Amart Furniture MARSEILLE 67376 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
MARSEILLE BUFFET
ITEM CODE 67376
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351
084
1ITEM CODE 67376

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2 ITEM CODE 67376
ALLOW 20 MINITES 2 PEOPLE REQUIRED
TOOLS REQUIRED
12
11
10
9
8
765
4
3
2
1

3 ITEM CODE 67376
PARTS LIST
C. ALLEN KEY
A. BOLT M6X45MM
AX12
B. SCREW M4X30MM
CX1
BX4
D. WALL FIXING
M4X30mm M3.5X14mm DX1
1BUFFET BODY
2REAR FEET
3RIGHT FRONT FOOT
4LEFT FRONT FOOT
5CENTRE SUPPORT

ITEM CODE 67376
•Attach centre support(5)to buffet body (1) using screw(B)
•Tighten with screwdriver
4
B. SCREW M4X30MM
4PCS
ITEMS REQUIRED
1

ITEM CODE 67376
•Attach foot (2)(3)(4)to buffet body (1) using bolt(A)
•Tighten with Allen Key (c).
5
C. ALLEN KEY A. BOLT M6X45MM
12PCS
1PCS
ITEMS REQUIRED
2

6TEM ICODE 67376
ASSEMBLY IS COMPLETE

7TEM ICODE 67376
SAFETY BRACKETS INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach
the Mounting Plate into a stud. If mounting into brick or masonry you will need to
acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and furniture
and that the Wall Strap is snug.
HARDWARE
Mounting Plate x 2 Wall Strap x 1 Large Screw x2 Small Screw x2

8TEM ICODE 67376
CARE AND MAINTENANCE
•A multi-step finish is applied to all our furniture, but all wood comes
from nature. Because of this, there will be natural variations in surface
texture and grain like knots, mineral streaks and sap runs that may
affect the finish. These differences in character are not defects, but
distinctions that make each piece of furniture unique.
•Our furniture is built to last. Following these steps for basic care
should protect your investment for years to come.
•Dust frequently with a clean damp lint-free cloth. This will help
remove abrasive build up which can damage a finish over time.
•Do not place hot objects on any furniture surface. Always use a hot
plate or placemat. Laminate and lacquer finishes on table tops provide
added scratch and heat resistance to our furniture, but they can still
be damaged without proper care.
•Avoid exposing your furniture to strong sunlight, heat outlet, open
windows or dampness. Prolonged exposure to direct sunlightcan fade
the finish of your furniture, while extreme temperature and humidity
changes can cause cracking or splitting.
•Do not expose your furniture to any liquids. Never allow water to sit
on your furniture. Alcohol, nail polish and perfume are also dangerous
as they will dissolve the lacquer finish on contact and may require
professional repairs.
•Do not allow plastic to come in direct contact with your furniture.
Chemicals in the plastic of placemats etc may soften and mark the
finish if left in contact with the furniture for a period of time.