Amart Furniture Rose Bay 64421 User manual

ASSEMBLY INSTRUCTION
ROSE BAY QUEEN BED
ITEM CODE 64421
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
164421
2145mm
1100mm
1660mm

2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
3. Ensure that you have all required contents for complete assembly
64421

3
PARTS LIST
2
3
4
5Middle rails 2 pcs 4 pcs
1Headboard 1 pc
Side rail 2 pcs
2 pcs
NO. PARTS LIST QT'Y
Support legs
Middle Slats
Footboard 1 pc Bolt M6x50mm 4 pcs
NO. HARDWARE LIST QT'Y
B
CScrew M4x30mm 30 pcs
DAllen Key 4mm 1 pc
6
A
Bolt M8x20mm 8 pcs
1
2
3
3
4
5
7
64421
6
13 pcs
Slats
7
7
EAdhesvise felt pad
20x20x5mm
4 pcs

464421
Attach adhesive felt pad (E) onto the legs
E
E

D
B(X8)
D
A
(X4)
2
1
3
3
6
4
5
STEP 1: Attach 3onto 1and 2using the bolts (B), tighten it up by using an allen key (D)
STEP 2: Attach 5onto 4and 6using the bolts (A), tighten it up by using an allen key (D)
64421
Assembly these components out of bed frame.
H frame
5

STEP 3: Use two people to place H frame onto 3.
Attach H frame onto 3using the screws (C), tighten it up by using an screwdriver.
C(X4)
H frame
C(X26)
STEP 4: Attach 7onto 3using the screws (C), tighten it up by using an screwdriver.
7
664421

ASSEMBLY IS COMPLETE
64421
7
IMPORTANT NOTE:
.Once the bed is positioned and the support legs are adjusted to touch
floor, the slats can then be laid down and secured before putting on the
mattress.
. DO NOT push or pull the bed if there is a need for re-positioning as this
may result in broken support legs for the centre rail.

IMPORTANT: CARE GUIDE FOR YOUR TIMBER FURNITURE
Congratulations! You have just purchased a quality product from
Amart furniture. Please read on for important information
regarding your purchase…
A multi-step finish is applied to all our furniture, but all wood comes from nature.
Because of this, there will be natural variations in surface texture and grain like knots,
mineral streaks and sap runs that may affect the finish.
These differences in character are not defects, but distinctions that make each piece of
furniture unique.
Our furniture is built to last. Following these step, basic care should protect your
investment for years to come.
Dust frequently with a clean damp lint-free cloth. This will help remove abrasive
build up which can damage a finish over time.
Do not place hot objects on any furniture surface. Always use suitable placemat.
Laminate and lacquer finishes on table tops provide added scartch and heat
resistance to our furniture, but they can still be damaged without proper care.
Avoid exposing your furniture to strong sunlight, heat, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture and sudden extreme temperature and humidity change can cause
cracking or splitting.
Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require proffesional repairs.
Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placemats etc may soften and mark the finish in left in contact with
the furniture for period of time.