
SAFETY BRACKETS INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach
the Mounting Plate into a stud. If mounting into brick or masonry you will need to
acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and furniture
and that the Wall Strap is snug.
HARDWARE
Mounting Plate x 2 Wall Strap x 1 Large Screw x2 Small Screw x2

16
To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto your
furniture as sharp material may scrape and damage the finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
WARNING:
•Do not place very hot or cold items on the glass surface unless
adequately thick table mats are used to prevent such items
coming in contact with the glass
•Do not sit or stand upon the glass surface
•Do not use the glass as a chopping surface
•Do not strike the glass with hard or pointed items
•When cleaning the glass panels use a damp cloth or leather with
washing up liquid or soft soap if necessary. Do not use washing
powders or any other substances containing abrasives since
these may scratch the glass
TEM ICODE 70369