Amart Furniture Locklyn 72733 User manual

ASSEMBLY INSTRUCTION
LOCKLYN QUEEN 4 POST BED
ITEM CODE 72733
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1
2100mm
1700mm
2135mm
72733

2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
3. Ensure that you have all required contents for complete assembly
72733

2
3
4
5
Middle rails
2 pcs
6 pcs
1 Headboard 1 pc
Side rails
2 pcs
3 pcs
NO. PARTS LIST QT'Y
Support legs
Middle Slats
Footboard 1 pc
Bolt M6x75mm 12 pcs
NO. HARDWARE LIST QT'Y
B
C
D
Allen Key 4mm 1 pc
6
A
Bolt M8x25mm 8 pcs
14 pcs
Slats
7
3
PARTS LIST
10
11
8b
1 pc
1 pc
Vertical Headboard rail-right
9a
9b
8a
Vertical Footboard rail-right
F
G
Bolt M6x60mm 6 pcs
Bolt M6x35mm 6 pcs
Flat washer M6xØ14
12 pcs
Spring washer M6
12 pcs
Screw M4x30mm 28 pcs
E
H
4 pcs
I
Adhesive felt pad
Ø20x5
7
7
6
1
2
3
3
4
5
5
5
5
5
5
8b
8a
9b
9a
10
11
K
Screw M6 x 100mm 4 pcs
Wood Dowel 8 pcs
M
10 2 pcs
Cross top rails
11 2 pcsHorizontal top rails
Vertical Headboard rail-left
1 pc
1 pc
Vertical Footboard rail-left
72733

4
Attach adhesive felt pad (M) onto the legs.
Attach headboard (1) onto vertical headboard rail-right (8a) and vertical headboard rail-left (8b)
using the bolts (A),Spring washer (B) and Flat washer (C), tighten it up by using an allen key (G).
Attach footboard (2) onto vertical footboard rail-right (9a) and vertical footboard rail-left (9b)
using the bolts (A),Spring washer (B) and Flat washer (C), tighten it up by using an allen key (G).
Attach adhesive felt pad (M) onto the legs.
C
B
A
G
(x3)
C
B
A
G
(x3)
K
K
K
K
8a
8b
STEP 1: Attach wood dowels (K) onto headboard and vertical headboard rails.
M
(x2)
M frame
1
STEP 1: Attach wood dowel (K) onto footboard and vertical footboard rails.
C
B
A
G
(x3)
C
B
A
G
(x3)
K
K
K
K
9b
9a
2
N frame
M
(x2)
72733

5
M frame
N frame
STEP 3: Attach side rails (3) onto (M frame) and (N frame) using the bolts (D), tighten it up by
using an allen key (G).
D
G
(x8)
3
3
STEP 4: Attach cross top rails (10) and horizontal top rails (11) onto vertical headboard rail-right
(8a), vertical headboard rail-left (8b), vertical footboard rail-right (9a) and vertical footboard rail-left
(9b) using the screws (i) tighten it up by using an allen key (G).
G
I
(x4)
11
11
9a
9b
8b
8a
10
10
72733

6
Y frame
6
5
5
5
5
5
5
G
E(x6)
Y frame
G
F(x6)
3
3
STEP 6: Use two people to place (Y frame) onto side rails (3).
Attach (Y frame) onto side rails (3) using the bolts (F), tighten it up by using an allen key (G).
STEP 5: Attach support legs (5) onto middle rails (4) and middle slats (6) using the bolts (E),
tighten it up by using an allen key (G).
4
72733
Assemblethese components out of bed frame.

7
ASSEMBLY IS COMPLETE
7
7
3
3
(X28)
H
STEP 7: Once the bed is positioned and the support legs are adjusted to touch floor,the slats
can then be laid down and secured before putting on the mattress.
Attach slats (7) onto side rails (3) using the screws (H), tighten it up by using a screwdriver.
72733
. DO NOT push or pull the bed if there is a need for re-positioning as this may result in broken
support legs for the centre rail.
IMPORTANT NOTE:

suitable
and sudden