Amart Furniture MILL 66295 User manual

1675mm
1960mm
975mm
ASSEMBLY INSTRUCTION
MILL SINGLE HOUSE BED
ITEM CODE : 66295
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture Pty Ltd Customer Service Free call 1800 351 084
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture Pty Ltd, Customer Service Free call 1800 351 084
PAGE 1 OF 10 66295

ALLOW 45 MINUTES 2 PERSON REQUIRED
ADDITIONAL TOOLS REQUIREDADDITIONALADDITIONAL TOOLS REQUIRED
PRE-ASSEMBLY PREPARATION
x2
WARNING :
- This bed can present a serious risk of injury from strangulaon if not used correctly. Never aach or
hang items to any part of the bed that are not designed to be used with the bed, for example, but
not limited to ropes, strings, cords, hooks, belts and bags.
- Do not use the bed if any structural part is broken or missing.
- Prohibit horseplay on or under the bed.
- Prohibit jumping on the bed.
- All assembly fastenings should always be ghtened properly and that care should be taken that no
fings are loose. Periodically check all fastenings to ensure they are secure.
NO POWER DRILL
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
2. Take care when liing. Product should be assembled as near as possible to the point of use.
3. Ensure that you have all required contents for complete assembly.
4. Always read the assembly instrucons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over ghten the screws and bolts as this may damage the threads.
7. Do not use power drills and drivers for ghten the screws and bolts as this may damage the item.
PAGE 2 OF 10 66295

66295
PAGE 3 OF 10
1L
4
5
1R
2L
3L
2R
3R
8
7
6
4 HEADBOARD RAIL (X2)
3L,3R HEADBOARD ROOF - REAR (L&R) (X2)
2L,2R HEADBOARD ROOF - FRONT (L&R) (X2)
1L,1R HEADBOARD POST (L&R) (X4)
8 WOODEN SLAT (72 x 915 = 16) (X1)
7 SUPPORT RAIL - MIDDLE (X2)
6 SUPPORT RAIL - TOP (X1)
5 SIDE RAIL (X2)

66295
PAGE 4 OF 10
A. PLASTIC DOWEL (M10 x 35MM)
20 PCS
B. JCBC BOLT (M6 x 60MM)
16 PCS
C. JCBC BOLT (M6 x 100MM)
10 PCS
D. JRN NUT (M6 x 13MM)
26 PCS
E. JCBC W SCREW (M7 x 25MM)
8 PCS
F. CSK C/B SCREW (M4 x 32MM)
6 PCS
G. ALLEN KEY (M4 x 60MM)
1 PC
H. FURNITURE GLUE 10G
1 PC
HARDWARE LIST

66295
PAGE 5 OF 10
STEP 1
Apply a small amount of Furniture Glue (H) into boom and inside of Ø10MM holes before insert
Plasc Dowels (A) on Headboard Roof - Front (2L & 2R), Headboard Rail (4), Side Rails (5) and
Support Rail - Middle (7).
STEP 2
Apply a small amount of Furniture Glue (H) into boom and inside of the Ø10MM holes.
Aach and secure Headboard Rail (4) to Headboard Post (1L & 1R) by using Bolts (C) & Nuts (D),
ghten it up by using Allen Key (G).
2R
2L 4
4
5
5
7
7
1L
1R
4
1L
1R
4

66295
PAGE 6 OF 10
STEP 3
Apply a small amount of Furniture Glue (H) into boom and inside of the Ø10MM holes for Plasc Dowels (A)
of Headboard Roof - Rear (3L & 3R) for assembly to Headboard Roof - Front (2L & 2R).
Aach and secure Headboard Roof - Rear (3L & 3R) to Headboard Roof - Front (2L & 2R) by using Bolts (C) &
Nuts (D), ghten it up by using Allen Key (G).
STEP 4
Apply a small amount of Furniture Glue (H) onto the end part of Headboard Post (L&R) for assembly to
Headboard Roof.
Aach and secure Headboard Roof to Headboard Post (1L & 1R) by using Screws (E),
ghten it up by using Allen Key (G).
3L
3R
2R
2L
1L
1R
3L
3R
2R
2L
1L
1R

66295
PAGE 7 OF 10
STEP 5
Aach and secure Side Rail (5) and Support Rail - Top (6) &Support Rail - Middle (7) to Headboard
by using Bolts (B) & Nuts (D), ghten it up by using Allen Key (G).
3L
3R
2L
2R
6
7
7
1L
1R 1L
1R
5
5

66295
PAGE 8 OF 10
STEP 6
Secure Wooden Slats (8) by using Screws (F), ghten it up by using Crosshead Screw Driver.
*Align both Side Rails before ghtening the screws.
8

66295
PAGE 9 OF 10
ASSEMBLY IS COMPLETE

66295
PAGE 10 OF 10
IMPORTANT : PRODUCT CARE FOR TIMBER ITEMS
As our mber is supplied from sustainable forests there will be natural variaons in surface texture and
grain like knots, mineral streaks and sap runs that may affect the finish. These differences in character
are not defects, but disncons that make each piece of furniture unique.
Our furniture is built to last. Following these steps for basic care should protect your investment for
years to come.
• Dust frequently with a clean damp lint-free cloth. This will help remove abrasive build up which can
damage a finish over me
• Do not place hot objects on any furniture surface. Always use a hot plate or placemat. Laminate and
lacquer finishes on table tops provide added scratch and heat resistance to our furniture, but they can
sll be damaged without proper care
• Avoid exposing your furniture to strong sunlight, heat outlet, open windows or dampness. Prolonged
exposure to direct sunlight can fade the finish of your furniture, while extreme temperature and
humidity changes can cause cracking or spling
• Do not expose your furniture to any liquids. Never allow water to sit on your furniture. Alcohol, nail
polish and perfume are also dangerous as they will dissolve the lacquer finish on contact and may
require professional repairs
• Do not allow plasc to come in direct contact with your furniture. Chemicals in the plasc of placemats
etc. may soen and mark the finish if lein contact with the furniture for a period of me