Amart Furniture MALLORY 67093 User manual

ASSEMBLY INSTRUCTION
ITEM CODE -
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
Imported by Amart Furniture Pty Ltd,Qld, Brisbane Australia. For any assistance with
assembly or for missing parts please phone Amart Furniture, Customer Service
Freecall 1800 351 084.
1 / 8 67093
67093
MALLORY QUEEN BED
Furniture

PRE-ASSEMBLY PREPARATION
2 / 8 67093
BEFORE YOU START....
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product.
2. Check and ensure that you have all required contents for complete assembly.
3. Always read the assembly instructions carefully before beginning assembly.
4. The packaging and contents can be a choking hazard, therefore keep out of reach
of small children at all items.
5. Do not over tighten the bolts as this may damage the thread.
ALLOW 45 MINUTES 2 PEOPLE REQUIRED
ADDITIONAL TOOLS REQUIRED

3 / 8 67093
JCBC Bolt M6x15mm
Ax 8 pcs Allen Key - M6
PARTS LIST
NO. PART QTY. PICTURE PACKING CARTON
1 HEAD BOARD 1 PC 1/3
2FOOT BOARD 1 PC 2/3
3SIDE RAIL - L/R 2 PCS 3/3
4 CROSS BAR 2 PCS 3/3
5
CENTRE BAR 1 PC 3/3
6
SUPPORT LEG c/w JCBB Bolt M8x40mm 3 PCS 3/3
7WOOD SLAT (7pcs/set)
- 18mm x 59mm x 1523mm 2 SETS 3/3
JCBC Bolt M6x30mm JCBC Bolt M6x100mm
+ Barrel Nut
CSK Chipboard Screw
#4 x 30mm
Allen Key - M8
Bx 2 pcs Dx 4 pcs
Cx 8 pcs
Gx 1 pc Hx 1 pc
JCBB Bolt M8x40mm
+ Spring Washer
Ex 4 pcs Fx 8 pc
Wood Dowel M8x30mm

4 / 8 67093
1
3
3
5
6
6
6
4
4
2
7
7

5 / 8 67093
STEP 1 :
STEP 2 :
Wood Dowel M8x30mm
Fx 8 pcs
Attach side rail (3) to head frame (1) and foot frame (2) using hardware (D), (E) and (F).
Important Note : Do not tighten the bolts yet!
Attach cross bars (4) to side rails (3) at head end with bolts (A) as shown in diagram. Repeat at foot end.
Tighten all bolts with Allen key (G) by turning clockwise.
JCBC Bolt M6x15mm
Ax 8 pcs
D
16
F
E
Dx 4 pcs
JCBC Bolt M8x40mm
+ Spring Washer
Ex 4 pcs
JCBC Bolt M6x100mm
+ Barrel Nut
A
3
3
2
1
4
4

6 / 8 67093
Fix centre rail (5) to cross bars (4) with bolts (B) using Allen key (G) as shown
below.
STEP 3 :
Attach support legs (6) to centre rail with bolts using Allen key (H) as shown.
STEP 4 :
JCBC Bolt M6x30mm
Bx 2 pcs
5
B
6

7 / 8 67093
CSK Chipboard Screw
#4 x 30mm
Cx 8 pcs
Insert wooden slats (7) into the side rail support and fix with screws (C) at hole as shown below.
STEP 5 :
C
7
ASSEMBLY IS COMPLETE

8 / 8 67093
Product Care for Hi-Gloss Items
Hi-gloss lacquered furniture is more sensitive to marks and scratching then some other furniture
products. It is important to exercise caution and care to maximise the life and beauty of
this product.
Following the below simple guidelines when using your hi-gloss product will protect your
investment for years to come.
.Dust frequently with a clean damp lint-free cloth. This will help remove
abrasive build up which can damage a finish over time.
.Do not place hot objects on any furniture surface. Always use a hot plate or
placement. Laminate and lacquer finishes on table tops provide added scratch
and heat resistance to our furniture, but they can still be damaged without
proper care.
.Avoid exposing your furniture to strong sunlight, heat outlet, open windows or
dampness. Prolonged exposure to direct sunlight can fade the finish of your
furniture, while extreme temperature and humidity changes can cause
cracking or splitting.
.Do not expose your furniture to any liquids. Never allow water to sit on your
furniture. Alcohol, nail polish and perfume are also dangerous as they will
dissolve the lacquer finish on contact and may require professional repairs.
.Do not allow plastic to come in direct contact with your furniture. Chemicals in
the plastic of placements etc may soften and mark the finish if left in contact
with the furniture for a period of time.
.Avoid placing sharp or rough objects on the surface of your furniture. These
may scratch the surface of the product.
.When moving your furniture, do not drag it across the floor. This may damage
the product. Instead use two (2) people to lift carefully from either end.