Amart Furniture Jumbo 38702 User manual

ASSEMBLY INSTRUCTION
PERSIAN JUMBO SINGLE BED
ITEM CODE - 38702
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any assistance with
assembly or for missing parts please phone Amart Furniture, Customer Service
Freecall 1800 351 084.
1160mm
2140mm
855mm
1 38702
Furniture

PRE-ASSEMBLY PREPARATION
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
2 38702

C x 2pcs
M8 x 25mm
B x 8pcs
M8 x 40mm
A x 8pcs
Double End Plastic Cap
1
3
3
2
4
6
6
5
4
8
8
D x 10pcs
M6 x 40mm
E x 1pc
M6-Allen Key
F x 1pc
M8-Allen Key
7
7
HEAD FRAME
FOOT FRAME
SIDE RAILS
END CROSS BARS
CENTER CROSS BAR
SUPPORT LEGS
1
2
3
4
5
6
7
8
CROSS BAR
WOOD SLATS
PARTS LIST
3 38702
- 9mm x 60mm x 914mm
1 pc
1 pc
2 pcs
2 pcs
1 pc
2 pcs
2 pcs
16 pcs

3
6
3
D
STEP 1 : Fix both side rails (3) and center cross bar (5) with bolt (D) using Allen key (E).
STEP 2 : Put cross bar (6) into side rail and fix in bolt (D) using Allen key (E).
D
D
D
D
D
5
6
4 38702

4
4
7
D
STEP 4: Attach the support legs (7) to center cross bars (5) with bolts (C) using Allen key (F).
STEP 3: Attach the end cross bars (4) and tighten with bolt (D) using Allen key (E).
5 38702
D
D
D
C
5

1
B
2
5
8
8A8
STEP 5: Attach head frame (1) to side rails with bolts (B). Repeat step with foot frame (2).
Tighten all bolts with hexagon key (F).
STEP 6 : Insert wooden slats (8) into both ends of the double end plastic cap (A).
Insert other ends of slats into provided holes in end cross bars (4) then align the plastic caps
with the centre cross bar (5) as shown. Press down on the caps gently to secure.
6 38702
B
4
4
8

7 38702
Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
.Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.