Amart Furniture BAJA 73856 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
BAJA Gaming Chair
ITEM CODE 73856
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1 73856

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2 73856
X2
ADDITIONAL TOOLS REQUIRED

PARTS LIST
1
Headrest
2
Back
3
Backrest
4
Armrest
5
Regulator
6
Seat
7
Mechanism
8
Three cups
9
Gas lift
10
Base
11
Castor
3 73856
7
1
2
3
6
8
5
4
9
Gasket Screw cover
Cover 2 Screwdriver
Screw
A CB
D E
1pc 1pc F
Cover 1
1pc
16pcs
M8X20mm 4pcs
φ17Xφ8.5X1mm 6pcs
M5X8mm
10
11

STEP 1:
1. Insert castor 11 into base 10.
2. Insert gas lift 9 into base 10, then place three cups 8 on gas
lift 9.
STEP 2:
Connect mechanism 7 to seat 6, twist screw A and tighten with
screwdriver F.
4 73856
6
8
9
7
A
10
11

STEP 3:
Connect armrest 4 to seat 6. Twist in screw A and fasten with
screwdriver F.
STEP 4:
Connect regulator 5 to back 2. Twist in screw A and gasket B
and tighten with screwdriver F.
5 73856
4
6
A A
2
6
5
A ABB

6 73856
STEP 5:
Insert the cover D and E, twist the screw and cover C, tighten
with screwdriver F.
STEP 6:
Place mechanism 7 on gas lift 9.
C C
C C
9
7
D E

7 73856
STEP 7:
Installation method for the top pillows and lower pillows.
STEP 8:
ASSEMBLY IS COMPLETE
Top pillows installed Lower pillows installed
1.Pass both ends of the adjustment
strap through the seat back hole.
2.Fasten both ends of the adjustment strap.
Adjustment strap
2.Pull the adjustment strap and
fasten it.Repeat the above operation
for the second adjustment strap.
Figure 2
Figure 1
Figure 2
Figure 1
Adjustment strap
1.Move the adjustment strap
across the back of the chair where
it is attached to the seat.

GENERAL PRODUCT CARE
●DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER.
●USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME.
●DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
●AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
●IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
●FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
8 73856
CARE AND MAINTENANCE
OFFICE CHAIR
DO NOT REMOVE THIS LABEL